BOMBARDIER SEA-DOO SPX 5838 1998 Install guide

Legal deposit:
National Library of Quebec
National Library of Canada
All rights reserved. No parts of this manual may be
reproduced in any form without the prior written
permission of Bombardier Inc.
©Bombardier Inc. 1998
Printed in Canada
®*Registered trademarks of Bombardier Inc.
Loctite®is a trademark of Loctite Corporation
Snap-on®is a trademark of Snap-on Tools Corporation
Gelcote®is a trademark of Gelcote International Limited

I
SECTION SUBSECTION PAGE
SAFETY NOTICE................................................................................................................................... III
WHAT’S NEW ....................................................................................................................................... IV
INTRODUCTION ................................................................................................................................... V
01 SERVICE TOOLS
AND PRODUCTS
01 - Mandatory service tools............................................................ 01-01-1
02 - Optional service tools................................................................ 01-02-1
03 - Service products ....................................................................... 01-03-1
02 MAINTENANCE 01 - Table of contents ...................................................................... 02-01-1
02 - Periodic inspection chart........................................................... 02-02-1
03 - Flushing and lubrication............................................................. 02-03-1
04 - Water-flooded engine................................................................ 02-04-1
05 - Storage...................................................................................... 02-05-1
03 TROUBLESHOOTING 01 - Troubleshooting ........................................................................ 03-01-1
04 ENGINE 01 - Table of contents ...................................................................... 04-01-1
02 - Leak test ................................................................................... 04-02-1
03 - Removal and installation ........................................................... 04-03-1
04 - Magneto system....................................................................... 04-04-1
05 - Top end ..................................................................................... 04-05-1
06 - Bottom end ............................................................................... 04-06-1
07 - Rotary valve............................................................................... 04-07-1
08 - Exhaust system......................................................................... 04-08-1
05 COOLING SYSTEM 01 - Table of contents ...................................................................... 05-01-1
02 - Circuit, components and care ................................................... 05-02-1
06 FUEL SYSTEM 01 - Table of contents ...................................................................... 06-01-1
02 - Fuel circuit................................................................................. 06-02-1
03 - Air intake ................................................................................... 06-03-1
04 - Carburetor ................................................................................. 06-04-1
07 LUBRICATION
SYSTEM
01 - Table of contents ...................................................................... 07-01-1
02 - Oil injection system................................................................... 07-02-1
03 - Oil injection pump ..................................................................... 07-03-1
08 ELECTRICAL
SYSTEM
01 - Table of contents ...................................................................... 08-01-1
02 - Ignition system.......................................................................... 08-02-1
03 - Charging system ....................................................................... 08-03-1
04 - Starting system......................................................................... 08-04-1
05 - Instruments and accessories .................................................... 08-05-1
06 - Digitally encoded security system ............................................ 08-06-1
09 PROPULSION
SYSTEM
01 - Table of contents ...................................................................... 09-01-1
02 - Jet pump................................................................................... 09-02-1
03 - Drive system............................................................................. 09-03-1
04 - Reverse system ........................................................................ 09-04-1
05 - Variable trim system ................................................................. 09-05-1
TABLE OF CONTENTS
GTX RFI

II
10 STEERING SYSTEM 01 - Table of contents...................................................................... 10-01-1
02 - SPX model ................................................................................ 10-02-1
03 - GTS model................................................................................ 10-03-1
04 - GS, GSX Limited, GTI and GTX Limited.................................... 10-04-1
05 - XP Limited ................................................................................ 10-05-1
06 - Alignment ................................................................................. 10-06-1
11 SUSPENSION 01 - Table of contents...................................................................... 11-01-1
02 - Direct action suspension .......................................................... 11-02-1
12 HULL/BODY 01 - Table of contents...................................................................... 12-01-1
02 - Adjustment and repair .............................................................. 12-02-1
13 TECHNICAL DATA 01 - SPX model ................................................................................ 13-01-1
02 - GS and GSX Limited ................................................................. 13-02-1
03 - XP Limited ................................................................................ 13-03-1
04 - GTS model................................................................................ 13-04-1
05 - GTI and GTX Limited................................................................. 13-05-1
14 WIRING DIAGRAMS 01 - Wiring diagrams........................................................................ 14-01-1
TABLE OF CONTENTS
GTX RFI

