Boospa JOYONWAY PB560XB88 User manual

I. Function
1 Pump
1.1 When the control system is powered on, by pressing this key, the pump can be turned
on and off.
1.2 The pump will turn off automatically after running for 3 minutes.
1.3 When the pump starts, the circ pump will also start.
2 Blower
2.1 When the control system is powered on, by pressing this key, the blower can be
turned on and off.
2.2 The blower will turn off automatically after running for 3 minutes.
2.3 When the blower starts, the circ pump will also start.
3 Lamp
PB560XB88

3.1 When the control system is powered on, by pressing this key the lamp can be turned
on and off.
3.2 The lamp will turn off automatically 2 hours after turned on.
4 Water cycle timer
4.1 Before using this function, the clock must be set correctly to ensure the accuracy of
the timer
4.2 The system has water cycle time period for setting. Before using this function, please
set the time period according to your needs.
4.3 The water cycle function will be turned on when the system time is in the time period
set. The water cycle function will stay off when the system time is not in the time
period.
5 Ozone
5.1 When the pump and blower are started, the ozone will be turned off.
5.2 When the pump and blower are off, and heating cycle pump or water cycle timer is on,
the ozone will be started automatically. When the heating cycle pump and water cycle
timer are turned off, the ozone will be automatically turned off.
6 Heating
6.1 When the system is powered on and the water temperature is lower than the set
temperature, the heating function will be started; when the water temperature reaches
the set temperature, the heating function will be turned off.
6.2 When the heating function is started, the heating circ pump is started in advance, and
the heater works later; When the heating function is turned off, the circ pump will be
shut down later.
7 Freeze proof
When the water temperature is below 6
℃ （ 43 ℉ ） , heating function will be started. The
heating function will be turned off when the temperature reaches 1 ℃ （ 5 ℉ ） .

II. Setting
1 Temperature unit
1.1 When the control system is powered on press “ ” for 5 seconds to
change the temperature unit （ ℃ or ℉ ） .
2 Temperature setting
2.1 When the system is on and not in setting state ， press“ ”and
“ ”to adjust the temperature value setting.
3 Clock setting
Clock setting interface
3.1 When the system is powered on press “ ” till the hour value of the
clock flashes in the LCD. Then press “ ”and“ ” to
adjust the hour value.

3.2 When the control system is powered on press “ ” till the minut value
flashes in the LCD. Press “ ” and “ ” to adjust the
minute value.
4 Set the heating time period timer
Start time setting interface of water cycle
time period
end time setting interface of water cycle
time period
LCD displays“ ” 、 “ ”indicating the start time and end time of time period.
4.1 When the control system is powered on, press“ ” until it enters
water cycle time range setting interface. The correspodent time value will flash. Press
“”and“ ”to adjust the time.
4.2 When water cycle time periods are set, the system will store them automatically.

III. Error code
Error code malfunction
description
handle method
E1 temperature sensor
malfunction
Please check the temperature sensor and its connection.
Replace a new one if necessary.
E2 temperature exceeds
the normal range
It indicates the control system sensing the temperature
sensor being overheated. When the heater is started, and
there is no water or very slim stream of water in side the
heater, this malfunction may happen. Please guarantee that
there is water inside the SPA tub. If this malfunction occurs
several times in a few days, please contact the service
provider or the manufacturer. Please pay attention to freeze
proof when the system senses that the temperature
sensor’s temperature is too low.
E4 Thermostat
disconnect
it indicates the heater is overheated. When the heating
started and there is no water or very slim water steam
inside the heater, this malfunction may happen. If this
malfunction occurs several times in a few days, please
contact the service provider or the manufacturer.
E5 Panel and control
box communication
malfunction
Please check the cable between control panel and the
control box. Replace a new one if necessary.