BOREA PastLS1 User manual

PastLS1 Qseven carrier
board for Rakun LS1
$HeadURL: https://svn.borea.si/svn/docs/rakun/rakun_pastls1/B01088/docs/ astLS1_DS.fodt $
$Rev: 1047 $ $Date: 2016-04-07 10:34:34 +0200 (čet, 07 apr 2016) $

Version 1.1
TABLE OF CONTENTS
1 GENERAL....................................................................................................... 7
1.1 About this document....................................................................................7
1.2 Revision history........................................................................................... 7
2 INTRODUCTION............................................................................................. 8
2.1 Device overview.......................................................................................... 8
2.2 Features...................................................................................................... 8
3 INSTALLATION GUIDE................................................................................. 10
4 ARCHITECTURE........................................................................................... 12
4.1 Block diagram........................................................................................... 12
4.2 USB connection........................................................................................ 12
4.3 UART connection...................................................................................... 13
5 JUMPERS......................................................................................................14
5.1 Boot select jumper 15............................................................................. 14
5.2 USB direction jumpers 8 and 11........................................................... 14
5.3 USB mode jumpers 12 and 13..............................................................15
5.4 UART to USB selection jumpers 16 and 17.......................................... 15
6 LED INDICATORS......................................................................................... 16
7 CONNECTOR DETAILS................................................................................ 17
7.1 Qseven connector 7................................................................................ 18
7.2 ower supply connector SW1................................................................... 21
7.3 Ethernet connector CON1......................................................................... 21
7.4 Micro SD card connector J1...................................................................... 22
7.5 I2C connector 3...................................................................................... 22
7.6 SATA connector J6.................................................................................... 23
7.7 SATA power connector 18....................................................................... 23
7.8 HDMI connector 1................................................................................... 24
7.9 USB 3.0 HOST connector J4.....................................................................25
7.10 USB OTG connector J5...........................................................................25
7.11 Mini CI-e connector 2..........................................................................26
7.12 Quicc Engine connector 10................................................................... 27
astLS1 Qseven carrier board for Rakun LS1

Version 1.1
7.13 G IO1/EC3 connector 9....................................................................... 28
7.14 G IO2/EC2 connector 14..................................................................... 29
7.15 MikroBUS connector 4+ 5....................................................................30
7.16 UART connector 6.................................................................................30
7.17 Debug console connector J7................................................................... 31
7.18 AUX SerDes connectors J8, J2, J3.........................................................31
8 APPENDIX A: PHY OARD ADD-ON OARD..............................................33
8.1 Architecture............................................................................................... 33
8.2 Jumpers.................................................................................................... 34
8.2.1 Ethernet Mode jumper 1.....................................................................34
8.2.2 Address jumper 2............................................................................... 34
8.3 LED indicators........................................................................................... 34
8.4 Connector details...................................................................................... 35
8.4.1 EC connector 4.................................................................................. 35
8.4.2 Ethernet connector 5.......................................................................... 35
9 APPENDIX : MIKRO US SLOT................................................................. 36
astLS1 Qseven carrier board for Rakun LS1

Version 1.1
ILLUSTRATION INDEX
Illustration 2.1: astLS1........................................................................................ 8
Illustration 3.1: Installation...................................................................................10
Illustration 4.1: Block diagram............................................................................. 12
Illustration 4.2: USB connection.......................................................................... 13
Illustration 4.3: UART connection........................................................................ 13
Illustration 5.1: osition of jumpers..................................................................... 14
Illustration 6.1: LED indicator.............................................................................. 16
Illustration 7.1: osition of connectors.................................................................17
Illustration 7.2: osition of connectors.................................................................17
Illustration 8.1: HYBoard add-on....................................................................... 33
Illustration 8.2: Block diagram of HYBoard....................................................... 33
astLS1 Qseven carrier board for Rakun LS1

