bluemyst BA1180WK User manual
Air Purier
Puricateur d’airs
Puricador de aire
Model / Modèle / Modelo: BA1180WK
Customer Support /
Assistance Au Client /
Servicio de atencion a clientes:
USA/ EE.UU: 1-800-790-7115
CANADA/ CANADÁ#: 1-888-209-0999
www.bluemyst.com
Email: [email protected]
#Canada Customer Support service available for models sold in Canada only.
EN
EN
Quick Start Guide ....................................................................................4
Safety Precautions ..................................................................................5
Product Description .................................................................................6
Control Panel Operation and Function ....................................................7
Remote Control Operation and Function ................................................8
Operation and Maintenance Guidelines ..................................................8
Operation and Maintenance Guidelines ................................................10
Air Filter Replacement ...........................................................................11
Troubleshooting .....................................................................................12
Warnings ...............................................................................................13
Contents Page
EN
4
Quick Start Guide
Fan speed
Sleep mode
O Timer
Turn on the device and press the fan speed button to adjust the fan speed.
Press the timer button to set the air purier to shut down after 1, 2, 4, or 8 hours.
Press the fan speed button to toggle the device to sleep mode. This will also mute the device
and turn o all other lights except for sleep mode. After 10 seconds, the sleep mode light will
also go out. Press any button to exit sleep mode.
fan speed
fan speed sleep mode
EN
5
Safety Precautions
Thank you for using a Bluemyst product. To assist you with reading the manual and using
the device safely, please be sure to carefully read and observe the contents of the following
symbols.
Do not spray any paint, pesticides, alcohol, or chemicals on the device surface otherwise, it may cause
surface cracks, electric shock, and/or re.
If there is an accumulation of cleaning or sanitation liquids inside the air purier, the substances will
be released from the vent, which may cause irritation. After using insecticide or any other aerosol
substance, please fully ventilate the room.
Air puriers should not be used in explosive or corrosive atmospheres.
When the device runs, the air inlet and outlet cannot be touched. To avoid injury to the user or damage
to the device, do not insert hands or any object into the inlet and outlet.
Do not sit on or place objects on the device, as this could cause injury, damage to the device or loss
of device parts.
Do not use in the bathroom or other places with water as it may cause re, electric shock or product
failure etc.
Do not alter, decompose, or repair the device without authorization as it may cause re, electric shock
or malfunction etc.
If the power cord or plug is damaged, stop using it immediately as it may cause electric shock or re.
Do not touch the power line with a wet hand.
When the device is undergoing maintenance, turn it o and disconnect it from the power source.
If the air purier is not being used for an extended period of time, disconnect it from the power supply.
When the device emits an unusual smell, turn it o and disconnect it from the power source. Check
with the Bluemyst customer service team for troubleshooting and measures that need to be taken to
avoid re, electric shock, or malfunction.
The air outlet can easily be contaminated with impurities. Be sure to prevent children from putting litter
into it and check before using it to ensure it is clear.
The air purier should be placed at least 50 cm from the wall and other objects.
If the power cord is damaged, it must be replaced immediately. Contact the Bluemyst customer service
team to arrange a replacement.
Any content with this sign must
be strictly prohibited, otherwise it
may cause damage to the device
or endanger the user’s personal
safety.
Any instruction with the above warning
sign should be observed closely to ensure
the personal safety of users. Please use
the device in strict accordance with the
contents of the warning.
EN
6
Product Description
Air outlet
Control panel
Handle
Front panel
Back cover
Composite Filter B:
Pre-lter, HEPA lter,
antibacterial lter
Timer ON/OFF Reset Speed
Composite Filter A:
cold catalyst lter,
activated carbon lter
EN
7
Control Panel Operation and Function
Power button
Press to start the device. Press again to stop the device and enter standby
mode.
Timer button
Press to set a time duration for the air purier to turn o. By pressing
repeatedly, you can set an automatic turn-o at a 1, 2, 4 or 8 hour duration.
The corresponding indicator light will turn on.
Filter reset button
When the device has been used for a total of 3,000 hours, the indicator will
light up. This indicates that the lter needs to be replaced. After replacement,
press the lter reset button for 3 seconds to turn o the indicator light and
restore the lter function.
Fan speed button
Press to choose the fan speed. By pressing repeatedly, you can cycle between
low, medium, high speed and sleep mode. The corresponding indicator light
will turn on.
fan speed
Power Filter Reset Fan SpeedTimer
EN
8
遥控器使用说明书
电源按键
风速按键 定时按键
滤网复位按键
风速按键
定时按键 滤网复位按键
Remote Control Operation and Function
Power button
Press to start the device. Press again to stop the device and enter standby mode.
Filter reset button
When the device has been used for a total of 3,000 hours, the indicator will light up.
This indicates that the lter needs to be replaced. After replacement, press the lter
reset button for 3 seconds to turn o the indicator light and restore the lter function.
Fan speed button
Press to choose the fan speed. By pressing repeatedly, you can cycle between low,
medium, high speed and sleep mode. The corresponding indicator light will turn on.
Timer button
Press to set a time duration for the air purier to turn o. By pressing repeatedly,
you can set an automatic turn-o at a 1, 2, 4 or 8 hour duration. The corresponding
indicator light will turn on.