III
SAFETY NOTICE 0
This manual was primarily published to be used by watercraft technicians trained by the manufactur-
er who are already familiar with all service and maintenance procedures relating to Bombardier made
Sea-Doo watercraft.
Please note that the instructions will apply only if proper hand tools and special service tools are used.
It is understood that this manual may be translated into another language. In the event of any discrepan-
cy, the English version shall prevail.
The content depicts parts and/or procedures applicable to the particular product at its time of manufac-
ture. It does not include dealer modifications, whether authorized or not by Bombardier, after manufac-
turing the product.
The use of Bombardier parts is most strongly recommended when considering replacement of any com-
ponent. Dealer and/or distributor assistance should be sought in case of doubt.
Torque wrench tightening specifications must be strictly adhered to. Locking devices (ex.: locking disk,
lock nut) must be installed or replaced with new ones, where specified. If the efficiency of a locking
device is impaired, it must be renewed.
This manual emphasizes particular information denoted by the wording and symbols:
NOTE: Indicates supplementary information needed to fully complete an instruction.
Although the mere reading of such information does not eliminate the hazard, your understanding of the
information will promote its correct use. Always use common shop safety practice.
This information relates to the preparation and use of Bombardier watercraft and has been utilized safely
and effectively by Bombardier Inc. However, Bombardier Inc. disclaims liability for all damages and/or
injuries resulting from the improper use of the contents. We strongly recommend that any services be
carried out and/or verified by a highly skilled professional technician. It is understood that certain modifi-
cations may render use of the watercraft illegal under existing federal, provincial and state regulations.
◆WARNING
Identifies an instruction which, if not followed, could cause serious personal injury including
possibility of death.
-CAUTION
Denotes an instruction which, if not followed, could severely damage watercraft components.
SAFETY NOTICE

IV
WHAT’S NEW 0
SERVICE TOOLS AND PRODUCTS 01
• Complete new section.
MAGNETO SYSTEM 04-04
• New procedure to lock crankshaft on the 947 engine.
REMOVAL AND INSTALLATION 04-03
• New service tool for engine alignment procedure.
TOP END 04-05
• New service tool to extract the piston pin for all engines.
• New piston/cylinder wall and ring end gap clearances.
• New service tool to install dogleg circlip on the 947 engine.
• New RAVE valve adjustment on the 787 engine.
BOTTOM END 04-06
• New service tools for PTO flywheel removal and installation on the 947 engine.
CARBURETOR 06-04
• Carburetors on the 947 engine are rotated 180°. There is a new calibration and the diaphragms are
opened all the time to the atmosphere. There is no more need for a throttle position switch, amplifier
and solenoid.
• Use of Loctite 242 (blue) to carburetor mounting screws is replaced by Loctite 577 on all models.
OIL INJECTION PUMP 07-03
• New oil injection pump cable for the 947 engine.
IGNITION SYSTEM 08-03
• New testing procedures using a multimeter.
CHARGING SYSTEM 08-04
• New testing procedures using a multimeter.
WHAT’S NEW

V
INTRODUCTION 0
This Shop Manual covers BOMBARDIER made
SEA-DOO®watercraft models SPX 5838/5839,
GS 5626/5844, GSX Limited 5629/5845, XP Limit-
ed 5665/5667, GTS 5819, GTI 5836/5841and GTX
Limited 5837/5842.
HULL IDENTIFICATION NUMBER
(H.I.N.)
SPX and GTS Models
It is located at right hand rear side of hull.
1. Hull Identification Number (H.I.N.)
All Other Models
It is located on floorboard at the rear of the water-
craft.
1. Hull Identification Number (H.I.N.)
All Models
The Hull Identification Number is composed of 9
digits:
ENGINE IDENTIFICATION
NUMBER (E.I.N.)
717 Engine
The Engine Identification Number is located on
the upper side of the magneto housing.
TYPICAL
1. Engine Identification Number (E.I.N.)
F01L8XA
1
F08L0QA
1
Z Z N 1 2 3 4 5 L 4 9 5
Model year
Serial
number*
*
A letter may also be used as a digit.
F00A0CA
Month of production
Year of production
*
A letter may also be used as a digit.
1
F01D01A
INTRODUCTION

