BoLiving 519283 User manual

2020-07-03Rev 1 -
Niva TV Unit
519283

! Read instructions carefully. Check no parts are missing.
! Assemble the furniture on a soft level surface to avoid damaging the furniture or your floor.
! Carefully identify each component, especially those that are similar.
! The most common mistake is getting things back to front.
! Separate and identify each component from the hardware pack and rest each one in it's
proper location before fastening.
! We recommend furniture be assembled near where they will be placed, to avoid moving the
product unnecessarily once assembled.
! If there is a need to move the furniture, please remove all loose items and have extra hands
to help lift the furniture to the desired location. Dragging the furniture will damage both the
furniture and the floor.
! Regularly check and re-tighten (if necessary) all bolts on furniture that you have assembled
yourself.
WARNING
Keep these instructions for future reference
ALLOW 60 MIN
Page 2
Unit 1, Ubique Business Park, March Way, Battlefield, Shrewsbury, SY1 3JE
2 Persons Required
Tools Required
DO NOT USE ON PRODUCT

Parts list
Box 1: Top Panel (P1); Left Side Panel (P2); Right Side Panel (P3); 4 x Leg (P5); Lower Divider Panel (P9);
2 x Drawer Left Side (P11); 2 x Drawer Right Side (P12); 2 x Drawer Back (P13); 2 x Drawer Base (P14);
2 x Drawer Rail (P15); Drawer Front (P16); Drawer Front (P17); Big Middle Leg (P18);
Small Middle Leg (P19); Hardware Pack.
Box 2: 2 x Short Rail (P6); 2 x Long Rail (P7); Upper Divider Panel (P8); Shelf (P10); Back Panel (P20).
Top Panel (P1)
Page 3
Shelf (P10)
Left Side
Panel (P2)
Right Side Panel
(P3)
Bottom Panel (P4)
Leg (P5)
Leg (P5)
Leg (P5)
(P5)
Short Rail
(P6)
Short Rail
(P6)
Long Rail (P7)
Long Rail (P7)
Upper Divider
Panel (P8)
Lower Divider
Panel (P9)
Drawer Left
Side (P11)
Drawer Right
Side (P12)
Drawer Back (P13)
Drawer Base (P14)
Drawer Rail (P15)
(P11)
Drawer Front (P16)
(P15)
(P14)
(P13)
Drawer Front (P17)
(P12)
Big Middle
Leg (P18)
Small Middle
Leg (P19)
Back Panel (P20)

Page 4
Hardware Pack
57 x Cam Bolts
(H1)
45 x Big Cam
Nuts (H2)
44 x Dowels
(H3)
12 x Small Cam
Nuts (H4)
24 x Screws
(H6)
#6x12 mm
4 x Screws
(H9)
#10x38 mm
1 x Adjustable
Foot (H10)
19x Screws
(H5)
#10x38 mm
4 x Felt Feet
(H8)
4 x Slides
(H7)

Step 1
Page 5
You will need
13 x Cam bolts
(H1)
Screw 13 x cam bolts (H1) into bottom panel (P4) as shown,
tighten with a Phillips head screwdriver.
Step 2
Phillips head
screwdriver
You will need
14 x Dowels
(H3) Mallet
Insert 3 x dowels (H3) into each short rail (P6) as shown.
Insert 4 x dowels (H3) into each long rail (P7) as shown.
Use a mallet to gently tap the dowels into place if needed.
(P4)
H1
(P7)
(P6)
H1
H1
H1
H1
H1
(P6)
(P7)
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H1
H1
H1 H1
H1
H3
H3

Step 3
Page 6
You will need
8 x Cam bolts
(H1)
Screw 2 x cam bolts (H1) into each leg (P5) using a Phillips head screwdriver.
Attach 1 x felt foot (H8) onto each leg (P5) as shown.
Step 4
Phillips head
screwdriver
You will need
4 x Big cam
nuts (H2)
Fit each short rail (P6) between 2 x legs (P5).
Insert 2 x big cam nuts (H2) each into short rail (P6).
Using a flat head screwdriver, turn the big cam nuts (H2) clockwise to lock.
4 x Felt feet
(H8)
(P5)
H1
H1
H8
X4
Flat head
screwdriver
H2
(P5)
(P6) (P5)
(P5)
(P5)
(P6)
H2
H2
H2
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.

