Blue Diamond 124010 User manual

Operation and Maintenance Manual
VIBRATORY ROLLER
Register your
WARRANTY
within 30 days
of purchase
888-376-7027 | BlueDiamondAttachments.com
124010 - 73” SMOOTH VIBRATORY ROLLER
124015 - 73” PAD FOOT VIBRATORY ROLLER
124030 - 84” SMOOTH VIBRATORY ROLLER
124035 - 84” PAD FOOT VIBRATORY ROLLER

TABLE OFCONTENTS
Safety Information . . . . . . . . . . . . . . . . . . . . . . 1
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . 3
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Before Starting & Operating . . . . . . . . . . . . . . . . . . . . 4
Connecting to Loader . . . . . . . . . . . . . . . . . . . . . . . . . 4
Operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Maintenance Schedule. . . . . . . . . . . . . . . . . . . . . . . . 5
Fluid Levels.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Changing Exciter Oil. . . . . . . . . . . . . . . . . . . . . . . . . . 5
Checking Exciter Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Torque Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Service Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Replacing Shockmounts. . . . . . . . . . . . . . . . . . . . . . . 7
Replacing Input Seal . . . . . . . . . . . . . . . . . . . . . . . . . 7
Removing Drive Coupler . . . . . . . . . . . . . . . . . . . . . . 7
Installing Drive Coupler . . . . . . . . . . . . . . . . . . . . . . . 8
Removing Exciter Bearings and Shaft.. . . . . . . . . . . . 8
Installing Exciter Bearings and Shaft.. . . . . . . . . . . . . 8
Parts Replacement Cycles and Tolerances. . . . . . . . 9
Replacement Parts. . . . . . . . . . . . . . . . . . . . .11
Drum Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Main Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Spider Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

This Page Intentionally Left Blank

- 1 -
SAFETY INFORMATION
Introduction
This Safety Alert Symbol is used to call attention
to items or operations which may be dangerous
to those operating or working with this
equipment. The symbol can be found
throughout this manual and on the unit. Please read these
warnings and cautions, along with all decals, carefully
before attempting to operate the unit. Make sure every
individual who operates or works with this equipment is
familiar with all safety precautions.
WARNING
GENERAL WARNING. Indicates information
important to the proper operation of the
equipment. Failure to observe may result in
damage to the equipment and/or severe bodily
injury or death.
CAUTION
GENERAL CAUTION. Indicates information
important to the proper operation of the
equipment. Failure to observe may result in
damage to the equipment.
Safety Precautions
LETHAL EXHAUST GAS: An internal
combustion engine discharges carbon
monoxide, a poisonous, odorless, invisible
gas. Death or serious illness may result if
inhaled. Operate only in an area with proper
ventilation. NEVER OPERATE IN A
CONFINED AREA!
DANGEROUS FUELS: Use extreme caution
when storing, handling and using fuels, as
they are highly volatile and explosive in vapor
state. Do not add fuel while engine is running.
Stop and cool the engine before adding fuel.
DO NOT SMOKE!
SAFETY GUARDS: It is the owner's
responsibility to ensure that all guards and
shields are in place and in working order.
IGNITION SYSTEMS: Breakerless, magneto,
and battery ignitionsystems can cause severe
electrical shocks. Avoid contacting these
units or their wiring.
SAFE DRESS: Do not wear loose clothing,
rings, wristwatches, etc. near machinery.
NOISE PROTECTION: Wear OSHA specified
hearing protection devices.
EYE PROTECTION: Wear OSHA specified
eye shields, safety glasses, and sweat bands.
FOOT PROTECTION: Wear OSHA specified
steel-tipped safety shoes.
HEAD PROTECTION: Wear OSHA specified
safety helmets.
DUST PROTECTION: Wear OSHA specified
dust mask or respirator.
OPERATOR: Keep children and bystanders
off and away from the equipment.
REFERENCES: For details on safety rules and regulations
in the United States, contact your local Occupational Safety
and Health Administration (OSHA) office. Equipment
operated in other countries must be operated and serviced
in accordance and compliance with any and all safety
requirements of that country. The publication of these
safety precautions is done for your information. Blue
Diamond does not by the publication of these precautions,
imply or in any way represent that these are the sum of all
dangers present near Blue Diamond equipment. If you are
operating Blue Diamond equipment, it is your responsibility
to insure that such operation is in full accordance with all
applicable safety requirements and codes. All requirements
of the United States Federal Occupational Safety and
Health Administration Act must be met when operated in
areas that are under the jurisdiction of that United States
Department.
Safety Decals
Carefully read and follow all safety decals. Keep them in
good condition. If decals become damaged, replace as
required. If repainting the unit, replace all decals. Decals
are available from authorized Blue Diamond distributors.
Order the decal set listed on the following page(s).