VI
787 Engine
The Engine Identification Number is located on
the upper crankcase on PTO side.
1. Engine Identification Number (E.I.N.)
947 Engine
The Engine Identification Number is located on
the upper crankcase on MAGNETO side.
1. Engine Identification Number (E.I.N.)
ARRANGEMENT OF THIS
MANUAL
The manual is divided into 14 major sections:
01 SERVICE TOOLS AND PRODUCTS
02 MAINTENANCE
03 TROUBLESHOOTING
04 ENGINE
05 COOLING SYSTEM
06 FUEL SYSTEM
07 LUBRICATION SYSTEM
08 ELECTRICAL SYSTEM
09 PROPULSION SYSTEM
10 STEERING SYSTEM
11 SUSPENSION
12 HULL/BODY
13 TECHNICAL DATA
14 WIRING DIAGRAMS
Several sections are divided in various subsec-
tions. There is a table of contents at the beginning
of many sections.
F01D87A 1
F06D15A 1
INTRODUCTION

VII
Section 03 ENGINE
Subsection 04 (MAGNETO SYSTEM)
MAGNETO SYSTEM
717 Engine
03-04-1
F01D4WS
12 11
5 N•m
(44 lbf•in)
13 9 N•m
(80 lbf•in)
Loctite
242
4
68Loctite
242
7
6 N•m
(53 lbf•in)
Loctite
242
6 N•m
(53 lbf•in)
9
Loctite
242
5
6 N•m
(53 lbf•in)
3
14
Loctite
242
4
Loctite
648
10
15
145 N•m
(107 lbf•ft)
Anti-seize
lubricant 2
9 N•m
(80 lbf•in)
1
Page heading
indicates section
and subsection
detailed.
Tightening torque nearby fastener.
In this case, nut must be torqued to
145 N•m (107 lbf•ft).
Exploded view assits
you in identifying
parts and related
positions.
TYPICAL PAGE
F01A09S
Illustration number
for publishing
process.
Subsection title
indicates
beginning of the
subsection.
Dotted box
contains parts of
a particular
model or an
exploded view.
Page numbering system:
03: ENGINE section
04: MAGNETO SYSTEM subsection
1: First page of this subsection
Italic sub-title
above exploded
view indicate
pertaining models.
Drop represents
a liquid product
to be applied to a
surface. In this case
Loctite 242 to
screw threads.
Bold face number
indicates special
procedure
concerning this part.
Pay attention to torque specifi-
cations. Some of these are in
lbf•in instead of lbf•ft. Use appro-
priate torque wrench.
CAUTION
▼
INTRODUCTION

