
Installation and connection en
9
5Installation and connection
Instal l ati on and c onnect i on
Do not install the appliance behind a decorative door 
or the door of a kitchen unit, as this may cause the 
appliance to overheat.
Gas connection
Installation must only be performed by an approved 
expert or a licensed after-sales service engineer in 
accordance with the instructions specified under "Gas 
connection and conversion to a different gas type".
For the licensed expert or after-sales service
Caution!
■The setting conditions for this appliance are 
specified on the rating plate on the back of the 
appliance. The gas type set in the factory is marked 
with an asterisk (*).
■Before setting up the appliance, check the grid 
access conditions (gas type and gas pressure) and 
ensure that the gas setting of the appliance meets 
these conditions. If the appliance settings have to be 
changed, follow the instructions in the section "Gas 
connection and conversion to a different gas type".
■This appliance is not connected to a waste gas 
main. It must be connected and commissioned in 
accordance with the installation conditions. Do not 
connect the appliance to a waste gas main. All 
ventilation regulations must be observed.
■The gas connection must be made via a fixed, i.e. 
not mobile connection (gas line) or via a safety 
hose. 
■If using the safety hose, ensure that the hose is not 
trapped or crushed. The hose must not come into 
contact with hot surfaces.
■* The gas line (gas pipe or gas safety hose) can be 
connected to the right- or left-hand side of the 
appliance. The connection must have an easily 
accessible shut-off device.
* Optional. Available for some appliances.
Target appliance operating pressure
Your appliance's target operating pressure is specified 
on the rating plate on the back of the appliance.
All the data on your appliance's rating plate relates to 
these pressure values. The manufacturer shall not be 
held liable for results, performance or any risk caused 
by operating the appliance at pressure values other 
than those specified. 
:Warning – Safety information! 
If the gas pressure in your distributing pipes is higher 
(20%) than the values specified on the appliance's 
rating plate, it is important that you operate the 
appliance with a suitable gas regulator for your safety. 
If you do not know what the gas pressure in your 
distributing pipes is, contact your local gas company.
The gas regulator must be connected, maintained and 
adjusted by specialists from your local gas company.
Faults in the gas installation/smell of gas
If you notice a smell of gas or faults in the gas 
installation, you must
■immediately shut off the gas supply and/or close the 
gas cylinder valve
■immediately extinguish all naked flames and 
cigarettes
■switch off electrical appliances and lights
■open windows and ventilate the room
■call the aftersales service or the gas supplier
Moving the appliance by the gas line or door handle
Do not move the appliance while holding the gas line; 
the gas pipe could be damaged. There is a risk of a gas 
leak! Do not move the appliance while holding it by the 
door handle. The door hinges and door handle could 
be damaged.
Electrical connection
The appliance is designed to operate at 220-240 V. A 
16 A fuse is required for connection. 
Have the appliance installed by your after-sales service. 
Any damage arising from the appliance being 
connected incorrectly will invalidate the warranty.
Caution!
■If the electricity supply drops below 180 V, the 
electrical ignition system does not work.
■If the supply cord is damaged, it must be replaced 
by the manufacturer, its service agent or similarly 
qualified persons in order to avoid a hazard.
:Warning – Danger of death! 
There is a risk of electric shock if you touch live 
components.
■Always make sure your hands are dry when you 
touch or hold the mains plug.
■Only pull out the mains cable by taking hold of the 
plug and removing the plug; never pull it out by the 
mains cable itself, as this could damage it.
■Never unplug the mains plug when the appliance is 
in operation.
Please note the following information and ensure that:
Notes
■The mains plug fits the socket.
■The cable cross section is adequate.
■The earthing system is properly installed.
■The mains cable is only replaced by a qualified 
electrician (if this is necessary).Spare mains cables 
can be ordered from our after-sales service.
■No power strips/multi-way connectors or extension 
cables are used.
■If using a residual current device, only use one that 
bears the mark z.
The presence of this mark is the only way to be sure 
that it fulfils all the applicable regulations.
■The mains plug can be accessed at all times.
■The mains cable is not kinked, crushed, modified or 
severed.
■The mains cable does not come into contact with 
heat sources.