- 2 -
Hydraulic Requirements
Return
Pressure
PRESSURE: 1500-3000 psi
(103-207 bar)
FLOW: 10-50 gpm
(38-190 l/m)
14435




Safety Decals (Decal Set #14436)
18075-AT84
18074-AT74 (Not Shown)
14434
14435
11922
CAUTION
HEAVY
ATTACHMENT
14434
READ OPERATORS MANUAL
BEFORE USING ATTACHMENT
Overloading skid loader
could cause loader to pitch
or tip forward.
Check lifting capacity of skid
loader before hooking onto
attachment.
Do not lift attachment over
12 (30cm) above ground
level.
WARNING
Machine may fall and cause
serious damage or injury if
lifted improperly.
Lift only by holes in frame
above.
MACHINE WEIGHT
ATS84- 2260 lbs (1025 kg)
ATP84- 2410 lbs (1093 kg)
18075

- 3 -
SPECIFICATIONS
Specifications subject to change without notice
124010 124015 124030 124035
Centrifugal Force 8850 lbs (4014 kg) 9765 lbs (4429 kg)
Exciter Speed 3000 rpm 3000 rpm
Dynamic Linear Force 121 lb/in (21.7 kg/cm) 116 lb/in (20.8 kg/cm)
Amplitude --
Length 43.3 in (110 cm) 43.3 in (110 cm)
Height 29 in (74 cm) 30 in (76 cm) 29 in (74 cm) 30 in (76 cm)
Weight 2070 lbs (939kg) 2210 lbs (1002 kg) 2300 lbs (1043 kg) 2450 lbs (1111 kg)
Width, Working 73 in (185 cm) 84 in (213 cm)
Width, Overall 78 in (198 cm) 89 in (226 cm)
Sound Pressure Level 85 dBa 85 dBa
Pressure Requirement 1500 - 3000 psi (10.3 - 20.7 MPa) 1500 - 3000 psi (10.3 - 20.7 MPa)
Flow Rate Requirement 10 - 50 GPM (38 - 176 LPM) 10 - 50 GPM (38 - 176 LPM)
Connection 1/2” Flat-face Quick Coupling 1/2” Flat-face Quick Coupling

- 4 -
OPERATION
Introduction
Blue Diamond equipment is intended for use in very severe
applications.
This parts manual contains only standard parts. Variations
of these parts as well as other special parts are not included.
Contact your local Blue Diamond distributor for assistance
in identifying parts not included in this manual.
Before Starting & Operating
• REMEMBER! It is the owner’s responsibility to
communicate information on the safe use and proper
operation of this unit to the operators.
• Review ALL of the Safety Precautions listed on page 1 of
this manual.
• Familiarize yourself with the operation of the machine
and confirm that all controls function properly.
• Know how to STOP the machine in case of an
emergency.
• Make sure hands, feet, and clothing are at a safe
distance from any moving parts.
Connecting to Loader
1. Attach the roller to the skid steer loader with the
universal bracket. Be sure that the wedges and
levers are fully engaged and locked.
2. Connect the hydraulic hoses to the skid steer loader’s
auxiliary hydraulics supply using the quick couplers.
3. If skid loader is equipped with a high flow and low flow
ports, it is recommended to use the low flow side.
4. Lower the roller, and engage the loaders’ arms into
their float mode.
5. Engage the auxiliary hydraulics and allow the vibrator
to come up to speed.
Operating
• Check for loose hardware every 20 hours of operation.
• Do not run exciter when roller is not in contact with the
ground.
• Check that rated capacity of skid steer loader meets or
exceeds weight of roller attachment.
• The operating pressure supplied to the control valve
must fall in the range of 1500 to 3000 psi.
• Theminimum volume requirementsuppliedto the control
valve is 10 gpm, but do not exceed 50 gpm.
• Do not use excessive down pressure when compacting
soil.
WARNING
Always stop the engine before:
Adding fuel.
Leaving the equipment unattended for any
amount of time.
Before making any repairs or adjustments to the
machine.