Version 1.1
INDEX OF TABLES
Table 1.1: Revision history.................................................................................... 7
Table 3.1: Default jumper positions..................................................................... 10
Table 5.1: Boot select jumper 15.......................................................................14
Table 5.2: USB direction jumpers 8 and 11.....................................................15
Table 5.3: USB mode jumpers 12 and 13....................................................... 15
Table 5.4: UART to USB selection jumpers 16 and 17...................................15
Table 6.1: LED indicators.................................................................................... 16
Table 7.1: Qseven edge connector type.............................................................. 18
Table 7.2: Qseven edge connector pinout........................................................... 20
Table 7.3: ower supply connector type..............................................................21
Table 7.4: ower supply connector pinout...........................................................21
Table 7.5: Ethernet connector type......................................................................21
Table 7.6: Ethernet connector pinout...................................................................21
Table 7.7: Ethernet LEDs.................................................................................... 21
Table 7.8: Micro SD card connector type............................................................22
Table 7.9: Micro SD card connector pinout..........................................................22
Table 7.10: I2C connector type........................................................................... 22
Table 7.11: I2C connector pinout......................................................................... 22
Table 7.12: SATA connector type........................................................................ 23
Table 7.13: SATA connector pinout..................................................................... 23
Table 7.14: SATA power connector type..............................................................23
Table 7.15: SATA power connector pinout........................................................... 23
Table 7.16: HDMI connector type........................................................................ 24
Table 7.17: HDMI connector pinout..................................................................... 24
Table 7.18: USB 3.0 connector type.................................................................... 25
Table 7.19: USB 3.0 connector pinout................................................................. 25
Table 7.20: USB OTG connector type................................................................. 25
Table 7.21: USB OTG connector pinout.............................................................. 25
Table 7.22: Mini CIe connector type..................................................................26
Table 7.23: Mini CIe connector pinuot...............................................................26
Table 7.24: QUICC Engine connector type..........................................................27
Table 7.25: QUICC Engine connector pinout.......................................................27
Table 7.26: G IO1/EC3 connector type.............................................................. 28
Table 7.27: G IO1/EC3 connector pinout........................................................... 28
Table 7.28: G IO2/EC2 connector type.............................................................. 29
Table 7.29: G IO2/EC2 connector pinout........................................................... 29
Table 7.30: Microbus connector type...................................................................30
Table 7.31: Microbus connector pinout................................................................30
Table 7.32: UART connector type....................................................................... 30
Table 7.33: UART connector pinout.................................................................... 30
Table 7.34: Debug console connector type......................................................... 31
Table 7.35: Debug console connector pinout...................................................... 31
Table 7.36: AUX SerDes connector type............................................................. 31
Table 7.37: AUX SerDes 1 connector pinout....................................................... 31
Table 7.38: AUX SerDes 2 connector pinout....................................................... 32
Table 7.39: AUX SerDes 3 connector pinout....................................................... 32
Table 8.1: Ethernet mode selection jumper 1.................................................... 34
Table 8.2: UART to USB selection jumpers 16 and 17...................................34
Table 8.3: Ethernet LEDs.................................................................................... 34
Table 8.4: EC connector type.............................................................................. 35
astLS1 Qseven carrier board for Rakun LS1

Version 1.1
Table 8.5: EC connector extended pinout...........................................................35
Table 8.6: Ethernet connector type......................................................................35
Table 8.7: Ethernet connector pinout...................................................................35
Table 9.1: Currently available Click boards from Mikroelektronika......................36
astLS1 Qseven carrier board for Rakun LS1

Version 1.1
1 GENERAL
1.1 ABOUT THIS DOCUMENT
This document defines the hardware architecture of the RakunLS1 Qseven module.
1.2 REVISION HISTORY
Revision Date Notes
1.0 8. June 2015 Initial version
1.1 20. August 2015 Major rewrite, pinouts added
Table 1.1: Revision history
astLS1 Qseven carrier board for Rakun LS1

Version 1.1
2 INTRODUCTION
2.1 DEVICE OVERVIEW
astLS1 is Qseven carrier board that in addition to standard Qseven features supports additional interfaces
provided by Borea RakunLS1 Qseven module.
RakunLS1 module can be strictly Qseven compliant or can be configured to expose Freescale QorIQ
specific interfaces. In such RakunLS1 module configurations modified carrier board must be used to fully
utilize module interfaces.
Illustration 2.1: PastLS1
2.2 FEATURES
Qseven slot
Supports Qseven standard 2.0 + additional proprietary pins used for QorIQ specifics, present on a
RakunLS1 board.
Ethernet Interfaces
10/100/1000Mb/s Ethernet port, IEEE1588
•2x RGMII ports (multiplexed with G IOs and other interfaces) available on pin headers
•2x SGMII ports available on debug connectors
•Ethernet add-on board for RGMII ports available. Supports 1000BaseT and 1000BaseX
US Interfaces
Single USB port. Works as:
•USB 3.0 routed to USB 3.0 connector or
astLS1 Qseven carrier board for Rakun LS1

