Blue Sea Systems 8058 User manual

Marine Electrical Prod ucts
PN 8058/ PN 3058/ PN 8059/ PN 3059/ PN 8265/ PN 3265
PN 8460/ PN 3460/ PN 8461/ PN 3461/ PN 8480/ PN 3480
Panel Specifications
Material: 0.125” 5052-H32 Aluminum Alloy
Primary Finish: Chemical Treatment per Mil Spec C-5541C
Final Panel Finish: Graphite color 2 part textured Polyurethane
Circuit Breakers: 15 amp Single Pole AC/DC Magnetic Breakers
65VDC/277VAC maximum
Amperage Rating: Panel Main Bus is rated for 50 amps maximum
Voltage Rating: Panels are rated for 120 volts AC and are so
marked in order to comply with ABYC standards
PN Inches Millimeters
Overall Dimensions: 8058/3058 5-1/4 x 3-3/4 133.4 x 95.3
8059/3059 5-1/4 x 7-1/2 133.4 x 190.5
8265/3265 14-3/4 x 7-1/2 374.7 x 190.5
8460/3460 14-3/4 x 4-1/2 374.7 x 114.3
8461/3461 10-1/2 x 7-1/2 266.8 x 190.5
8480/3480 5-1/4 x 11-1/4 133.4 x 285.8
Mounting Centers: 8058/3058 4-7/16 x 2-15/16 112.7 x 74.6
8059/3059 4-7/16 x 6-11/16 112.7 x 169.9
8265/3265 13-29/32 x 6-11/16 353.6 x 169.9
8460/3460 13-29/32 x 3-11/16 354.0 x 93.7
8461/3461 9-11/16 x 6-11/16 246.1 x 169.9
8480/3480 4-7/16 x 10-7/16 112.7 x 265.1
Standards: This panel, when properly installed, complies with
all applicable Standards and Recommended
Practices of the American Boat and Yacht Council
as well as United States Coast Guard 33 CFR Sub
Part 1. Blue Sea Systems Inc. Phone [phone]
425 Sequoia Drive Fax [phone]
Bellingham, WA 98226 USA E-mail [email protected]
www.bluesea.com
Document 9582 Rev.I
WARNING
@It is not possible within the scope of these instructions to fully acquaint
the installer with all the knowledge of electrical systems that may be
necessary to correctly install this product. If the installer is not
knowledgeable in electrical systems we strongly recommend that an
electrical professional be retained to make the installation.
@If either the panel front or back is to be exposed to water it must be
protected with a waterproof shield.
@The panels must not be installed in explosive environments such as
gasoline engine rooms or battery compartments as the circuit breakers
are not ignition proof.
@The vessel’s shore power cord must be disconnected form shoreside
power before installing this electrical panel.
@If an inverter is installed on the vessel its power leads must be
disconnected at the battery before the panel installation. Be aware that
many inverters have a “sleep mode” in which their voltage potential
may not be detectable with measuring equipment.
@If an AC Generator is installed aboard it must be stopped and rendered
inoperable before the panel is installed.
@Verify that no other AC source is connected to the vessels’ wiring
before the panel is installed.
Guarantee
Any Blue Sea Systems product with which a customer is not satisfied
may be returned for a refund or replacement at any time.
Installation
1. Disconnect all AC and DC power
Disconnect all AC power originating on or off the vessel. This includes
inverters, generators, shore power attachments and any other device
capable of supplying AC power to the ship’s circuits.
Disconnect the main positive DC cable from all batteries to eliminate
the possibility of a short circuit and to disable the inverter while
installing the distribution panel.
2. Select mounting location and cut opening
This panel is not intended to serve as the main AC circuit breaker
panel. A double pole circuit breaker that breaks both the AC hot and
neutral legs (such as Blue Sea Systems’ PN 8029) must be installed in
a location which is not more than 10 feet from the shore power inlet or
the electrical attachment point of a permanently installed shore power
cord as measured along the conductors of the feed wires.
Select a mounting location which is protected from water on the panel
front and back and is not in an area where flammable vapors from
propane, gasoline or lead acid batteries accumulate. The circuit
breakers used in marine electrical panels are not ignition protected and
may ignite such vapors.
Using the panel template provided, make a cut out in the mounting
surface where the distribution panel is to be mounted. Do not yet
fasten the panel to the mounting surface.
