bluBathworks TSP211.01 User manual

2017-08
1 866 907 0122 blubathworks.com
In-wall Basin Mixer
Installation Guide
TSP211.01

2017-08
1 866 907 0122 blubathworks.com
1
Attention – Before Installation
1. Inspect this product to ensure you have all parts as shown that are required for proper installation.
2. The valve cartridge has been factory tested and adjusted – DO NOT TAKE THE CARTRIDGE APART. Taking the
cartridge apart will void the warranty.
3. Ensure that both hot and cold water feeds are properly connected to the marked lav connecting.
4. This product must be installed by a professional contractor.
5. Refer to the specication and assembly drawings attached for installation directions.
6. Flow Pressure –Min. 25 PSI, Max. 80 PSI. Recommended pressure – 50 to 60 PSI.
Installation Requirements
Please read the instructions carefully so as to avoid any damage to the xture.
1. To ensure this product is installed properly, you must read and follow these guidelines.
2. The owner/user of the faucet must keep this information for future reference.
3. Be sure your installation conforms to local codes.
4. Refer to the specication and assembly drawings attached. Faucet is sold partially assembled but shown fully
disassembled for illustrative and service purposes only.
5. Inspect this product to ensure you have all parts required for proper installation.
6. Use only a strap wrench or protected/smooth-jaw wrench on any nished surface.
7. If possible, install the faucet assembly on the sink or mounting surface before setting.
8. Do NOT use putty during this installation.
Cleaners For Fittings And Accessories
To avoid damaging the surface and working components of the ttings, certain precautions must be taken in terms of us-
age and subsequent cleaning as many cleaning agents contain acids for general cleaning and removing calcium depos-
its. When caring for your ttings and accessories, please note the following:
- Only apply cleaners which are expressly intended for the use
- Never use any cleaner containing hydrochloric acid, formic acid or acetic acid on or near the tting, as they can
cause considerable damage
- Do not use cleaners containing phosphoric acid
- Do not use cleaners containing chlorine bleach solutions
- Never mix or combine cleaning agents
- Abrasive cleaners and unsuitable scouring agents such as scouring pads
Technical Support Assistance
If further assistance is required, please contact:
Product Support at 1.866.907.0122 (09:00 – 17:00hrs PST) or email [email protected]
North America
Blu Bathworks Inc.
188 Smithe Street,Vancouver, BC, Canada, V6B 6A9
T +1.604.299.0122 F +1.604.299.0125
Please refer to blubathworks.com for warranty, terms & conditions under warranty & procedure for warranty service.

2017-08
1 866 907 0122 blubathworks.com
2
CARTRIDGE CHANGE
Through years of use impurities and limescale could damage the cartridge. To replace it, refer-
ence the following instruction.
• Shut o water supply to both inlets
• Remove the control lever (1), remove the screw (2), take o the control handle (3) and pull
out the cup (4).
• Pay attention not to lose the O-ring (5).
• Unscrew the ange (6) using 30mm/11/6” spanner. Remove the cartridge (7).
• Before re-assembling cartridge (7) clean its housing with wet cloth.
• Re-assembling the ange (6).
• Place the O-ring (5) and re-t the cap (4).
• Re-t the control knob (3) and x it with the grub screw (2).
• Re-t the lever (1).
IMPORTANT
In case of reduction of ow rate, dismantle the aerator and clean the lter inside or change it.

2017-08
1 866 907 0122 blubathworks.com
3
TSP211.01
BACK VIEW
TOP VIEW

2017-08
1 866 907 0122 blubathworks.com
4
TSP211.01
P1293G80103
P0000000287
P1293000034
P0000000501
P1293G80104
P0000000288
P0000000286
P0000000513