Blonder tongue HDE-8C DIN SERIES User manual

HDE-8C DIN SERIES
QUICK GUIDE
STEP 1 - Connect the Inputs
P/N:651245800A Stock #6371 QIP | #6371 Q v20180523
www.blondertongue.com
EAS
8xDIN (Component)
HD MPEG-2 Encoding
DOLBY®Digital Audio Encoding
(8 HD Programs Total)
4xQAM8xIP*
(8 HD Programs)
* Stk# 6371 QIP Only
HD Device
#2
HD Device
#1
HD Device
#8
INPUT #1 - INPUT #8
Possible
Sources
• Connect the unit as pictured here
• Power up the encoder.
Stk#
3701
PC with web browser IP=172.16.70.1
Connect 40dB
of aenuaon
See next page
for DIN cable
information

STEP 1 - Connect the Inputs
STEP 3 - Login
• Log in to the HDE-8C DIN Series encoder, using a standard web browser.
• This can be done through the Control 10/100 port, next to the Receiver Control port. Either go
directly from a computer or through an Ethernet switch
• Assign 172.16.70.2 as the static address for your computer
• Now open your browser and enter 172.16.70.1 to access the HDE-8C DIN Series encoder
• The Username is “Admin” and the password is “pass” (case-sensitive)
CONNECTOR COLOR TYPE
P2 GREEN Y
P3 RED Pr
P4 BLUE Pb
P5 ORANGE DIGITAL
AUDIO
P6 RED RIGHT
AUDIO
P7 WHITE LEFT
AUDIO
P8 YELLOW NTSC
P1 - 13-PIN DIN PLUG
Stock # 3701 - H258C DIN to RCA Cable:
The DIN to RCA pin connectors are
labeled here for your reference.

STEP 4 - TS Configuration
STEP 5 - Configure IP Output*
Go to the Main > Output > TS Cong Tab
Verify the Multiplexed MPTS Output default
settings are suitable for your application
- TS bitrate = QAM Modulator
- Modulation Mode = QAM 256
- Out of band = disabled
Verify the Output Mapping Section.
- Input for each TS must be different.
- Every PID and Program Number must be
different.
- Short Name should be a descriptive
name of the program, as it will be shown
on the television (max 7 alphanumeric
characters)
- Major and Minor Channel numbers are
what the TV will display as the channel.
Click “SAVE” at the bottom to apply changes.
1
2
3
Go to the Main > Output > IP Tab
Assign the Destination IP, Encapsulation protocol, Destination and Source Ports for each
transport stream.
Verify the Stufng is set to “Disabled” and the Output is “Enabled”
Click “SAVE” to apply the settings.
1
2
3
NOTE: The IP Output Tab is only available on the HDE-8C-QAM/IP DIN model.
3
1 2
1
2
3

Please visit our website at www.blondertongue.com to download the latest User Manual (PDF). Navigate
to the product page by entering the Full (or Partial) Model Name or Stock Number within the search eld.
Upon reaching the product page, the “User Manual” download link will be located beneath the product
image.
Firmware Updates are available under “Tech Support” in the “Resources” section of the website. General
instructions for the FTP site, as well as updating your rmware, are provided on this page.
CONTACT BT FOR MORE INFO | TECH SERVICES: 732-679-4000 x 4358
STEP 6 - Configure QAM Output
Setup the QAM output channels by going to the Main > Output > QAM tab
Select the channel for the 1st QAM. The next 3 will be automatically assigned.
Ensure all outputs are on and CW mode is not enabled.
Click “SAVE” to apply changes.
2
1
3
1
2
3