VIII
1
2
Section 06 FUEL SYSTEM
Subsection 03 (CARBURETORS)
06-03-4
Step : Install pump gauge tester to pulse nipple
Step : Pump tester until it reaches the desired pressure
1. Fuel outlet nipple
2. Fuel inlet nipple
A. 28 kPa (4 PSI)
3, Diaphragm
XP Model Only
CARBURETOR REMOVAL
Inspect parts for corrosion dammage (shaft, butterfly,
spring screw, check valve housing, etc.).
PUMP DIAPHRAGM LEAK TEST
TYPICAL
To remove carburetors from engine, proceed as fol-
lows:
Remove air vent tube support.
Unlock retaining slides holding air intake silencer base.
Remove air intake silencer base from watercraft.
Remove screws holding flame arrester base support
to cylinder head cover.
Unscrew base retaining screws then remove base from
carburetors and move to front of watercraft.
Turn the valve to OFF position.
NOTE: For fuel line removal, use pliers (P/N 295
000 054).
Disconnect pulse line from fuel pump.
Disconnect fuel fuel supply line from fuel pump.
Disconnect fuel return line.
Disconnect oil injection pump cable, throttle cable and
choke cable.
Remove screws no. 6 and lock washers no. 7 retaining
carburetors.
All Others Models
Remove 4 bolts no. 8 and lock washers no. 12 from
rotary valve cover then move carburetors and rotary
valve cover on top of engine.
NOTE: When removing rotary valve cover , pay
attention that the rotary valve stay in place, other-wise
it must be timed.
Remove carburetors from intake manifold.
Disconnect fuel bypass line between carburetors (twin
carburetors).
Remove carburetor(s) from rotary valve cover.
DISASSEMBLY AND INSPECTION
Using a suitable pump gauge tester, perform the fol-
lowing test proceeding as follows:
- Install pump gauge tester (P/N 295 000 083) on pulse
nipple.
- Pump tester until it reaches 28 kPa (4 PSI).
Diaphragm must stand pressure for 10 seconds. If
pressure drops, replace diaphragm.
TYPICAL PAGE
Sub-title with part
number(s) from exploded
view followed by part
name(s).
"TYPICAL" mention
indicates a general
view which does not
represent full detail.
Sub-sub-title in this
case indicates that
particular procedure
for XP is finished, so
from this point, all
others models are
concerned.
Title in italic indicates a
particular procedure
concerning a model.
Service tool to be
used to perform a
certain procedure.
Title indicates main
procedure to be
carried-out.
F01A0AS
Sub-sub-title in
capital indicates a
particular testing,
adjustment or
repair procedure.
Illustration
always follows
text it is
pertained to.
Numbers in a frame
are used to give a
sequence to be
perfomed.
Numbers are used
for description of
components.
Letters are used for
any measures.
F01F0XB
A
2
1
1 2
Bold numbers in the
text refer to the parts
shown in the exploded
view at the beginning
of the subsection.
INTRODUTION

IX
GENERAL INFORMATION
The use of RIGHT and LEFT indications in the text,
always refers to driving position (when sitting on
watercraft).
1. Left (port)
2. Right (starboard)
The information and component/system descrip-
tions contained in this manual are correct at time
of publication. Bombardier Inc. however, main-
tains a policy of continuous improvement of its
products without imposing upon itself any obliga-
tion to install them on products previously manu-
factured.
Bombardier Inc. reserves the right at any time to
discontinue or change specifications, designs,
features, models or equipment without incurring
obligation.
This
Shop Manual
uses technical terms which
may be different from the ones of the
Parts Cata-
logs
.
When ordering parts always refer to the specif-
ic model
Parts Catalogs
.
ILLUSTRATIONS AND
PROCEDURES
The illustrations show the typical construction of
the different assemblies and, in all cases, may not
reproduce the full detail or exact shape of the parts
shown, however, they represent parts which have
the same or a similar function.
As many of the procedures in this manual are in-
terrelated, we suggest, that before undertaking
any task, you read and thoroughly understand the
entire section or subsection in which the proce-
dure is contained.
A number of procedures throughout the book re-
quire the use of special tools. Before undertaking
any procedure, be sure that you have on hand all
the tools required, or approved equivalents.
Technical Publications
Bombardier Inc.
Valcourt (Quebec), Canada
F01L45B
12
-CAUTION
These watercraft are designed with parts di-
mensioned in both the metric and the impe-
rial systems. When replacing fasteners, make
sure to use only those recommended by Bom-
bardier.
INTRODUCTION

