Hallowell ROOKIE KD SPORT User manual

ROOKIE KD SPORT/GEAR LOCKER
ASSEMBLY INSTRUCTIONS
General Instructions
1. Check material received against the packing list. First, check the number of
packages received and then check the contents of each package.
2. Check the material received for damage. If damage has occurred, secure a
“damage notation” from the carrier
3. Identify each part as it is unpacked and put like parts together as close as possible
to the working area where they are to be assembled.
4. Be careful to use the correct hardware as specified in the assembly instructions.
CAUTION
In the interest of safety, all lockers must be securely anchored to the floor and/or wall.
For safety, handle all components carefully and wear work gloves when assembling
lockers. Install all units plumb and tighten all hardware securely. Retain instruction for
future reference.
866-566-0500
[email protected]
www.Hallowell-List.com

6
4
3
9
13
8
14
7
16
1
10
12
11
5
15
21
2
23
22
ROOKIE COMPONENTS
PART NUMBER DESCRIPTION
8/QT
Y.
1 UWB12422FL-KD B W/FOOT LOCKER
1
2 ULP2272DP-PS-KD PRO-SPORT LEFT PANEL
1
3 URP2272DP-PS-KD PRO-SPORT RIGHT PANEL
1
4 UFT12422PS-KD PREP SPORT FLAT TOP
1
5 UFS2422PS-B-KB PRO SPORT FULL SHELF
1
6 URP2212PS-B PRO-SPORT RIGHT PANEL
1
7 PSSF24-KD PRO-SPORT SEAT FRONT
1
8 PSFS2422-KD1 PRO SPORT SEAT
1
9 PH22
1
10 SFS22-KD SEAT SUPPORT
2
11 AKD1272-6PL BOX DOOR
1
12 PH11 11" PIANO HINGE
1
13 PSSR2422-KD1 PRO SPORT SEAT REAR
1
14 UBP2472PS-KD BACK PANEL
1
15 KBLH101-KD KD BOX DOOR LATCH HOOK
1
16 BEC22 BASE END CAP
2
17 RB2071
2
18 UHS2422PS-KD SEAT/SHELF
1
19 UHS2422PS SEAT/SHELF
1
20 90276A240
63
21 KBLP100 KD BOX DOOR PULL
1
22 TRH200 TOWEL ROD HOLDER
2
23 KCR24 COAT ROD
1
THIS DRAWING AND THE INFORMATION ON IT IS THE CONFIDENTIAL PROPERTY OF HALLOWELL. AND SHALL NOT BE COPIED OR DISCLOSED TO OTHERS WITHOUT WRITTEN
PERMISSION. ONLY HALLOWELL RESERVES THE RIGHT TO ALTER ANY DESIGN. ANY UNAUTHORIZED MODIFICATIONS RELEASES HALLOWELL FROM ALL LIABILITIES.
www.Hallowell-List.com
1
:
SHEET DRAWING NO. PART NO.
DESCRIPTION
REV. SCALE DATE
DATE
DATE
APPROVED BY
DRAWN BY
CHECKED BY
2823 W. ORANGE AVE. Tel [phone]
APOPKA, FLORIDA 32703 Fax [phone]
FRACTIONAL
X/X. ± 1/64
UNLESS OTHERWISE
SPECIFIED ALL
DIMENSIONS ARE IN
INCHES. METRIC
DIMENSIONS WILL BE
WITHIN [XX]
ANGULAR
± 1/2°
INCHES
XX. ± .010
XXX. ± .005
TOLERANCES
UNLESS OTHERWISE
SPECIFIED
SA1563-1
ROOKIE
ASSEMBLY
5/23/2012 JIL
1
OF

STEP 1
2
3
5
14
Slot for side panel to
come out at the
bottom.
3. Place top. The back
of the top goes over the
back panel. Align holes
and bolt.
4. Place bottom and align
holes with side and back panel.
Place side caps inside the bottom
and bolt bottom and side caps to
side panel.
4
16
1
Bolt shelf to side 1.
panels making sure the
shelf tab goes into the
side panel.
Bolt both coat rod
holders to the shelf with
the coat rod in them.
Tab
23
22
STEP 2
STEP 3
Final Product
2. Slide back
panel in between the
edges of the side panels.
Align hole and finger
tighten the bolts.
PRO SPORT ASSEMBLY
SA1563-2

1.Bolt side supports to
side panels.
2. Place back suppor on top
of the side support and
against the back with hinge
side facing forward. Bolt to
side supports.
Have a person insert the bolts
through the back in order to bolt
back support to back panel.
13
10
8
7
3. Bolt seat to the hinge
located on the back support
4. Insert front support
and set in between frame
and side support.
5. Slide to the bottom and
bolt to side panels and bottom
of unit.
FOOT LOCKER KIT
SA1563-3

Bolt divider to the shelf. 1.
Place the top and bolt 2.
to divider and side panels.
4
6
4. Bolt door to outside of divider.
5. Bolt finger pull to the inside of
the door.
21
11
3. Place latch inside
the side flange of the
panel and bolt to panel.
15
STEP 1 STEP 2 STEP 3
SECURITY BOX INSTALLATION
SA1563-4