3. Install branch circuit wires
Determine the proper wire size for each branch circuit using the chart
below. Verify that the standard 15 amp circuit breakers installed in the
panel are correct for each branch circuit. Remove and replace any that
are incorrectly sized. The circuit breaker must have a rating less than
the allowable amperage of the wire, yet greater than the circuit’s
continuous current.
AC Power Distribution Panels
Connect each branch circuit hot (black) to the appropriate load
terminal. Connect each branch circuit neutral (white) to one of the
screws on the neutral bus. Connect each branch safety ground wire
(green) to one of the screws of the safety ground bus.
Do not confuse the neutral current carrying wires (sometimes called
ground) with the green normally non-current carrying wires (sometimes
called grounding). These two wires must be connected only at the
source of power, nowhere else.
Wire sizing chart
Use the wire sizing chart below to determine the proper branch and
feed circuit wire sizes.

Installation (continued)
4. Install feed circuit wires
Install the feed wires from the AC main circuit breaker panel or other
AC source, referring to the wire sizing chart to select the correct wire
size. Connect the black AC hot, white AC neutral and green AC safety
ground to their corresponding buses. In the case of the 24 position
panel, the black AC hot, white AC neutral and green AC safety ground
should be connected to the middle bus structure.
5. Installation of Backlight System
The backlight board is a DC device. When installing it in an AC panel
both wire leads must be connected to an appropriate DC source and
ground.
Connect the yellow negative wire to a DC ground. Connect the red
postive wire to any DC positive supply, ussually a switch that controls
the vessel’s other nighttime illumination.
6. Apply branch circuit labels and mount panel
Apply a label for each of the branch circuits from the 30 basic labels
provided. If the appropriate label is not included, the Extended Label
Set of 120 labels may be ordered from your marine supplier (PN 8067).
Individual labels are also available from Blue Sea Systems for specific
applications. Refer to the label order form for a complete listing of
individual labels.
Fasten the panel to the mounting surface using the panel mounting
screws supplied with the panel.
7. Testing
@Using a multimeter where the power source is connected to the
panel verify:
a. 120 volts between hot and neutral
(nominal, this may vary depending on source voltage)
b. 120 volts between hot and ground.
c. 0 volts between neutral and ground.
@Turn on each branch circuit to verify power to each circuit.
Optional Branch LED’s
This Panel is supplied with LED’s pre-installed in all optional branch
positions. For future expansion of the panel remove the hot leg of the
LED from the AC neutral bus and connect it to the Load side of the
appropriate branch cicuit breaker.
Note
This Blue Sea Systems electrical distribution panel is furnished with
15 amp AC/DC circuit breakers for all branch circuits. This rating was
selected to minimize the need for removing the panel’s circuit breakers
and reinstalling different size circuit breakers. It is rare to have more
than 15 amps of current flowing in any one circuit. Therefore, 15 amp
circuit breakers will satisfy the vast majority of marine circuit protection
situations.
Related Products from Blue Sea Systems
• PanelBack Insulating Covers
• High Amperage Fuses and Circuit Breakers for positive feed wires
• High Amperage Battery Switches
• Terminal Blocks and Common Bus Connectors
• AC Distribution Panels
• DC Distribution Panels
• AC and DC Digital and Analog Voltmeters and Ammeters
The Purpose of a Panel
There are five purposes of a marine electrical panel:
• Power distribution
• Circuit (wire) protection
• Circuit ON/OFF switching
• Metering of voltage and amperage (In panels with meters)
• Condition Indication (circuit energized)
Useful Reference Books
Calder, Nigel, 1996: Boatowner’s Mechanical and Electrical Manual,
2nd edition, Blue Ridge Summit, PA: TAB Books, Inc.
Wing, Charlie, 1993: Boatowner’s Illustrated Handbook of Wiring,
Blue Ridge Summit, PA: TAB Books, Inc.
Wiring Diagram
AC Distribution Panel
PN 8058 / PN 3058
Wiring Diagram
AC Distribution Panel
PN 8059 / PN 3059
TO DC
NEGATIVE
FROM DC
POSITIVE
FUSE
1.0 TO 2.0A
DC BACKLIGHT
BOARD
TO DC
NEGATIVE
FROM DC
POSITIVE
FUSE
1.0 TO 2.0A
DC BACKLIGHT
BOARD