Section 01 SERVICE TOOLS AND PRODUCTS
Subsection 01 (MANDATORY SERVICE TOOLS)
01-01-1
MANDATORY SERVICE TOOLS 0
NOTE: The numbers outlined in black (example: ) are reference numbers to tools from other divi-
sions (Ski-Doo Snowmobiles and/or Sea-Doo Jet Boats). Matching reference numbers indicate the same
tool is being used on both products, even if the part numbers are different.
ENGINE
1
Degree wheel
P/N 295 000 007
A00B334
APPLICATION
717 and 787 engines.
Rubber pad
P/N 295 000 101
F01B0J4
APPLICATION
717 and 787 engines.
Rubber pad
P/N 290 877 032
F06B064
APPLICATION
947 engine.
1
3
6
0
3
5
0
3
4
0
3
3
0
3
2
0
3
1
0
3
0
0
2
9
0
2
8
0
2
7
0
2
6
0
2
5
0
2
4
0
2
3
0
2
2
0
2
1
0
2
0
0
1
9
0
1
8
0
1
7
0
1
6
0
1
5
0
1
4
0
1
3
0
1
2
0
1
1
0
1
0
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
1
0
2
0
3
0
4
0
5
0
6
0
7
0
8
0
9
0
1
0
0
1
1
0
1
2
0
1
3
0
1
4
0
1
5
0
1
6
0
1
7
0
1
8
0
1
9
0
2
0
0
2
1
0
2
2
0
2
3
0
2
4
0
2
5
0
2
6
0
2
7
0
2
8
0
2
9
0
3
0
0
3
1
0
3
2
0
3
3
0
3
4
0
3
5
0
3
6
0
547
NEW
Bearing pusher
P/N 290 876 500
A00B2J4
APPLICATION
717 engine.
Piston circlip installer
A) P/N 290 877 016
B) P/N 290 877 517
F06B014
APPLICATION
A) 717 and 787 engines.
B) 947 engine.
PTO flywheel
remover/installer
P/N 295 000 001
F01J0T4
APPLICATION
717 engine.
NOTE: This tool is also used for the
impeller.
12
548
553
Bearing pusher
P/N 290 876 501
F00B074
APPLICATION
787 engine.
Starter drive bearing pusher
P/N 290 876 502
F06B054
APPLICATION
947 engine.
Piston ring compressor (2)
P/N 290 876 965
F01B1T4
APPLICATION
947 engine.
NEW
NEW
NEW

Section 01 SERVICE TOOLS AND PRODUCTS
Subsection 01 (MANDATORY SERVICE TOOLS)
01-01-2
F01D884
1) Puller
P/N 290 876 298
2) Protective cap
(both ends)
P/N 290 876 557
3) Ring (both ends)
P/N 290 977 490
4) Ring halves (PTO)
P/N 290 977 475 (2)
5) Distance ring (MAG)
P/N 290 876 569
6) Ring halves (MAG)
P/N 290 276 025 (2)
7) Screw M8 x 40
P/N 290 840 681 (2)
8) Screw M8 x 70
P/N 290 841 201 (2)
APPLICATION
717 and 787 engines.
MAG side PTO side
8
1
5
2
3
4
4
6
877
200
554
555
556
557
558
559
560
Piston pin puller
P/N 529 035 503
F00B0T4
APPLICATION
All engines.
Sleeve set
A) P/N 529 035 542
(20 mm sleeve)
B) P/N 529 035 543
(21 mm sleeve)
F00B0U4
APPLICATION
A) 717 and 787 engines.
B) 947 engine.
Puller
P/N 290 876 488
F01B0I4
APPLICATION
717 and 787 engines.
Replacement parts:
1) P/N 290 240 860.
2) P/N 290 242 210.
NEW
NEW
562
21
Puller
P/N 295 000 106
A00C1A4
Puller plate
P/N 290 876 080
A00C1R4
Extension handle
P/N 295 000 125
F01D164
Screw M8 x 35 (3)
P/N 290 841 591
F00A094
Sleeve (3)
P/N 290 847 220
F00A0A4
APPLICATION
717 engine.
Pusher
P/N 290 876 605
A00C0Y4
APPLICATION
717 engine.
5
549
550
551
552
229

