BOLERO DA695 User manual

DA695 Bolero Horizontal Changing station
DA696 Bolero Vertical Changing station
A4 size: Front page
Safety Tips
• The product is intended for the child age/weighted up to the
maximum of 12 months/ 11kgs.
• DO NOT use the changing unit if any part is broken, torn or
missing.
• All assembly fittings shall always be correctly tightened and checked
regularly.
• Warning: BE AWARE of the risk of an open fire or other sources of strong
heat such as electric bar fires, gas fires, etc., in the vicinity of the product.
• We recommend that for safe use of the product, the unit is installed to
brickwork or blockwork using fixings that are appropriate to the wall.
• We do not recommend fixing onto a toilet or changing room cubicle wall.
• If installing to a cavity wall then a sound fixing joist is also required.
• Any additional or replacement parts shall only be obtained from the
BOLERO agent.
• All recommended fixings are supplied. Do not use less substantial fittings.
We recommend the use of torque controlled power tool to fully tighten
the fixings. This ensures that the fixing plug opens and firmly grips the
substrate.
• This unit does not require a changing pad and therefore, no pad is supplied
with this product.
• Ensure that all fixings are checked and tightened as necessary. Protruding
fixings present the risk of clothing or accessories (e.g. strings, necklaces,
ribbons for babies, dummies, etc.) becoming entangled and exposing the
child to risk of injury.
• Units should be fitted no less than 100mm from the corner of the room to
facilitate cleaning.
• Keep all packaging away from children. Dispose of the packaging in
accordance with the regulations of local authorities.
• Be sure to check all packaging materials for any small parts that may have
come loose during transportation.
IMPORTANT: KEEP FOR FUTURE
REFERENCE. READ CAREFULLY.
WARNING: DO NOT leave
the child unattended.
Operation
• Before use: Make sure the changing tray is fully extended into its horizontal position.
• After use: Fold the tray into its upright position by lifting the front edge and carefully raising it to the vertical.
NOTE: If the tray is folded up with excessive force it may cause damage to the wall.
Cleaning, Care & Maintenance
Cleaning
• Clean with a damp cloth.
• For more stubborn stains a domestic cream cleaner can be used.
• Do not use any abrasive cloths, caustic or solvent cleaners as these may damage the product.
Care and Maintenance
• Open the unit and check that all wall mounting fixings are secure. Check that the changing tray does not rest
below the horizontal position.
• Any replacement parts must be obtained from BOLERO only.
Compliance
BOLERO parts have undergone strict product testing in order to comply with regulatory standards and specifications
set by international, independent, and federal authorities.
This product conforms to: EN12221: 2008+A1:2013
All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording or otherwise, without the prior written permission of BOLERO.
Every effort is made to ensure all details are correct at the time of going to press, however, BOLERO reserve the right to change
specifications without notice.
UK 0845 146 2887 Fourth Way, Avonmouth, Bristol,
BS11 8TB United Kingdom
DE 0800 – 1860806
NL 0800 – 29 1 29 IT N/A
040 – 2628080 ES 901-100 133
FR 0800 - 29 2 29 PT 901-100 133
01 60 34 28 80 AU 1300 225 960 15 Badgally Road, Campbelltown,
2560, NSW, Australia
DA695-DA696_A4_v1_180105.indd 1 2018/1/5 17:16

DA695-DA696_A4_v1_180105
A4 size: Back page
Pack Contents
The following is included:
A
DA695
DA696
x 1
Bx 5 Dx 5
Cx 5 Ex 5
Tools Required for
Assembly
(Not included)
Installation
1
370mm
Mark and drill 5 holes on the wall as illustrated.
Note: Ensure there is no electric/water pipe beneath
the holes.
185mm185mm
245mm 245mm
2
Insert the wall plugs into the drilled holes.
3
900mm
Insert a screw into the lower middle hole, leaving 10mm protruding from the
wall surface. Hang the changing station on the screw.
Warning: Please ensure this screw is fitted/tightened
first before the side screws to avoid deformation.
900mm
10mm
4
Mount the changing station onto the wall using
the 4 side screws and washers.
Cover the screws with screw caps.
5
Now the changing station is installed in place.
820mm
450mm
820mm
550mm
860mm
450mm
750mm
120mm
750mm
120mm
DA695-DA696_A4_v1_180105.indd 2 2018/1/5 17:16