Bogen NYQUIST NQ-P0100 User manual

NYQUIST Matrix Mixer Pre-Amp
NQ-P0100 Installation
The NQ-P0100 is a mixer pre-amplier that enables
microphone, AES3 digital, and line-level source
inputs to be integrated into a Nyquist system. These
input sources can then be routed to any endpoint
or group of endpoints on the network for paging or
audio distribution.
WARNING: To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture.
Avertissement: pour réduire le risque d’incendie ou de choc électrique, ne pas exposer cet appareil sous la
pluie et l’humidité.
The apparatus shall not be exposed to dripping or splashing and that no objects lled with liquids, such
as vases, shall be placed on apparatus.
L’appareil ne doit pas être exposé aux écoulements ou aux éclaboussures et aucun objet ne contenant de
liquide, tel qu’un vase, ne doit être placé sur l’objet.
The mains plug is used as disconnect device. The mains plug of apparatus should not be obstructed OR
should be easily accessed during intended use. To be completely disconnect the power input, the mains
plug of apparatus shall be disconnected from the mains.
La prise du secteur est utilisé pour déconnecter le système. La prise du secteur ne doit pas être obstruée ou
doit être facilement accessible pendant son utilisation. Pour être complètement déconnecté de l’alimenta-
tion d’entrée, la prise doit être débranchée du secteur.
Minimum distances 10cm around the apparatus for sufcient ventilation.
- 10cm distance minimale autour de l’appareil pour une aération sufsante
The ventilation should not be impeded by covering the ventilation openings with items, such as newspa-
pers, table-cloths, curtains, etc.
- il convient que l’aération ne soit pas gênée par l’obstruction des ouvertures d’aéra
No naked ame sources, such as lighted candles, should be placed on the apparatus.
- il convient de ne pas placer sur l’appareil de sources de ammes nues, telles que des bougies allumées
The use of apparatus in moderate climates.
- si l’appareil est destiné à être utilisé sous un climat tempéré.
Publication Number 740-00021C

1200 MacArthur Blvd. Suite 304, Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2018, Bogen Communications, Inc.
Notice
Every effort was made to ensure that the information in this manual was complete and accurate at the
time of printing; however, all information is subject to change.
Important Safety Information
WARNING: To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture.
Always comply with the following basic safety precautions when installing and using the unit:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Clean only with dry cloth.
6. DO NOT install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including ampliers) that produce heat.
This equipment is not suitable for use in locations where children are likely to be present.
Equipment is intended for use only in a restricted access area.

1200 MacArthur Blvd. Suite 304, Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2018, Bogen Communications, Inc.
7. DO NOT defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding-type plug has two blades and a
third grounding prong. The wide blade, or the third prong, are provided for your safety. If the
provided plug does not t into your outlet, consult an electrician for replacement of the
obsolete outlet.
8. Protect the power cord from being walked on and/or pinched, particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
9. Only use attachments/accessories which are specied by the manufacturer.
10. Unplug this apparatus during lightning storms or when unused for long periods of time.
11. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
WARNING:
The apparatus shall be connected to a mains socket outlet with
a protective earthing connection.
To reduce the risk of re or electric shock, do not expose this appara-
tus to rain or moisture.
The apparatus shall not be exposed to dripping or splashing and that
no objects lled with liquids, such as vases, shall be placed on the
apparatus.
Where the mains plug or an appliance coupler is used as the discon-
nect device, the disconnect device shall remain readily operable.

1200 MacArthur Blvd. Suite 304, Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2018, Bogen Communications, Inc.
Installation
To install the Nyquist Matrix Mixer Pre-Amp:
1. Either place the Matrix Mixer Pre-Amp on a shelf, or use the adjustable brackets to mount it on a
wall or in a rack.
2. Ensure the POWER switch is in the OFF position.
3. Attach and then plug in the AC line cord.
4. Connect the 10/100 network cable.
5. Toggle the POWER switch ON.
6. Connect the input devices to the XLR, screw-terminal connections, or both as needed.

1200 MacArthur Blvd. Suite 304, Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2018, Bogen Communications, Inc.
Viewing and Understanding LEDs
Two LEDs appear on the front of the Matrix Mixer
Pre-Amp. One is labeled POWER and appears
as solid red during initial power up, ashes green
during a boot sequence, and appears solid green
when fully booted.
The STATUS LED uses the following indicators to
provide information about the appliance:
• Flashing red – No network connection found.
• Solid blue – The Matrix Mixer Pre-Amp is in
an uninitialized state and is not associated to
a server. (The server may be in a discovery mode.)
• Solid green – The Matrix Mixer Pre-Amp is registered to a Nyquist server and is in normal operation.
• Flashing green – The Matrix Mixer Pre-Amp has an IP address but is not registered with the Nyquist
server.
• Solid red – The Matrix Mixer Pre-Amp needs to be rebooted or reset so that the Nyquist application can
resume.
• Flashing Blue – The Matrix Mixer Pre-Amp is updating.
Using the Reset Button
The Reset button allows you to restart the Matrix Mixer Pre-Amp or to reset
the appliance’s conguration settings to the factory default settings. For
more information about resetting conguration settings, refer to the
Nyquist Matrix Mixer Pre-Amp Conguration Manual.

1200 MacArthur Blvd. Suite 304, Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2018, Bogen Communications, Inc.
Compliance
NOTE: is equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
rules. ese limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a com-
mercial environment. is equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Limited Warranty, Exlusion of Certain Damages
e NQ-P0100 is warranted to be free from defects in materials and workmanship for ve (5) years from the date of sale to the original
purchaser. Any part of the product covered by this warranty that, with normal installation and use, becomes defective (as conrmed by
Bogen upon inspection) during the warranty period will be repaired or replaced by Bogen, at Bogen’s option, with new or refurbished
product, provided the product is shipped insured and prepaid to: Bogen Factory Service Department: 4570 Shelby Air Drive, Suite 11,
Memphis, TN 38118, USA. Repaired or replacement product(s) will be returned to you freight prepaid. is warranty does not extend
to any of our products that have been subjected to abuse, misuse, improper storage, neglect, accident, improper installation or have been
modied or repaired or altered in any manner whatsoever, or where the serial number or date code has been removed or defaced.
THE FOREGOING LIMITED WARRANTY IS BOGEN’S SOLE AND EXCLUSIVE WARRANTY AND THE PURCHASER’S SOLE AND
EXCLUSIVE REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, AND ALL
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND
EXCLUDED TO THE MAXIMUM EXTENT ALLOWABLE BY LAW. Bogen’s liability arising out of the manufacture, sale or supplying of
products or their use or disposition, whether based upon warranty, contract, tort or otherwise, shall be limited to the price of the product.
IN NO EVENT SHALL BOGEN BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, LOSS OF PROFITS, LOSS OF DATA OR LOSS OF USE DAMAGES) ARISING OUT OF THE MANUFACTURE,
SALE OR SUPPLYING OF PRODUCTS, EVEN IF BOGEN HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR
LOSSES. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you. is warranty gives you specic legal rights, and you may also have other rights which vary from State to State.
Products that are out of warranty will also be repaired by Bogen Factory Service Department -- same address as above or call 201-934-
8500, at owner’s expense. Returned products which do not qualify for warranty service, may be repaired or replaced at Bogen’s option with
a previously repaired or refurbished items. e parts and labor involved in these repairs are warranted for 90 days when repaired by the
Bogen Factory Service Department. All parts and labor charges as well as shipping charges will be at the owner’s expense.
All returns require a Return Authorization number. For most ecient warranty or repair service, please include a description of the failure.
11/2018