Version 1.1
•USB 2.0 routed to USB 3.0 connector or
•USB 2.0 routed to m CIe slot or
•USB OTG routed to USB OTG connector
SATA
SATA 3.0 with power connector 5V
HDMI Interface
HDMI 1.3
SD card
MicroSD slot. Rakun supports booting from SD
PCIe Interface
Mini CIe slot with CIe 0 lane from Qseven and USB
Normal, half and extended size supported
UARTs
Four 16450/16650 compatible UARTs with FIFOs. CMOS levels interfaces. Two of them can be routed to the
USB2UART converter.
Two additional QUICCEngine UART interfaces.
Debug console
USB to UART converter implemented on board for easier C connectivity
UART1 or UART2 from Qseven can be routed to the console
GPIO
Two G IO connectors with 26 G IO signals available
G IO1 interface is multiplexed with RGMII, CAN, USB2
G IO2 interface is multiplexed with RGMII, IEEE1588, WM
QUICCEngine
Two UCCs, supporting TDM, HDLC, Bisync, UART, Transparent …
QE interface is multiplexed with I2S, S/ DIF, G IO, HDMI.
Mikro US
MikroBus module slot for extension purposes (S I, UART, I2C). Allows connecting many of the shelf
extension boards.
Aux SerDes
Remaining three SerDes lanes from Qseven (Lane 0 is used for CIe) are available on auxiliary testing
connectors. SATA type connectors. Available interfaces:
•Up to 3x CIe
•Additional SATA
•2x SGMII
Power Supply
5V DC, 2A Input
Onboard regulators for 1.5V and 3.3V.
Typical power consumption depends on application. ower consumption without USB, Qseven board and
mini CIe board: 8mA.
Physical
hysical Dimensions: 143 × 92 mm.
Environment
Storage: -65ºC to +150ºC
Operation: -40ºC to +85ºC
Humidity: 5% to 90% Non-Condensing
Electrostatic Discharge Tolerance: 2KV
b free, ROHS compliant
astLS1 Qseven carrier board for Rakun LS1

Version 1.1
3 INSTALLATION GUIDE
Before start, perform the steps described below. Check figure 7.1 for the position of connectors and figure
5.1 for the position of jumpers.
1. Attach RakunLS1 and (optionally) HYBoard add-on as shown in figure below:
Illustration 3.1: Installation
2. Check presence of the following jumpers:
Jumper Setting Function
13 1 – 2 USB is connected to USB connectors
12 1 – 2 USB is connected to USB connectors
11 1 – 2 USB is connected to USB3.0 connector
8 1 – 2 USB is connected to USB3.0 connector
15 1 – 2 SD Boot
16 2 – 3 Console is UART2
17 2 – 3 Console is UART2
Table 3.1: Default jumper positions
3. Install uSD card with boot image to uSD slot.
4. Attach C to Console connector with USB cable. Start terminal application on C. Set it to 115200 kb/s, 8
bit, no parity, one stop bit (115200 8N1).
5. Optionally attach Ethernet, HDMI, USB.
astLS1 Qseven carrier board for Rakun LS1

Version 1.1
6. Connect external 5V power supply to DC power jack.
7. RakunLS1 will boot from SD card. There will be u-boot prompt in the terminal.
astLS1 Qseven carrier board for Rakun LS1

