BoLiving 519789 User manual

2020-07-03Rev 1 -
Java Console Table
519789

! Read instructions carefully. Check no parts are missing.
! Assemble the furniture on a soft level surface to avoid damaging the furniture or your floor.
! Carefully identify each component, especially those that are similar.
! The most common mistake is getting things back to front.
! Separate and identify each component from the hardware pack and rest each one in it's
proper location before fastening.
! We recommend furniture be assembled near where they will be placed, to avoid moving the
product unnecessarily once assembled.
! If there is a need to move the furniture, please remove all loose items and have extra hands
to help lift the furniture to the desired location. Dragging the furniture will damage both the
furniture and the floor.
! Regularly check and re-tighten (if necessary) all bolts on furniture that you have assembled
yourself.
WARNING
Keep these instructions for future reference
ALLOW 60 MIN
Page 2
Unit 1, Ubique Business Park, March Way, Battlefield, Shrewsbury, SY1 3JE
2 Persons Required
Tools Required
DO NOT USE ON PRODUCT
Rattan
Rattan is a natural material that will expand and contract with changes in the surrounding humidity
and temperature. Each rattan piece in the furniture may also respond to these changes to a different
degree. Once humidity and temperature return to normal, each rattan piece would also return to its
original shape. This is a natural phenomenon and not a defect.
Warning: Ensure the wall strap is attached to
avoid serious injury
To avoid any serious of fatal injury, a wall strap has been provided with this product to prevent
toppling. We strongly recommend that this product is permanently fixed to the wall or other suitable
surface. Fixing devices are not included since different surface materials require
different attachment. Please seek professional advice if you are in doubt of what fixing device to use.

Parts list
1 x Top Panel (P1)
2 x Bottom Panels (P2)
2 x Side Panels (P3)
1 x Divider Panel (P4)
1 x Back Panel (P5)
2 x Drawer Fronts (P6)
Top Panel (P1)
Page 3
Bottom Panel (P2)
Side Panel
(P3)
Back Panel
(P5)
Drawer Front
(P6)
Drawer Back
(P9)
Drawer Base
(P10)
Drawer Left
Side (P7)
Drawer Right
Side (P8)
Side Panel
(P3)
Divider Panel
(P4)
Drawer Front
(P6)
Drawer Support (P11)
(P7)
(P10)
(P9)
(P8)
(P11)
Leg
(P12)
Leg
(P12)
2 x Drawer Left Sides (P7)
2 x Drawer Right Sides (P8)
2 x Drawer Backs (P9)
2 x Drawer Bases (P10)
2 x Drawer Supports (P11)
4 x Legs (P12)

Page 4
Hardware Pack
24 x Cam Bolts
(H1)
12 x Big Cam
Nuts (H2)
12 x Dowels Ø8mm
(H3)
2 x Handles
(H4)
4 x Screws 16mm
(H6)
12 x Flat Washers
(H9)
8 x Spring
Washers (H10)
4 x Screws 28mm
(H11)
1 x Allen Key
(H12)
4 x Felt Feet
(H5)
8 x Bolts 55mm
(H8)
4 x Back Panel
Connectors (H7)
2 x Screws 25mm
(H14)
12 x Small Cam
Nuts (H15)
2 x Wall Strap
(H13)
4 x Dowels Ø6mm
(H16)
12 x Screws 38mm
(H17)
4 x Slides
(H19)
24 x Screws 12mm
(H18)

Step 1
Page 5
You will need
Attach 1 x felt foot (H5) onto each leg (P12) as shown.
Step 2
You will need
8 x Bolts
55mm (H8)
Attach leg (P12) onto bottom panel (P2),using 2 x bolts (H8), 2 x flat washers (H9)
and 2 x spring washers (H10).
Tighten the bolt with allen key (H12).
Repeat three times for all legs (P12).
Turn the assembled unit over.
(P12)
4 x Felt Feet
(H5)
X4
H5
8 x Flat
Washers (H9)
8 x Spring
Washers (H10)
1 x Allen Key
(H12)
(P12)
H12
H8
H9
H10
(P2)
(P12)
(P12)
(P12)
(P12)
(P2)