- 5 -
MAINTENANCE
WARNING
Always exercise the stopping procedure before
servicing or lubricating the unit.
After servicing the unit, replace and fasten all
guards, shields, and covers to their original
positions before resuming operation.
CAUTION
Always verify fluid levels and check for leaks after
changing fluids.
Do not drain oil onto ground, into open streams,
or down sewage drains.
Maintenance Schedule
1. Check all hardware after the first 5 hours of use, then follow the maintenance schedule.
Fluid Levels.)
Changing Exciter Oil
1. Rotate drum until the fill/drain plug is at bottom of
drum. The fill/drain plug is the larger, square head
plug on the vent side of the roller.
2. Place drain pan under plug and remove both plugs.
3. Raise driven side of drum several inches soall oil can
drain out.
4. After all oil has drained, return drum to a level
surface.
5. Rotate drum until fill/drain plug is at the top of the
drum.
6. Remove oil check plug from bottom of cover. The oil
check valve is smaller than the fill plug, and it has an
allen head drive as opposed to the square head
found on the fill/drain plug.
7. Fill exciter with Oil until oil starts to drain from oil
check plug. See chart for proper amounts.
8. Replace both plugs.
SYSTEM MAINTENANCE EACH USE EVERY 50
HOURS EVERY 250 HOURS YEARLY
Exciter Check oil level X
Check for oil leaks X
Change oil XX
Tighten Bolts1XX
Hardware Check and tighten as needed1XX
Shock mounts Check for cracks or tears XX
SYSTEM FLUID VOLUME RECOMMENDED OIL
73” Exciter 80 oz. CALL
84” Exciter 128 oz. CALL
2LO)LOO'UDLQ
$FFHVV3OXJ
'21275(029(
2LOFKHFNSOXJ
224515 32 Oz. Bottle Exciter Oil
224515 32 oz. Bottle Exciter Oil

- 6 -
Checking Exciter Oil
1. Place drum on a level surface
2. Remove oil check plug. The plug is the smaller of the
two on the vent side which also has an allen head
drive.
3. Rotate drum until check plug is at 6 o’clock position.
4. If oil level is adequate, it should dribble out of hole.
5. If necasary, remove fill/drain plug, and add Blue
Diamond approved Oil.