Version 1.1
4 ARCHITECTURE
4.1 BLOCK DIAGRAM
Block diagram of the device is shown in figure below:
Illustration .1: Block diagram
Design of the astLS1 is very straightforward and requires little explanation. inouts of the interfaces'
connectors are provided in chapter 4. Everything apart from USB and UART is connected straightforward
between Qseven module and I/O connectors. USB and UART have more options.
Qseven module RakunLS1 has multiplexed I/O pins. This means several interfaces are available on the
same pins. Consequently, several interfaces are available on G IO1/EC3, G IO2/EC2 and QE connectors.
For details, see chapter 6.
4.2 USB CONNECTION
USB connection is shown in figure below.
astLS1 Qseven carrier board for Rakun LS1
GPIO 1
GPIO, RGMII, MDIO,
I2C, WM, CAN, USB2
Extension connector
GPIO 2
G IO, RGMII, MDIO,
I2C, WM, IEEE1588
Extension Connector
Mikro us
S I, I2C, UART4
Extension Connector
QuiccEngine
Extension connector
US
FT230X
FTDI
US ctrl
LM3525M
TI
LAN
RJ45
Socket
EthMag
H5004NL
ulse
GPIO LEDs
SerDes3
AUX
SATA Connector
SerDes 2
AUX
SATA Connector
Qseven
C U Module
HDMI
SATA0
CIE0
UCC1
UCC3
UART4
SDHC
S I
I2C1
EC2
G IO
USB-
CTRL
ETH (EC3)
MII-M
USB1
Mini-PCIe
Slot 0
[ CIe 1x + USB]
MicroSD
Card
Socket
US _K
Socket
Mini A
US 1 2.0 OTG
Socket
Type A
SATA
Connector
US 1 3.0
Socket
Mini A
HDMI
Socket
SerDes 1
AUX
SATA Connector
UART
UART1, UART2,
UART3, UART4
Extension connector
EC3
G IO
UART3
UART2
UART1
CIE1-3
Power:
+5V 2A Input
+3.3V/2A
T S562209
+1.5V/0.8A LM1117
Power
Socket
ESD
ESD
ESD
ESD
Selection
jumpers
Selection
jumpers

Version 1.1
Illustration .2: USB connection
USB interface from the Qseven module can be linked to three separate interfaces: USB3.0 connector, USB
OTG connector and mini CIe slot. Switching is done via jumpers.
4.3 UART CONNECTION
UART connection is shown in figure below:
Illustration .3: UART connection
All UART signals are accessible on UART extension connector 6. UARTs can be used either as 4
independent null-modem UARTs (RX-TX only; UART1-4) or 2 independent UARTs with handshake signals
(RX, TX, RTS, CTS; UART1-2). UART 1 or UART2 can be routed to FTDI UART-USB converter for easier
console access.
astLS1 Qseven carrier board for Rakun LS1
US ctrl
LM3525M
TI
Qseven
C U Module
USB- OWERFAULT
USB1
Mini-PCIe
Slot
US 1 2.0 OTG
J5
US 1 3.0
J4
USB-DRVBUS
Jumpers
8/ 11
Jumpers
12/ 13
Mikro us
Slot
US
FT230X
FTDI
Qseven
C U Module
UART4
US _K
Socket
Mini A
UART3
UART2
UART1
UART
P6
Jumpers
16/ 17

Version 1.1
5 JUM ERS
osition of jumpers on the board is shown in figure below:
Illustration 5.1: Position of jumpers
5.1 BOOT SELECT JUM ER 15
Jumper 15 selects the boot source.
Jumper 15 is 2-pin jumper.
P15
Setting Function
1 – 2 ON Boot source is SD card (Default jumper placement)
1 – 2 OFF Boot source is QS I NOR flash
Table 5.1: Boot select jumper P15
5.2 USB DIRECTION JUM ERS 8 AND 11
Jumpers 8 and 11 select direction for the USB bus. It can be connected to the USB connectors or to the
CIe slot. Jumpers 8 and 11 must always be set up in the same way.
Jumpers 8 and 11 are 3-pin jumpers.
astLS1 Qseven carrier board for Rakun LS1
P17
P16
P15 P8
P11
P12
P13