Remote Control Battery Replacement
To change the battery, squeeze on the Lock and slide out the Battery Cover.
Remove the expired battery and replace with a new CR 2035 3v battery.
Lock
Battery Cover
遥控器使用说明书
电源按键
风速按键 定时按键
滤网复位按键
风速按键
定时按键 滤网复位按键
遥控器使用说明书
电源按键
风速按键 定时按键
滤网复位按键
风速按键
定时按键 滤网复位按键
EN
9
Setup Instructions
Open the back cover of the purier and take out the two packaged lters.
Remove the lters from their plastic packaging.
Insert the thinner Composite Filter A into purier. The black, circle-textured
active carbon lter should face toward you, with the pull tab pointing outwards.
Insert the wider Composite Filter B into the purier. The white meshed
antibacterial lter should face toward you, with the pull tab pointing outwards.
Replace the back cover. The air purier is ready for operation.
The air purifer ships with the two composite lters still in their packaging.
CAUTION: Air lters MUST be removed from their packaging before operating
the air purier.
Back Cover
Device Composite
Filter A
Composite
Filter B
EN
10
Operation and Maintenance Guidelines
To improve the service life of the air purier, please regularly maintain the device. Before
maintenance, ensure that the device is turned o and disconnected from the power supply. After
periodic use of the air purier, the lter will need to be replaced. The lter reset button on the
control panel will light up to signify that the lter needs replacement.
Place your air purier in a location with a good airow, not enclosed in an alcove or against
a wall. Additionally, avoid particularly damp or dusty locations as this will cause too much
wear and tear on the lters.
Avoid placing the device on soft or uneven surfaces to prevent vibration or noise during
operation. Leakage may also occur.
Do not place any objects inside the device, other than the proprietary lters, to avoid
internal or external damage.
If you shut down or do not use the device for a long period of time, disconnect it from the
power supply and place the device out of reach of children.
When the device is being moved or undergoing maintenance, turn it o and disconnect it
from the power supply to prevent re, electric shock or injury.
During maintanence, disconnect the device from the power supply to
avoid electrical shock or injury.
Clean appearance
When cleaning the air purier, please turn o the power supply and clean it with a soft
and clean dry cloth. Do not use alcohol, gasoline, benzene and other chemical solvents to
clean it.
EN
11
Air Filter Replacement
Air Filter Capacity
The air purier lters have an average lifespan of 3,000 operating hours. Once they reach
this limit, an alert light will illuminate on the control panel, indicating that the lters need to
be replaced.
Replacement Air Filter Vendor
Visit www.bluemyst.com to purchase air lter replacements,
or email customer support at [email protected]
Replacement Air Filter Installation
The air lters are not washable and must be replaced after
3,000 operating hours.
Open the back cover of the purier and remove the used lters from the device.
Remove the new lters from their plastic packaging.
Insert the thinner Composite Filter A into purier. The black, circle-textured active
carbon lter should face toward you, with the pull tab pointing outwards.
Insert the wider Composite Filter B into the purier. The white meshed antibacterial
lter should face toward you, with the pull tab pointing outwards.
Replace the back cover. Connect the device to the power supply, press the power
button, and press the lter key for 3 seconds. The lter indicator light should turn
o, and the screen will have been reset successfully.
Back cover
Composite
Filter A
Composite
Filter B
Device
EN
12
Troubleshooting
Status Possible reason Possible solution
Device
doesn’t work
Disconnected from
power supply or power
supply is turned o.
Too loosely plugged
into the power supply.
Rear cover may not be
in place.
Filter PE bag may be
dismantled.
Vent may be covered.
There may be a
continuous release of
odor near the inlet.
It may be time to
replace the tler.
Connect to the power
supply or turn on the
power supply.
Connect plug properly
in to the power supply.
Reinstall the rear
cover.
Remove the lter PE
bag and reinstall the
lter correctly.
Close the purier and
remove the vent cover.
Removing odors and
making the purier run
for a period of time.
The odor will gradually
disappear.
Replacing the lter.
When the purifying
begins, the sound
is dull and the wind
is insignicant.
The air outlet
has an unusual
smell.
EN
13
Warnings
Power line
Do not use power other than the rated voltage (220V50Hz),
otherwise it may cause re, electric shock or malfunction
etc.
No power lines should be processed, forcibly bent, drawn,
twisted, bundled or placed near high temperature objects.
Power line breakage may cause re, electric shock or
malfunction etc.
Do not place heavy objects or any other pressure on the
power line. Pressure may cause re, electric shock or
malfunction etc.
If the power cord or power plug is damaged, do not use
the air purier, otherwise it may cause re, electric shock,
short circuit or malfunction etc.
Do not use wet hands to plug in the power line.
Do not replace the power cord without authorization.
Please contact the Bluemyst maintenance service center
for any damage.
The dust on the power plug or socket should be cleaned
regularly. Too much dust and moisture can cause bad
insulation, which may cause re, electric shock or
malfunction etc.
Non-professional personnel should refrain from disassembling the
device without authorization to prevent the danger of electric shock.
When replacing the lter screen, disconnect the device from the power
supply rst.
If there is any malfunction, follow the instructions and troubleshooting
method. If the device malfunction persists, please contact Bluemyst
customer support.
WARNINGS
Other manuals for BA1180WK
1
Table of contents
Other bluemyst Air Cleaner manuals