- 7 -
SERVICE
Assembly and disassembly should be performed by a
service technician who has been factory trained on Blue
Diamond equipment. The unit should be clean and free of
debris. Pressure washing before disassembly is
recommended.
• Prior to assembly, wash all parts in a suitable cleaner or
solvent.
• Check moving parts for wear and failure. Refer to the
Replacement section in this manual for tolerance and
replacement cycles.
• All shafts and housings should be oiled prior to pressing
bearings. Also, ensure that the bearings are pressed
square and are seated properly.
• All bearings should be replaced when rebuilding any
exciter or gearbox.
• All gaskets and seals should be replaced after any
disassembly.
Torque Chart
Service Tools
Replacing Shockmounts
1. Support roller to prevent it from rolling, and remove
hydraulic hoses from motor.
2. Remove the two bolts securing the hydraulic motor
and remove the motor.
3. Remove all external shockmount hardware while
supporting frame. Lift frame assembly off of drum
assembly.
4. Pull spider off of drum.
5. Replace shockmounts as needed.
6. While spider is removed, inspect coupling and seal
for excessive wear. Replace if needed.
7. Reinstall spider onto drum and then into the frame
8. Install motor, align with coupler and secure with
mounting screw and lock washer. Use a medium
strength thread locker. Make sure motor mount
surface bottoms out in frame.
9. Connect hoses.
Replacing Input Seal
Refer to Main Assembly, page 14.
1. Remove drum assembly from frame and spider from
drum (See “replacing shockmounts” steps 1-4)
2. Using a seal puller, remove seal. Note it is not
necessary to remove gear coupler (#15)
3. Inspect the sealing surface on the shaft for wear or
damage.
4. If the shaft has any sign of wear or damage, remove
the gear coupler (#15) and use the sleeve included
with seal. (Follow instructions included with seal kit).
If the shaft is in good condition install only the seal.
Use a seal protector when installing the seal.
Removing Drive Coupler
Refer to Main Assembly, page 14.
1. Remove hydraulic lines from motor.
2. Remove hydraulic motor (# 6).
3. Remove drive coupler (# 13) gear from motor by
loosening clamping screw.
SIZE GRADE 2 GRADE 5 GRADE 8
1/4-20 49 in•lbs 76 in•lbs 9 ft•lbs
1/4-28 56 in•lbs 87 in•lbs 10 ft•lbs
5/16-18 8 ft•lbs 13 ft•lbs 18 ft•lbs
5/16-24 9 ft•lbs 14 ft•lbs 20 ft•lbs
3/8-16 15 ft•lbs 23 ft•lbs 33 ft•lbs
3/8-24 17 ft•lbs 26 ft•lbs 37 ft•lbs
7/16-14 24 ft•lbs 37 ft•lbs 52 ft•lbs
7/16-20 27 ft•lbs 41 ft•lbs 58 ft•lbs
1/2-13 37 ft•lbs 57 ft•lbs 80 ft•lbs
1/2-20 41 ft•lbs 64 ft•lbs 90 ft•lbs
9/16-12 53 ft•lbs 82 ft•lbs 115 ft•lbs
5/8-11 73 ft•lbs 112 ft•lbs 159 ft•lbs
5/8-18 83 ft•lbs 112 ft•lbs 180 ft•lbs
3/4-16 144 ft•lbs 200 ft•lbs 315 ft•lbs
1-8 188 ft•lbs 483 ft•lbs 682 ft•lbs
1-14 210 ft•lbs 541 ft•lbs 764 ft•lbs
1-1/2-6 652 ft•lbs 1462 ft•lbs 2371 ft•lbs
M 6 3 ft•lbs 4 ft•lbs 7 ft•lbs
M 8 6 ft•lbs 10 ft•lbs 18 ft•lbs
M 10 10 ft•lbs 20 ft•lbs 30 ft•lbs
CONVERSIONS
in•lbs x 0.083 = ft•lbs
ft•lbs x 12 = in•lbs
ft•lbs x 0.1383 = kg•m
ft•lbs x 1.3558 = N•m
Part # Description
07353 CLUTCH REMOVAL TOOL

- 8 -
4. To remove coupler gear (# 15) from exciter shaft will
require 07353 clutch removal tool. Turn coupler gear
clockwise (left hand threads) to remove.
Installing Drive Coupler
Refer to Main Assembly, page 14.
1. Install new coupler gear (# 15) into shaft. Make sure
coupler bottoms out. Use high strength threadlocker.
2. Slide new coupler gear on to motor splines and
tighten clamping screw. Use a medium strength
thread locker on the screw.
3. Install motor (# 6), align with coupler and secure with
mounting screw (# 23) and lock washer (# 24). Use
a medium strength thread locker. Make sure motor
mount surface bottoms out in frame.
4. Connect hoses.
Removing Exciter Bearings and Shaft.
Whenever a complete disassembly is done all bearings,
gaskets, O-rings and seals should be replaced.
Refer to Drum Assembly, page 12.
1. Drain exciter oil (Refer to Changing Exciter Oil, page
5.)
2. Remove drum assembly from frame and spider from
drum (Refer to Replacing Shockmounts, page 7.
Steps 1-4).
3. Remove input seal (# 10) from housing (# 14) using a
seal puller.
4. Remove snap ring (# 9) from exciter shaft through
seal bore.
5. Remove six bolts (# 19), securing housing (#14), to
the drum.
6. Remove two push off bolts (# 19)
7. Thread two 3/8-16x1 ½ bolts into these push off holes
evenly and push cover (# 14) off of drum. (If boltsare
not threaded in evenly the cover will bind) Remove
cover.
8. Slide exciter shaft (#13) out of drum.
9. Repeat steps 5-7 to remove cover (# 5) from the other
side.
10. Remove breather cover (# 11) by removing four
screws (# 17).
11. Remove bearings (# 8) from covers (# 5 & 14).
(Bearings must be replaced if removed from covers)
Installing Exciter Bearings and Shaft.
Refer to Drum Assembly, page 12.
1. Install new bearings (# 8) into housings (# 5 & 14).
Use oil on the OD of the bearing and press on the
outer race of the bearing. Failure to do so will result
in damage to the bearings.
2. Install new O-rings (# 7) onto housing (# 5 & 14),
lightly grease O-ring and housing surface which
slides into the drum.
3. Install exciter shaft (# 13) into drum. Leave seal side
of exciter assembly stick out of the drum about 12".
4. Take the seal side housing assembly (# 14), lightly oil
the exciter shaft bearing journal and apply Loctite 515
gasket eliminator, or equilivant, to mating flange.
Slide housing assembly onto shaft and install snap
ring (# 9) through seal bore onto shaft. Do not install
seal at this time.
5. Slide exciter shaft and housing assembly into drum.
Use care to press housing in evenly. Secure with six
bolts (# 19). Use medium strength thread locker.
Install two bolts (# 18) in the push out holes to protect
the threads.
6. To aid in assembly, insert a piece of ¾" round stock in
the vent end of the exciter shaft. Take vent side
housing assembly (# 5), apply a light coat of oil to the
exciter shaft bearing journal, and Loctite 515 gasket
eliminator, or equilivant, to the mating flange. Slide
housing assembly over the ¾" round stock, exciter
shaft, and onto drum assembly. Have someone lift up
the exciter shaft while aligning the housing assembly
with mounting holes in the drum and slide the
assembly on evenly.
7. Install the six bolts (# 19) use medium strength thread
locker. Install two bolts (# 18) in the push out holes to
protect threads. Make sure exciter assembly rotates
freely.
8. Remove ¾" round stock and install vent cover (# 11).
Make sure felt filter (# 1), retainer (# 2) and spiral pin
(# 15) are in place.
9. Press seal into housing (# 14) using care to keep seal
square with bore.
10. Fill exciter housing with exciter oil. Refer to Changing
Exciter Oil, page 5. or proper procedure and amount.
11. Install drive gear coupler (# 16, page 14) if removed.
12. Install spiders and frame.