Version 1.1
P8 and P11
Setting Function
1 – 2 Qseven board’s USB interface is connected to the USB connector (Default jumpers
placement)
2 – 3 Qseven board’s USB interface is connected to the CIe slot
Table 5.2: USB direction jumpers P8 and P11
5.3 USB MODE JUM ERS 12 AND 13
Jumpers 12 and 13 select mode of operation, when USB bus is connected to the USB connectors. USB
mode of operation can be USB3.0 or USB2.0 OTG. These two modes are available on separate USB
connectors J4 and J5 respectably. Jumpers 12 and 13 must always be set up in the same way.
Jumpers 12 and 13 are 3-pin jumpers.
This setting has no meaning when USB bus is connected to the CIe slot.
P12 and P13
Setting Function
1 – 2 USB bus is in USB3.0 mode, connected to the J4 connector (Default jumpers
placement)
2 – 3 USB bus is in USB2.0 OTG mode, connected to the J5 connector
Table 5.3: USB mode jumpers P12 and P13
5.4 UART TO USB SELECTION JUM ERS 16 AND 17
Jumpers 16 and 17 select the UART interface that is connected to the UART to USB converter FT230.
This device provides serial console on USB connector J7 for easy connection to the C. Jumpers 16 and
17 must always be set up in the same way.
Jumpers 16 and 17 are 3-pin jumpers.
P16 and P17
Setting Function
1 – 2 UART1 is used for serial console
2 – 3 UART2 is used for serial console (Default jumpers placement)
Table 5. : UART to USB selection jumpers P16 and P17
astLS1 Qseven carrier board for Rakun LS1

Version 1.1
6 LED INDICATORS
Board comprises three LED indicators.
Illustration 6.1: LED indicator
They are connected to the G IO pins.
LED Signal Note
LED1 G IO3_17 Active high
LED2 G IO3_18 Active high
LED3 G IO3_19 Active high
Table 6.1: LED indicators
astLS1 Qseven carrier board for Rakun LS1
LED1
LED2
LED3

Version 1.1
7 CONNECTOR DETAILS
Connectors present on the board are shown in figures below:
Illustration 7.1: Position of connectors
Illustration 7.2: Position of connectors
astLS1 Qseven carrier board for Rakun LS1
GPIO1/EC3
GPIO2/EC2
QE
Qseven
Ethernet
mikroBUS P4
mikroBUS P5
USB3.0
USB OTG
HDMI
uSD slot
Console
Power
mini PCIe
SATA
SATA Power
UART
I2C

Version 1.1
7.1 QSEVEN CONNECTOR 7
Supports Qseven standard 2.0 and additional proprietary pins used for QorIQ specifics.
Connector Type AS0B326-S78N-7F
Connector Manufacturer Foxconn
Table 7.1: Qseven edge connector type
Pin Signal Direction Pin Signal Direction
1 GND - 2 GND -
3 ETH_MDI3- Bidir 4 ETH_MDI2- Bidir
5 ETH_MDI3+ Bidir 6 ETH_MDI2+ Bidir
7 LINK100# In 8 LINK1000# In
9 ETH_MDI1- Bidir 10 ETH_MDI0- Bidir
11 ETH_MDI1+ Bidir 12 ETH_MDI0+ Bidir
13 NC - 14 ACT# In
15 NC - 16 NC -
17 NC - 18 SUS_S3# In
19 NC - 20 WRBTN# Out
21 SL _BTN# Out 22 NC -
23 GND - 24 GND -
25 GND - 26 WGIN Out
27 NC - 28 RSTBTN# Out
29 SATA_TX+ In 30 NC -
31 SATA_TX- In 32 NC -
33 NC - 34 GND -
35 SATA_RX+ Out 36 NC -
37 SATA_RX- Out 38 NC -
39 GND - 40 GND -
41 NC - 42 SD_CLK In
43 SD_CD# Out 44 NC -
45 SD_CMD In 46 SD_W Out
47 NC - 48 SD_DATA1 Bidir
49 SD_DATA0 Bidir 50 SD_DATA3 Bidir
51 SD_DATA2 Bidir 52 SD_DATA5 Bidir
53 SD_DATA4 Bidir 54 SD_DATA7 Bidir
55 SD_DATA6 Bidir 56 USB1_DRVBUS In
57 GND - 58 GND -
59 UCC1_RTSB_TXEN In 60 I2C1_SCL Bidir
61 NC - 62 I2C1_SDA Bidir
63 UCC1_CTSB_RXDV Out 64 SMB_ALERT# Out
65 UCC1_RXD Out 66 I2C2_SCL Bidir
67 UCC1_TXD In 68 I2C2_SDA Bidir
astLS1 Qseven carrier board for Rakun LS1