Section 01 SERVICE TOOLS AND PRODUCTS
Subsection 01 (MANDATORY SERVICE TOOLS)
01-01-3
Alignment support plate kit
P/N 529 035 506
1) Alignment plates
A) P/N 529 035 507
B) P/N 529 035 508
2) Support
P/N 529 035 511
3) Screw (2)
P/N 222 082 565
Lock washer (2)
P/N 213 000 001
Flat washer (2)
P/N 217 081 410
F00B0F4
APPLICATION
All models.
A) 139.5 mm jet pump.
B) 155.6 mm jet pump.
Alignment shaft
P/N 295 000 141
F00B0G4
APPLICATION
All models.
Adapter
P/N 295 000 157
F00B054
APPLICATION
XP Limited.
NEW
MPEM programmer
P/N 529 035 502
A01B5B4
APPLICATION
All models.
Digital multimeter
P/N 529 022 000
F01B1O4
APPLICATION
All models.
Flywheel extractor
P/N 295 000 156
F00B044
APPLICATION
SPX and XP Limited.
567
242
777
Engine leak tester kit
P/N 295 500 352
F01B2Q5
APPLICATION
717 and 787 engines.
Ring gear puller tool
P/N 420 976 235
F01B294
APPLICATION
787 engine.
Ring gear blocking tool
P/N 295 000 155
F01B264
APPLICATION
787 engine.
778
569
568

Section 01 SERVICE TOOLS AND PRODUCTS
Subsection 01 (MANDATORY SERVICE TOOLS)
01-01-4
Puller plate
P/N 529 035 533
F00B0S4
APPLICATION
947 engine.
Polygonal key
P/N 529 035 505
F00B0Y4
APPLICATION
Exhaust system of the 947 engine.
NEW
NEW

Section 01 SERVICE TOOLS AND PRODUCTS
Subsection 01 (MANDATORY SERVICE TOOLS)
01-01-5
COOLING/FUEL/OIL SYSTEMS
Hose pincher
P/N 295 000 076
A01B2I4
APPLICATION
All models.
Gear holder
P/N 290 277 905
A00C164
APPLICATION
717 engine.
Pliers
P/N 295 000 070
Oetiker 1099
F01D174
APPLICATION
All models.
2
235
601
Pliers
P/N 295 000 054
Caillau
F01B1T4
APPLICATION
All models.
NOTE: This tool is also used for
the propulsion system.
Coupler hose
P/N 295 500 258
41 cm (16 in)
F01E0Z4
APPLICATION
SPX and GTS models.
606
752

Section 01 SERVICE TOOLS AND PRODUCTS
Subsection 01 (MANDATORY SERVICE TOOLS)
01-01-6
PROPULSION SYSTEM
Impeller remover/installer
P/N 295 000 001
F01J0T4
APPLICATION
All models.
NOTE: This tool is also used for
the PTO flywheel (on some mod-
els).
Pliers
P/N 295 000 069
Oetiker 1090
F01D184
APPLICATION
All models.
Impeller shaft holder
P/N 295 000 082
F01B0W4
APPLICATION
All models.
553
602
603
Bearing/seal installer
P/N 295 000 107
F01J4K4
APPLICATION
All models.
Impeller shaft guide
P/N 295 000 002
F01J1O4
APPLICATION
All models.
Pliers
P/N 295 000 054
Caillau
F01B1T4
APPLICATION
All models.
NOTE: This tool is also used for
the fuel system.
604
605
606
VTS tool
P/N 295 000 133
F01B2P4
APPLICATION
SPX, GSX Limited and XP Limited.
607