- 9 -
Parts Replacement Cycles and Tolerances
Bearings Replace anytime a bearing is rough, binding, discolored or removed from housing or
shaft.
Hardware Replace any worn or damaged hardware as needed. Replacement hardware should
be grade 5 and zinc plated unless otherwise specified.
Safety Decals Replace if they become damaged or illegible.
Seals & Gaskets Replace if a leak is detected and at every overhaul or tear down.

- 10 -
This page intentionally left blank.

- 11 -
REPLACEMENT PARTS
The warranty is stated in this book on page 14. Failure to
return the Warranty Registration Card renders the warranty
null and void.
Blue Diamond has established a network of reputable
distributors/dealers with trained mechanics and full facilities
for maintenance and rebuilding, and to carry an adequate
parts stock in all areasof the country. Their sales engineers
are available for professional consultation. If you cannot
locate an Blue Diamond distributor in your area, contact
Blue Diamond or one of our Sales Branches listed below.
When ordering replacement parts, be sure to have the
following information available:
• Model and Serial Number of machine when ordering
Blue Diamond parts
• Model and Serial Number of engine when ordering
engine parts
• Part Number, Description, and Quantity
• Company Name, Address, Zip Code, and Purchase
Order Number
• Preferred method of shipping
REMEMBER - You own the best! If repairs are needed,
use only Blue Diamond parts purchased from
authorized Blue Diamond distributors. The unit’s serial number can be found in the following locations:
• The model and serial number are on the top front of the
roller frame
• The serial number is also stamped on the frame side
Write Model Number here
Write Serial Number here
DECAL
STAMP

- 12 -

























Drum Assembly

- 13 -
ITEM PART NO. DESCRIPTION
ATP73 ATS73 ATP84 ATS84
1. 01072 FILTER,FELT 1111
2. 01191 RETAININGRING,INTERNAL,STAR 1111
3. 07011 RETAININGRING,INTERNAL 2222
4. 08188 DECAL,EXCITEROIL 2222
5. 17807 COVER,EXCITER,BREATHERSIDE 1111
6. 17911 DRUM,ATP73(PADDED) 1000
17811 DRUM,ATS73(SMOOTH) 0100
17913 DRUM,ATP84(PADDED) 0010
17813 DRUM,ATS84(SMOOTH) 0001
7. 17844 O-RING,7.234IDX0.139DIA 2222
8. 17845 BEARING,SPHERICALROLLER 2222
9. 17846 RETAININGRING,EXTERNAL 1111
10. 18111 KIT, SEAL, AT73-84 1111
11. 17853 COVER,BREATHER 1111
12. 17854 GASKET, COVER 1111
13. 17858 SHAFT,AT73 1100
17859 SHAFT,AT84 0011
14. 17938 COVER, EXCITER, SEAL SIDE 1111
15. F0205SP PIN,SPIROL1/8”X5/8” 1111
16. F0418SPPSOCKETPIPEPLUG,1/4”-18 2222
17. F042005FSSFLATHEADSOCKETSCREW,1/4”-20X5/8” 4444
18. F061604HCSHEXHEADCAPSCREW,3/8”-16X1/2” 4444
19. F061610FWS FLANGE HEAD CAP SCREW, 3/8”-16 X 1-1/4” 12 12 12 12
20. F0618SHPPSQUAREHEADPIPEPLUG,3/8”-18 1111