Step 3
Page 6
You will need
Step 4
You will need
(P2)
H1
Screw 6 x cam bolts (H1) into top panel (P1), using a phillips head screwdriver.
6 x Cam Bolts
(H1)
Phillips Head
Screwdriver
6 x Cam Bolts
(H1)
Phillips Head
Screwdriver
Screw 6 x cam bolts (H1) into bottom panel (P2), using a phillips head screwdriver.
H1
H1
H1
H1
H1
H1
H1
H1
H1
H1
H1
(P1)

Step 5
Page 7
You will need
Phillips Head
Screwdriver
6 x Screws
12mm (H18)
4 x Slides
(H19)
Mallet
H19
Separate the 4 sets of slide runners (H19-2) and
slide tracks (H19-1) from slides (H19) by following the steps below:
Extend the slide runner all the way forward.
Press the plastic release lever of the slide down and
pull the slide runner (H19-2) completely out.
H19
Slide runner H19-2 Slide track H19-1
Note the position
of the rubber stopper
Attach 2 x separated slide tracks (H19-1) onto side panels (P3) with 6 x screws (H18),
using a phillips head screwdriver as shown.
Pay attention to ensure the slides are in the correct direction as shown.
Insert 4 x dowels (H3) into each panel (P3) as shown.
Use a mallet to gently tap the dowels into place if needed.
H19-1
8 x Dowels
ø8mm (H3)
H18
(P3)
H3
H3
H3
H3
X2
H18
H18 H19-1
H19-1
H19-1
Adjust runner to access the screw holes.

Step 6
Page 8
You will need
Phillips Head
Screwdriver
6 x Screws
12mm (H18)
2 x Slide
Tracks (H19-1)
Mallet
H19-1
Note the position
of the rubber stopper
Insert 4 x dowels (H3) into divider panel (P4) as shown.
Use a mallet to gently tap the dowels into place if needed.
Attach 1 x slide track (H19-1) onto divider panel (P4) with 3 x screws (H18) as shown.
Turn divider panel (P8) over.
Attach 1 x slide track (H19-1) onto divider panel (P4) with 3 x screws (H18) as shown,
using a phillips head screwdriver.
Note the screw fixing hole is different to the first runner.
H19-1
4 x Dowels
30mm (H3)
H18
(P4)
H3
H18
Note the screw fixing
hole is different to
the first runner.
H19-1
H19-1
H3
H3
H3
H19-1
H19-1
H18
H18
H18
H18
(P4)

Step 7
Page 9
You will need
Position panels (P3) & (P4) onto bottom panel (P2) as shown.
Make sure the grooves in panels (P2) & (P3) are on the same side.
Insert 6 x big cam nuts (H2) into panels (P3) & (P4),
using a flat head screwdriver turn clockwise to lock.
Step 8
Slide back panel (P5)
into the grooves of the panels.
Flat Head
Screwdriver
6 x Big Cam
Nuts (H2)
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
(P2)
(P2)
(P5)
(P4)
(P3)
(P3)
(P3)
(P3)
Laminated
edge
H2
H2
H2
H2
H2
H2

Step 9
Page 10
You will need
Position top panel (P1)
onto panels (P3) & (P4) as shown.
Make sure the groove in
top panel (P1) is on the same side
as the back panel (P5).
Insert 6 x big cam nuts (H2)
into panel (P3) & (P4),
using a flat head screwdriver
turn clockwise to lock.
Step 10
Flat Head
Screwdriver
6 x Big Cam
Nuts (H2)
(P1)
(P4)
(P3)
(P3)
H2
H2
H2 H2
H2
H2
You will need
If necessary, gently adjust the top panel (P1) sideways in either direction
until XX and YY are equal.
Holding it in place, fix 4 x back panel connectors (H7) to assembled unit
with 4 x screws (H6) as shown, using a phillips head screwdriver.
Phillips Head
Screwdriver
4 x Screws
16mm (H6)
4 x Back Panel
Connectors (H7)
H7
H7
H6
(P5)
(P5)
(P1)
(P5)
XX
YY
XX=YY
XX
YY
(P1)
(P1)
H7
H7
H7
(P5)
(P1)
H7