Version 1.1
Pin Signal Direction Pin Signal Direction
69 NC - 70 WDTRIG# Out
71 NC - 72 WDOUT In
73 GND - 74 GND -
75 NC - 76 NC -
77 NC - 78 NC -
79 NC - 80 NC -
81 USB1_TX- In 82 USB1_RX- Out
83 USB1_TX+ In 84 USB1_RX+ Out
85 NC - 86 USB1_ WRFAULT Out
87 NC - 88 NC -
89 NC - 90 NC -
91 USB1_VBUS Out 92 USB1_ID Bidir
93 USB1_D- Bidir 94 NC -
95 USB1_D+ Bidir 96 NC -
97 GND - 98 GND -
99 EC3_GTX_CLK125 Out 100 EC3_RXD0 Out
101 EC3_RX_DV Out 102 EC3_RXD1 Out
103 EC3_TX_EN In 104 EC3_RXD2 Out
105 EC3_GTX_CLK In 106 EC3_RXD3 Out
107 EC3_TXD0 In 108 EC3_RX_CLK Out
109 EC3_TXD1 In 110 EC2_RX_DV Out
111 EC3_TXD2 In 112 EC2_RXD0 Out
113 EC3_TXD3 In 114 EC2_RXD1 Out
115 EC2_TX_EN In 116 EC2_RXD3 Out
117 GND - 118 GND -
119 EC2_GTX_CLK In 120 NC -
121 EC2_GTX_CLK125 Out 122 NC -
123 EC2_TXD0 In 124 EC2_RX_CLK Out
125 EC2_TXD1 In 126 MDIO_OUT Bidir
127 EC2_TXD3 In 128 MDC_OUT In
129 EC2_TXD2 In 130 EC2_RXD2 Out
131 TMDS_CLK+ In 132 UART2_RTS# In
133 TMDS_CLK- In 134 UART2_CTS# Out
135 GND - 136 GND -
137 TMDS_L1+ In 138 NC -
139 TMDS_L1- In 140 NC -
141 GND - 142 GND -
143 TMDS_L0+ In 144 UART2_SOUT In
145 TMDS_L0- In 146 UART2_SIN Out
147 GND - 148 GND -
149 TMDS_L2+ In 150 HDMI_CTRL_DAT Out
astLS1 Qseven carrier board for Rakun LS1

Version 1.1
Pin Signal Direction Pin Signal Direction
151 TMDS_L2- In 152 HDMI_CTRL_CLK In
153 HDMI_H D# Out 154 NC -
155 CIE_CLK_REF+ In 156 NC -
157 CIE_CLK_REF- In 158 CIE_RST# In
159 GND - 160 GND -
161 CIE3_TX+ In 162 CIE3_RX+ Out
163 CIE3_TX- In 164 CIE3_RX- Out
165 GND - 166 GND -
167 CIE2_TX+ In 168 CIE2_RX+ Out
169 CIE2_TX- In 170 CIE2_RX- Out
171 UART1_SOUT In 172 UART1_RTS# In
173 CIE1_TX+ In 174 CIE1_RX+ Out
175 CIE1_TX- In 176 CIE1_RX- Out
177 UART1_SIN Out 178 UART1_CTS# Out
179 CIE0_TX+ In 180 CIE0_RX+ Out
181 CIE0_TX- In 182 CIE0_RX- Out
183 GND - 184 GND -
185 UCC1_CDB_RXER Out 186 UCC3_RTSB_TXEN In
187 UCC1_CLK09 Out 188 UCC3_CDB_RXER Out
189 UCC1_CLK10 Out 190 UCC3_CLK11 Out
191 NC - 192 UCC3_CLK12 Out
193 NC - 194 UCC3_CTSB_RXDV Out
195 UCC3_RXD Out 196 UCC3_TXD In
197 GND - 198 GND -
199 S I_MOSI In 200 S I_CS0# In
201 S I_MISO Out 202 S I_CS1# In
203 S I_CLK In 204 JTAG_TRST# Out
205 NC - 206 NC -
207 JTAG_TCK Out 208 JTAG_TDI Out
209 JTAG_TDO In 210 JTAG_TMS Out
211 VCC - 212 VCC -
213 VCC - 214 VCC -
215 VCC - 216 VCC -
217 VCC - 218 VCC -
219 VCC - 220 VCC -
221 VCC - 222 VCC -
223 VCC - 224 VCC -
225 VCC - 226 VCC -
227 VCC - 228 VCC -
229 VCC - 230 VCC -
Table 7.2: Qseven edge connector pinout
astLS1 Qseven carrier board for Rakun LS1