Bodyworx AENERGISER User manual

Magnetic Bike
Model No:
1
Retain this owner’s manual for future reference
Read and follow all instructions in this owner’s manual
Version A
AENERGISER
BODY WORX
BODY WORX

EXPLODE DRAWING
-02-

PARTS LIST AND TOOLS
-03-

ASSEMBLY INSTRUCTION
STEP 1
1. Prepare a clean area. Take the main
frame bike with all parts out of the
carton and put them on such area.
Check the parts with the parts list to
make sure there’s no missing part in the
carton.
2. Install the front stabilizer (42) with 2
carriage bolts (30), washers (35) and
nuts (33) by using the hand tools. Make
sure the transportation wheels are in
correct direction.
STEP 2
1. Assemble the Rear Stabilizer (31) with 2
carriage bolts (30), washers (35) and
nuts (33) by using the hand tools. Adjust
the end caps on the rear stabilizer to
set up a stable, balanced position.
-04-

ASSEMBLY INSTRUCTION
STEP 3
1. Assemble the base tube (34) to the
main frame with 5 screws (36) and 1 flat
washer (25) and 4 wave washers (35).
STEP 4
1. Assemble the straps onto the pedals as
the sketches. Adjust the ideal length of
the straps according to your size of
feet.
2. Install the left pedal (23L) to the left
crank arm and screw the right pedal
(23R) onto the right crank arm (Set the
pedal bolts counter-clock wise).
(Note: when assembling the straps to the
pedals, make sure the right strap to the
right pedal, there’s an “R” on both strap
and pedal and left strap to the left pedal,
there’s an “L” on both strap and pedal.)
-05-

ASSEMBLY INSTRUCTION
STEP 5
1. Release 4 Allen bolts (36) and wave
washers (35) which are pre-assembled
on the main frame (37).
2. Install the handlebar post (01) onto the
main frame (37). Turn the Tension
Control Knob back and forward to
make sure it is smoothly moving. If not,
re-assemble the tension control cables
(52, 55). Follow the instruction below to
assemble the tension cable.
3. Assemble the cables (53, 54) of the
exercise computer between the main
frame and the handlebar post.
4. Use bolt driver to fasten the Allen bolts
(36) and wave washers (35).
1. Draw the tension cable out of the
handlebar post. Make sure tension
knob is at 1 (minimum position).
2. Connect the tension cable head (a)
with the other cable head (b) by
pushing it into notch ©.Draw the tension
cable with the copper end (d) to insert
it to the metal bracket notch (e).
3. Fix the handlebar post (1) carefully to
the main frame (37) to avoid cutting off
the computer cable. Fasten the
handlebar post to the main frame with
4 Allen bolts (36) and wave washers
(35).
-06-

ASSEMBLY INSTRUCTION
STEP 6
1. Install the handlebar (03) onto the bracket of
the handlebar post (01). Make sure the pulse
cable is outside the top of the handlebar
post with the computer bracket (plate)
protruded on top.
2. Put the metal cover (04) pressing the
handlebar. Then fix handlebar with one flat
washer (07), one spring washer (12), and an
Allen bolt (11) to fasten them firstly and then
assemble the plastic cover to the handlebar
by washers (7 & 12) and bushing (09) and
T-knob (10).
3. Adjust the handlebar to be a suitable angle.
Fasten the Allen bolt (11) and T-knob (10)
securely.
Precaution:
Before using this bike, be sure that you have
fastened the Allen bolt (11) and T-knob (10) on
the handlebar. This is very important
STEP 7
1. Assemble the seat (24) to the seat post
(27) with 3 nuts (26) and washers (25).
2. Insert the seat post through the bellow (28)
into the base frame through the plastic
sleeve (29). Select the ideal height position
on the seat post. Insert the knob (29) into
the hole. Tighten fully the knob.
-07-

ASSEMBLY INSTRUCTION
STEP 8
1. Slide the computer (13) to bracket.
2. Plug in the cable between the
computer and the handelbar post.
3. Plug the cable of hand pulse sensor
(02) from handlebar into the computer.
-08-

7380D Computer Instruction Manual
Buttons:
1. MODE: Press the button to select functions, and hold this button to total reset all
function values
Fucntions:
1. RPM SPEED: Display exercise speed.
2. TIME: Record exercise time by counting up or down.
3. DISTANCE: Record exercise distance by counting up or down.
4. CALORIES: Record calories consumption during exercise.
5. PULSE: Display heart rate value. High limit could be set as a warning.
Operation:
1. Insert battery, full display with beeper 2 seconds.
2. Display wheel size for 1 second.
3. Press MODE function to see all function values.
4. Start exercise, and all function activated.
Note:
1. Display shut off it no any signal coming in for 4 minutes., press any button or
pedaling to turn on the display.
2. In case of improper display, please replace the battery.
-09-

-10-
* IMPORTANT SAFETY INFORMATIONS *
PLEASE FOLLOW THE SAFETY RULES BELOW TO AVOID INJURY AND/OR ACCIDENTS
1. KEEP THE BIKE AWAY FROM THE ACCESS OF CHIDLREN, DO NOT ALLOW THE
CHILDREN TO BE AROUND WHEN USING THE MACHINE.
2. DO NOT RIDE THE BIKE STANDING UP.
3. DO NOT RIDE WHILE WEARING LOOSE ROBES, LOOSE PANTS OR SKIRTS.
4. ALWAYS WEAR RUBBER SOE SHOES OR TENNIS SHOES WHEN RIDING.
5. PLACE THE BIKE ON A SMOOTH HARD SURFACE.
6. THE USER’S MAX WEIGHT IS 100 KGS.
7. THE BRAKING SYSTEM OF THE BIKE IS SPEED DEPENDENT.
8. THE FIELD OF APPLICATION IS FOR HOME USE.
9. BEFORE EACH USE, MAKE SURE THAT ALL OF THE FASTENERS ON THE UNIT ARE
TIGHTENED SECURELY. IF HAVE DEFECTIVE, KEEP THE EQUIPMENT OUT OF UNTIL
REPAIR.
10. THE BRAKE PAD IS MOST SUSCEPTIBLE TO WEAR. BEFORE USE, MAKE SURE IT HAVE
FUNCTION.
11. THE SAFETY LEVEL OF THE EQUIPMENT CAN BE MAINTAINED ONLY IF IT IS EXAMINED
REGULARLY FOR DAMAGE AND WEAR.
12. THIS BIKE NOT SUITS FOR THERAPEUTIC USE.

-11-
WARM-UP EXERCISE

BODYWORX
BODY WORX