Section 01 SERVICE TOOLS AND PRODUCTS
Subsection 02 (OPTIONAL SERVICE TOOLS)
01-02-1
OPTIONAL SERVICE TOOLS 0
NOTE: The numbers outlined in black (example: ) are reference numbers to tools from other divi-
sions (Ski-Doo Snowmobiles and/or Sea-Doo Jet Boats). Matching reference numbers indicate the same
tool is being used on both products, even if the part numbers are different.
ENGINE
1
Ring compressor
P/N 290 876 979
A01B1T4
APPLICATION
717 and 787 engines (82 mm).
Coil centering tool
P/N 290 876 922
A01B1V4
APPLICATION
717 engine.
Cylinder aligning tool
P/N 290 876 904
A00B084
APPLICATION
717 engine.
Handle
P/N 290 877 650
A00C3V4
APPLICATION
Use with pushers (P/N 290 876 609
and 290 877 740).
751
209
220
758
Rotary valve shaft pusher
P/N 290 876 609
F01B2B4
APPLICATION
787 engine.
Oil seal pusher
P/N 290 877 740
F01B2C4
APPLICATION
787 engine.
Ring halves (2)
P/N 290 876 330
Ring
P/N 290 977 480
F01B2D4
APPLICATION
787 and 947 engines.
757
759
761
762
Distance gauge
A) P/N 529 034 800
B) P/N 529 034 900
C) P/N 290 876 627
D) P/N 290 876 622
F01B0H4
APPLICATION
A) 717 engine.
B) 787 engine.
C) 947 engine.
D) 947 engine.
Puller and bolt
P/N 529 035 548 (puller)
P/N 529 035 549 (bolt)
F01B294
APPLICATION
947 engine.
NOTE: Bolt can be used with man-
datory puller (P/N 420 976 235).
760
561
NEW

Section 01 SERVICE TOOLS AND PRODUCTS
Subsection 02 (OPTIONAL SERVICE TOOLS)
01-02-2
Stroboscopic timing light
P/N 529 031 900
A00B4F4
APPLICATION
All models.
A) Four-pin magneto harness
P/N 295 000 131
B) Six-pin magneto harness
P/N 295 000 136
F01B284
APPLICATION
A) 717 engine.
B) 787 and 947 engines.
Dial indicator (TDC gauge)
P/N 295 000 143
A00B4E4
APPLICATION
All models.
225
763
755
230
Digital/induction type
tachometer
P/N 295 000 100
F01B1G4
APPLICATION
All models.
Timing mark pointer
P/N 295 000 130
F01B2O4
APPLICATION
717 engine.
Timing mark pointer
P/N 295 000 135
F01H544
APPLICATION
787 and 947 engines.
237
774
754
Crimping tool
P/N 295 100 164
F00B0E4
APPLICATION
Contacts of AMP plug connectors.
All models except SPX and GTS.
Terminal remover
Not sold by Bombardier
Snap-on
TT 600-4
F01B1J4
APPLICATION
All models.
Safety lanyard switch tool
P/N 295 000 121
F01B244
APPLICATION
All models.
NEW
775

Section 01 SERVICE TOOLS AND PRODUCTS
Subsection 02 (OPTIONAL SERVICE TOOLS)
01-02-3
Slide hammer puller
Not sold by Bombardier
Snap-on:Handle CJ93-1
Hammer CJ125-6
Claws CJ93-4
F01J0Z4
APPLICATION
717 and 787 engines.
NOTE: This tool is also used to
pull out impeller shaft seal.
Protective mat
P/N 295 000 128
F02B0A4
APPLICATION
All models.
F06B075
1) Puller
P/N 420 877 635
2) Protective cap
P/N 290 877 414
3) Screw
P/N 290 940 755
APPLICATION
947 engine.
889
3
2
1
Crankshaft protector
P/N 420 876 552
F00B034
APPLICATION
For use with pullers.
Gear/bearing puller
P/N 290 877 665
F04B034
APPLICATION
787 engine.
Exhaust outlet tool
P/N 295 000 132
F01B2A4
APPLICATION
All models.
764
765
831
Engine lifting device
Not sold by Bombardier
Do it yourself
Refer to 04-03 then look for
REMOVAL AND INSTALLATION
F01D0A4
APPLICATION
717 engine.
Feeler gauge 45°
Not sold by Bombardier
F01B1K4
APPLICATION
717 and 787 engines.
Steering cable tool
P/N 295 000 145
F01B2P4
APPLICATION
All models except the SPX and
GTS.
Snap-on
FB 300 A
780