Step 11
Page 11
You will need
Insert 1 x dowel (H16) into each panel (P7) & (P8) as shown.
Use a mallet to gently tap the dowels into place if needed.
Step 12
H16
You will need
X2
Mallet
4 x Dowels
30mm (H16) H16
(P7) (P8)
Position each drawer side (P7), (P8)
and drawer support (P11) onto drawer fronts (P6).
Insert 12 x small cam nuts (H15)
into drawer sides (P7), (P8) and drawer support (P11).
Turn small cam nuts to lock using a flat head screwdriver.
X2
(P8)
(P7)
(P11)
H15
H15
H15
(P6)
H1
H1
H1
H1
H1
Screw 6 x cam bolts (H1) each into drawer front (P6), using a phillips head screwdriver.
12 x Cam Bolts
(H1)
Phillips Head
Screwdriver
X2
Step 13
You will need
Flat Head
Screwdriver
12 x Small Cam
Nuts (H15)
(P6)

Step 14
Page 12
Step 15
You will need
Slide drawer base (P10) into the grooves of panels of drawer assembly.
X2
(P10)
12 x Screws
38mm (H17)
Phillips Head
Screwdriver
Attach drawer back (P9) to each drawer assembly with 6 x screws (H17),
using a phillips head screwdriver as shown.
X2
H17
(P7)
(P8)
(P11)
H17
H17
(P9)

Step 16
Page 13
You will need
Step 17
You will need
Attach 1 x slide runner (H19-2) to each drawer side (P7) and (P8) with 3 x screws (H18),
using a phillips head screwdriver as shown.
4 x Screws
28mm (H11)
Phillips Head
Screwdriver
2 x Handles
(H4)
Attach 1 x handle (H4) onto each drawer front (P6) with 2 x screws (H11),
using a phillips head screwdriver as shown.
4 x Slide
Runners (H19-2)
Phillips Head
Screwdriver
12 x Screws
12mm (H18)
H11
H19-2
(P7)
H19-2
H19-2
(P8)
X2
X2
H4
(P6)

Step 18
Page 14
Move inner ball bearing track
to front of slide track (H19-1).
H19-2
H19-1
Gently insert drawer slide runner
into ball bearing Track.
Position drawer so that slide runners (H19-2) align with slide tracks (H19-1) as shown.
Gently push drawer into the closed position.

Step 19
Page 15
You will need
Step 20
You will need
Fix 2 x wall straps (H13) to top panel (P1) with 2 x screws (H14)
and 2 x flat washers (H9) as shown, using a phillips head screwdriver.
(P1)
H13
H9
H14
H13
H14 H9
(P1)
H13
H9
H14
(P5)
(P5)
2 x Flat
Washers (H9)
2 x Screws
25mm (H14)
2 x Wall Straps
(H13)
Phillips Head
Screwdriver
2 x Flat
Washer (H9)
Phillips Head
Screwdriver
Seek advice from a qualified
trades person on how to
attach this wall strap to
your specific wall.
Screw and wall plug are
not included.
Please use appropriate
fixtures for your wall.
Move the console table to the final position.
Attach the wall strap to the wall.
Make sure they are firmly attached and fit snugly .
H9
Wall
Screw
We strongly recommend
that this product is permanently
fixed to the wall
or other suitable surface.

Step 21
Page 16
Job complete!
In the interest of our environment please dispose
of all packaging thoughtfully.