Step 5
Page 7
You will need
Position 2 x long rails (P7) between the assembled units as shown.
Insert 4 x big cam nuts (H2) into long rails (P7), using a flat head screwdriver
turn clockwise to lock.
Step 6
You will need
10 x Big cam
nuts (H2)
Position the leg assembly onto bottom panel (P4), making sure the cam bolts on
the bottom panel (P4) are inserted into the holes on the leg assembly.
Insert 10 x big cam nuts (H2) into short rails (P6) and long rails (P7),
using a flat head screwdriver turn clockwise to lock.
Carefully turn the unit over.
Flat head
screwdriver
Flat head
screwdriver
4 x Big cam
nuts (H2)
(P5)
(P7)
(P7)
H2
H2
H2
(P5)
(P5)
(P5)
(P7)
(P7)
(P4)
(P6)
(P6)
H2
H2
H2
H2 H2

Step 7
Page 8
You will need
Step 8
You will need
Insert 2 x dowels (H3) into small middle leg (P19) and big middle leg (P18).
Attach small middle leg (P19) to big middle leg (P18) with 1 x screw (H5),
tighten with a Phillips head screwdriver.
Position middle legs (P18) & (P19) to bottom panel (P4).
Insert 3 x big cam nuts (H2) into middle legs (P18) & (P19), and turn clockwise to lock
using a flat head screwdriver.
Screw 1 x adjustable foot (H10) into big middle leg (P18) as shown.
H3
H5
(P19) (P18)
(P19)
(P18)
H3
2 x Dowels
(H3)
Phillips head
screwdriver
1 x Screw
(H5)
1 x Adjustable
foot (H10)
3 x Big cam
nuts (H2)
Flat head
screwdriver
(P4)
(P18) (P19)
H10
#10x38 mm
H2
H2

Step 9
Page 9
You will need
Screw 6 x cam bolts (H1) into bottom panel (P4) as shown,
tighten with a Phillips head screwdriver.
Screw 4 x screws (H9) into bottom panel (P4), tighten with a Phillips head screwdriver.
Step 10
You will need
Phillips head
screwdriver
Phillips head
screwdriver
Screw 6 x cam bolts (H1) into top panel (P1), tighten with a Phillips head screwdriver.
6 x Cam bolts
(H1)
6 x Cam bolts
(H1)
4 x Screws
(H9)
H1
H9
(P1)
H1
H1
H1
H1
H1
H1
H9
H9
H9
(P4)
#10x38 mm
H1
H1
H1
H1
H1

Step 11
Page 10
You will need
Insert 4 x dowels (H3) into upper divider panel (P8) as shown.
Insert 4 x dowels (H3) into shelf (P10) as shown.
Insert 8 x dowels (H3) into back panel (P20) as shown.
Use a mallet to gently tap the dowels into place if needed.
Screw 4 x cam bolts (H1) into shelf (P10) using a Phillips head scredriver.
Phillips head
screwdriver
4 x Cam bolts
(H1)
16 x Dowels
(H3)
(P8)
Mallet
H3
H3
H3
H3
(P10)
H1
H3
H3
H3
H3
H1 H1
H1
(P20)
H3
H3
H3
H3
H3
H3
H3
H3

Step 12
Page 11
You will need
8 x Cam bolts
(H1)
Phillips head
screwdriver
H7
Separate the 4 sets of slide runners (H7-2) and
slide tracks (H7-1) from slides (H7) by following the steps below:
Extend the slide runner all the way forward.
Press the plastic release lever of the slide down and
pull the slide runner (H7-2) completely out.
6 x Screws
(H6)
4 x Slides
(H7)
H7
H7-1
Slide runner H7-2 Slide track H7-1
H7-1
H7-1
Note the position
of the rubber stopper
Attach 2 x separated slide tracks (H7-1) onto side panels (P2) & (P3) with 6 x screws (H6),
using a Phillips head screwdriver as shown.
Pay attention to ensure the slide are in correct direction as shown.
Screw 8 x cam bolts (H1) into side panels (P2) & (P3),
using a Phillips head screwdriver as shown.
Insert 8 x dowels (H3) into side panels (P2) & (P3) as shown.
Use a mallet to gently tap the dowels into place if needed.
Adjust runner to access the screw holes.
(P2)
H3
8 x Dowels
(H3) Mallet
(P3)
H3 H3
H3
H3
H3
H3
H3
H1
H1 H1
H1
H1
H1
H7-1
H7-1
H6
H6
H6
H6
H6
H6
#6x12 mm
H7-1 H7-1
Note the position
of the rubber stopper

Step 13
Page 12
You will need
Insert 4 x dowels (H3) into divider panel (P9).
Use a mallet to gently tap the dowels
into place if needed.
Attach 1 x slide track (H7-1) onto divider panel (P9) with 3 x screws (H6).
Turn divider panel (P8) over.
Attach 1 x slide track (H7-1) onto divider panel (P9) with 3 x screws (H6)
using a Phillips head scredriver.
Step 14
You will need
Phillips head
screwdriver
Attach upper divider panel (P8) to shelf (P10) with 2 x screws (H5) using a Phillips
head screwdrive.
6 x Screws
(H6)
4 x Dowels
(H3)
Phillips head
screwdriver
2 x Screws
(H5)
Mallet
#10x38 mm
(P8)
(P10)
H5
H5
#6x12 mm
2 x Slide
tracks (H7-1)
Note the position
of the rubber stopper
H7-1
H7-1
Note the screw fixing
hole is different to
the first runner.
H6
H6
H6
H6
H3 H6
H6
H3
H3
H3
(P9)
(P9)
H7-1
H7-1
Laminated
edge
First hole
from back
Second hole
from back