- 14 -
11
26
27
28
30
29
19
9
20
22
14
24
25
5
2
1
12
13
15
3
1
6
16
17
8
7
10
23
21
4
18
23
Main Assembly

- 15 -
ITEM PART NO. DESCRIPTION
ATP73 ATS73 ATP84 ATS84
1. 08213 FITTING,STRAIGHT 3333
2. 08730 FITTING, ELBOW 1 1 1 1
3. 13166 HOSE,HYDRAULIC1/2”X47.00” 1100
17980 HOSE,HYDRAULIC1/2”X55.00” 0011
4. 13984 SHEET,SAFETYWALK24” 2222
5. 14267 MOTOR,HYDRAULIC 1111
6. 14747 FITTING,STRAIGHT 2222
7. 17842 FLATFACECOUPLING,MALE1/2” 1111
8. 17843 FLATFACECOUPLING,FEMALE1/2” 1111
9. 21004 FRAME,AT73 1100
21005 FRAME,AT84 0011
10. 17856 GAURD,HOSE 1111
11. 17924 SCRAPER BAR ATP73 (PADDED) 1000
17894 SCRAPER BAR ATS73 (SMOOTH) 0100
17925 SCRAPER BAR ATP84 (PADDED) 0010
17895 SCRAPER BAR ATS84 (SMOOTH) 0001
12. 17975 COUPLER,GEAR,9TSPLINE 1111
13. 17976 SLEEVE, COUPLER, GEAR 1111
14. 17977 COUPLER,GEAR,1”-12THREAD 1111
15. 17981 HOSE,HYDRAULIC1/2”X53.5” 1100
17979 HOSE,HYDRAULIC1/2”X59.00” 0011
16. 18107 VALVECOMBINATION(.203ORIFICE) 1111
17. 18127 HOSE,HYDRAULIC3/4”X64.00” 2222
18. 18656 BRACKET,LEFT 1111
19. 18657 BRACKET,RIGHT 1111
20. F051836HCSHEXHEADCAPSCREW,5/16”-18X4-1/2” 2222
21. F0518FN NUT,FLANGE5/16”-18 2222
22. F05SW WASHER,5/16”X3/4”X15GA 2222
23. F061607FWS FLANGE HEAD CAP SCREW, 3/8”-16 X 7/8” 11 11 11 11
24. F061610SCSSOCKETHEADCAPSCREW,3/8”-16X1-1/4” 2222
25. F06LW LOCKWASHER,3/8” 2222
26. F081312HCS HEX HEAD CAP SCREW, 1/2”-13 X 1-1/2” 24 24 24 24
27. F08LW LOCKWASHER, 1/2” 24 24 24 24
28. F101112HCSHEXHEADCAPSCREW,5/8”-11X1-1/2” 8888
29. F1011HN NUT,HEX5/8”-11 8888
30. F10LW LOCKWASHER,5/8” 8888
NOT SHOWN
17994 SEALKITFOR14267HYDRAULICMOTOR 1111

- 16 -





Spider Assembly

- 17 -
ITEM PART NO. DESCRIPTION QTY PER
SIDE
1. 12475 MOUNT, TORSION 1/2”-13 PRESSNUT 6
2. 17847 RETAINING RING, EXT 1
3. 17849 BEARING, BALL 1
4. 18106 SPIDER, DRUM 1
5. F071412HCS HEX HEAD CAP SCREW, 7/16”-14 X 1-1/2” 12
6. F0714ELN LOCKNUT, 7/16”-14 NYLOC 12