elsner elektronik KNX WS1000 Color Reference guide

Brief Instruction Mounting KNX WS1000 Color
Elsner Elektronik GmbH • Sohlengrund 16 • D-75395 Ostelsheim • Germany
Status: 16.08.2012 • Errors excepted. Subject to technical changes.
Warning, mains voltage! National legal regulations are to be
observed. Installation, inspection, commissioning and
troubleshooting of the device must only be carried out by a
competent electrician.
Preparing the installation location
The device must only be installed and used in dry, interior
spaces. Avoid condensation.
Cut-out dimensions for concealed box (approx.): W=229 mm | H=163 mm | D=62 mm:
An external antenna can be connected in order to improve wireless communications.
During installation, a conduit 50 cm in length should be placed beneath the reces-
sed housing, in which the external antenna can be mounted (antenna dimensions
approx. 565 x 8 x 5, L × W × H in mm):

Brief Instruction Mounting KNX WS1000 Color
Elsner Elektronik GmbH • Sohlengrund 16 • D-75395 Ostelsheim • Germany
Status: 16.08.2012 • Errors excepted. Subject to technical changes.
Preparing for installation
The lid cover is only attached by a hinge. Take care not to lose it.
Conduit angled diagonally downwards
(for cable access from above or below)
Conduit angled vertically downwards
(only for cable access from above!)
concealed concealed
45°
cable
cable
box box
M16 conduit, 50 cm in length M16 conduit,
50 cm in length
To take off the front plate, remove the
screws beneath the lid.
Push the upper section of the housing
(frame with display) up a little and lift
it off.
Caution: The display is connected
with a flat-ribbon cable to the cir-
cuit board in the concealed box.
Loosen the plug so that the upper
section can be removed.

Brief Instruction Mounting KNX WS1000 Color
Elsner Elektronik GmbH • Sohlengrund 16 • D-75395 Ostelsheim • Germany
Status: 16.08.2012 • Errors excepted. Subject to technical changes.
Wall-fitting
Cavity wall fitting
The lower section of the housing to-
gether with the wall-mounting plate is
attached to the concealed box with 3
screws: Loosen the screws and take
off the lower part.
Remove the circuit board from the
concealed box to be installed a keep it
in a place where it is protected from
dirt. It may never be exposed to
dust or moisture!
For fitting, screw the cover (board) on
to the concealed box with the enclo-
sed screws.
Clamp the concealed box to the wall
with the four enclosed screws.
Upon delivery, the pouch containing
the assembly screws can be found in
the control unit’s flush-mounted ca-
sing.
or

Brief Instruction Mounting KNX WS1000 Color
Elsner Elektronik GmbH • Sohlengrund 16 • D-75395 Ostelsheim • Germany
Status: 16.08.2012 • Errors excepted. Subject to technical changes.
Assembling the control unit with concealed box
During electrical installation, please introduce all connection cables into the concealed
box through the lower or upper side wall. In the process, keep the individual connecti-
on wires short to prevent long reserve loops.
After connecting the cables screw the lower section of the housing (with the mounting
plate) onto the concealed box. Connect the flat ribbon cable to the display.
Put the lid cover on the upper section of the housing (frame with display). Put the upper
section of the housing onto the lower section of the housing from above and move it
downwards until the bottom edges are aligned. Screw on the upper section.
Structure of the connector board
1 Connector for flat-ribbon cable to
front board
2 Weather station:
terminal 1 (GND) and 2 (+).
Supply voltage (e. g. indoor sensor
or camera):
terminal 3 (12 V) and 4 (0 V) or
5 (12 V) and 6 (0 V),
max. 400 mA altogether
3 Programming button KNX
4 KNX bus plug +/-
5 Microfuse T630 mA
6 Mains connection L/N/PE 230 V/
50 Hz
1
2
3
4
5
6
123456