Step 16
Page 13
You will need
Attach lower divider panel (P9) to back panel (P20) with 2 x screws (H5) using a Phillips head
screwdriver as shown.
Step 17
You will need
Phillips head
screwdriver
Attach back panel (P20) and lower divider panel (P9) onto shelf (P10) as shown.
Insert 4 x big cam nuts (H2) into panels (P9) & (P20), turn clockwise to lock
using a flat head screwdriver.
2 x Screws
(H5)
#10x38 mm
Laminated
edge
(P20)
(P9)
These hole are facing up
H5
Round corner
Flat head
screwdriver
4 x Big cam
nuts (H2)
(P9)
(P10)
(P20)
H2 H2
H2
H2

Step 17
Page 14
You will need
Position left side panel (P2) to assembled unit as shown.
Insert 4 x big cam nuts (H2) into panels (P10) & (P20).
Turn clockwise to lock using a flat head screwdriver.
Step 18
You will need
Position right side panel (P3) to assembled unit as shown.
Insert 4 x big cam nuts (H2) into panels (P10) & (P20).
Turn clockwise to lock using a flat head screwdriver.
Flat head
screwdriver
4 x Big cam
nuts (H2)
H2
Flat head
screwdriver
4 x Big cam
nuts (H2)
(P20)
(P10)
(P2)
H2
(P3)
(P20)
(P10)
H2
H2

Step 19
Page 15
You will need
Position assembled unit
onto bottom panel (P4)
as shown.
Insert 6 x big cam nuts (H2)
into panels (P2) , (P3) & (P20),
turn clockwise to lock
using a flat head screwdriver.
Step 20
You will need
Position top panel (P1) to
assembled unit as shown.
Insert 6 x big cam nuts (H2)
into panels (P2), (P3) & (P8), turn clockwise to lock using a flat head screwdriver.
Phillips head
screwdriver
Flat head
screwdriver
6 x Big cam
nuts (H2)
(P2)
(P3)
(P20)
(P4)
(P9)
Fasten lower divider panel (P9)
with 2 x screws (H5) through
the bottom panel (P4)
using a Phillips head screwdriver.
Step 21
You will need
Flat head
screwdriver
6 x Big cam
nuts (H2)
(P1)
(P9) (P4)
H5
H5
2 x Screws
(H5)
#10x38 mm
H2
(P2) (P3)
(P8)
H2
H2
H2
H2
H2
H2
H2
H2 H2
H2
H2

Step 22
Page 16
You will need
Step 23
You will need
Screw 6 x cam bolts (H1) into each drawer fronts (P16) and (P17),
using a Phillips head screwdriver as shown.
12 x Cam bolts
(H1)
Phillips head
screwdriver
H1
H1
H1
H1
H1
H1 (P16)
(P17)
Position each drawer sides (P11), (P12) and drawer rail (P15) onto drawer fronts (P16) and (P17).
Insert 12 x small cam nuts (H4) into drawer sides (P11), (P12) and drawer rails (P15).
Turn small cam nuts to lock using a flat head screwdriver.
Flat head
screwdriver
12 x Small cam
nuts (H4)
(P16) (P17)
(P11)
(P12)
(P11)
(P12)
(P15) (P15)
H4
H4
H4
H4
H4 H4

Step 24
Page 17
You will need
Step 25
You will need
Phillips head
screwdriver
12 x Screws
(H5)
X2
(P12)
(P11)
(P15)
(P14)
Slide drawer base (P14) into
the grooves of panels of drawer assembly.
Attach drawer back (P113) to each drawer assembly with 6 x screws (H5),
using a Phillips head screwdriver as shown.
#10x38 mm
(P13)
H5
H5
H5
X2
4 x Slide
runners (H7-2)
Phillips head
screwdriver
12 x Screws
(H6)
H7-2
(P12)
(P11)
X2
H7-2
H7-2
H6
H6
H6
H6
H6
H6
Attach 1 x slide runners (H7-2) to each drawer sides (P12) and (P11) with 3 x screws (H6),
using a Phillips head screwdriver as shown.
H7-2
H7-2
#6x12 mm

Step 26
Page 18
Move inner ball bearing track
to front of slide track (H7-1).
(P16)
H7-2
H7-1
Gently insert drawer slide runner
into ball bearing Track.
Position drawer so that slide runners (H7-2) aligns with slide tracks (H7-1) as shown.
Gently push drawer into the closed position.
(P17)

Step 27
Job complete!
In the interest of our environment please dispose
of all packaging thoughtfully.
Page 19