Bosch ASM 32 User manual

Robert Bosch GmbH
Power Tools Division
70745 Leinfelden-Echterdingen
Germany
www.bosch-garden.com
F 016 L70 798 (2011.04) O / 237 UNI
ASM
32 | 32 F
de Originalbetriebsanleitung
en Original instructions
fr Notice originale
es Manual original
pt Manual original
it Istruzioni originali
nl Oorspronkelijke
gebruiksaanwijzing
da Original brugsanvisning
sv Bruksanvisning i original
no Original driftsinstruks
fi Alkuperäiset ohjeet
el Πρωτότυπο οδηγιών χρήσης
tr Orijinal işletme talimat
pl Instrukcja oryginalna
cs Původní návod k používání
sk Pôvodný návod na použitie
hu Eredeti használati utasítás
ru Оригинальное руководст-
во по эксплуатации
uk Оригінальна інструкція з
експлуатації
ro Instrucţiuni originale
bg Оригинална инструкция
sr Originalno uputstvo za rad
sl Izvirna navodila
hr Originalne upute za rad
et Algupärane kasutusjuhend
lv Instrukcijas oriģinālvalodā
lt Originali instrukcija
OBJ_DOKU-24786-001.fm Page 1 Friday, April 15, 2011 9:22 AM

| 3
Bosch Power Tools F 016 L70 798 | (15.4.11)
ASM 32 F
Made in UK.
TYP 0 600 xxx xxx 57 9 230V ~ 50/60Hz XXXXW
xx.xx kg
IPX4
96
LBA
3
xxxx l/mlh
Robert Bosch GmbH.D-70745, Leinfelden
xxxxxxxxxxxx
20xx
STOP
7
7
6
10
9
8
2
3
1
5
4
5
4
OBJ_BUCH-1393-001.book Page 3 Friday, April 15, 2011 10:36 AM

F 016 L70 798 | (15.4.11) Bosch Power Tools
4|
CLICK!
2
CLICK!
CLICK!
1
2
2
CLICK!
3
2
2
5
5
4 14
products not sold in GB
9
1
6
11
1312
ASM 32 F
ASM 32
1
ASM 32
ASM 32 F
D
C2
C1
BA
OBJ_BUCH-1393-001.book Page 4 Friday, April 15, 2011 10:36 AM

| 5
Bosch Power Tools F 016 L70 798 | (15.4.11)
0
I
2
2
1
1
0
I
15
16
17
ASM 32 F
ASM 32
ASM 32
1
1
2
2
2
3
2
3
HG
FE
OBJ_BUCH-1393-001.book Page 5 Friday, April 15, 2011 10:36 AM

English | 15
Bosch Power Tools F 016 L70 798 | (15.4.11)
en
Safety Notes
Warning! Read these instructions carefully, be
familiar with the controls and the proper use
of the machine. Please keep the instructions
safe for later use!
Explanation of symbols
General hazard safety alert.
Read instruction manual.
Pay attention that bystanders are not
injured through foreign objects thrown
from the machine.
Keep bystanders a safe distance away
from the machine.
Switch off and remove plug from mains
before adjusting, cleaning or if the ca-
ble is entangled and before leaving the
garden product unattended for any pe-
riod. Keep the supply flexible cord
away from the cutting blades.
Sharp blade(s). Beware of severing
toes or fingers.
Wait until all machine components
have completely stopped before
touching them. The blades continue to
rotate after the machine is switched
off, a rotating blade can cause injury.
Do not use the machine in the rain or
leave it outdoors when it is raining.
Operation
fNever allow children or people unfamiliar
with these instructions to use the machine.
Local regulations may restrict the age of the
operator. When not in use store the machine
out of reach of children.
fThis tool is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of ex-
perience and knowledge, unless they have
been given supervision or instruction con-
cerning use of the appliance by a person re-
sponsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
fNever mow while people, especially children
or pets, are nearby.
fThe operator or user is responsible for acci-
dents or hazards occurring to other people
or their property.
fDo not operate the machine when barefoot
or wearing open sandals, always wear sub-
stantial footwear and long trousers.
fThoroughly inspect the area where the ma-
chine is to be used and remove all stones,
sticks, wires, bones and other foreign ob-
jects.
fBefore using, always visually inspect to see
that the blades, blade bolts and cutter as-
sembly are not worn or damaged. Replace
worn or damaged blades and bolts in sets to
preserve balance.
fOn multi-bladed lawnmowers, take care as
rotating one blade can cause other blades to
rotate.
fMow only in daylight or in good artificial light.
fAvoid operating the machine in wet grass,
where feasible.
fWalk, never run.
fWorking on banks can be dangerous.
– Do not mow excessively steep slopes.
– Always be sure of your footing on slopes
or wet grass.
– Mow across the face of slopes – never up
and down.
– Exercise extreme caution when changing
direction on slopes.
– Use extreme caution when stepping back
or pulling the machine towards you.
– Never mow by pulling the mower towards
you.
STOP
OBJ_BUCH-1393-001.book Page 15 Friday, April 15, 2011 10:36 AM

16 | English
F 016 L70 798 | (15.4.11) Bosch Power Tools
fStop the blades if the machine has to be tilt-
ed for transportation when crossing surfaces
other than grass and when transporting the
machine to and from the area to be mowed.
fDo not tilt the machine when starting or
switching on the motor, except if the ma-
chine has to be tilted for starting in long
grass. In this case, do not tilt it more than ab-
solutely necessary and tilt only the part
which is away from the operator. Always en-
sure that both hands are in the operating po-
sition before returning the machine to the
ground.
fSwitch on the motor according to the in-
structions with feet well away from rotating
parts.
fDo not put hands or feet near or under rotat-
ing parts.
fAlways stand clear of the discharge zone
when operating the machine.
fNever pick up or carry the machine while the
motor is running.
fNever operate the appliance with defective
guards or shields, or without safety devices,
for example deflectors and/or grass catchers
in place.
fBe careful during adjustment of the lawn-
mower to prevent entrapment of the feet and
hands between moving blades and fixed
parts of the lawnmower.
fKeep supply cables and extension cables
away from the blade. The blade can cause
damage to the cables and lead to contact
with live parts. Beware electric shock hazard.
Remove the plug from the socket:
– whenever you leave the machine,
– before clearing a blockage,
– before checking, cleaning or working on the
machine,
– after striking a foreign object. Inspect the
machine for damage and make repairs as
necessary,
– if the machine starts to vibrate abnormally
(check immediately).
Power supply
fThe voltage indicated on the rating plate
must correspond to the voltage of the power
source.
fWe recommend that this equipment is only
connected into a socket which is protected
by a circuit-breaker that would be actuated
by a 30 mA residual current.
fOnly use or replace power supply cables for
this unit which correspond to the types indi-
cated by the manufacturer. See the operat-
ing instructions for the order no. and types.
fNever touch the mains plug with wet hands.
fDo not run over, crush or pull the power sup-
ply cable or extension lead, otherwise it may
be damaged. Protect the cable from heat, oil
and sharp edges.
fThe extension lead must have a cross section
in accordance with the operating instruc-
tions and be protected against splashed wa-
ter. The connection must not be in water.
fAlways wear gardening gloves when handling
or working near the sharp blades.
Maintenance
fAlways wear gardening gloves when han-
dling or working near the sharp blades.
fKeep all nuts, bolts and screws tight to be
sure that the machine is in safe working con-
dition.
fCheck the grassbox/bag frequently for wear
or deterioration.
fExamine the machine and replace worn or
damaged parts for safety.
fEnsure replacement parts fitted are Bosch
approved.
Product Description and Speci-
fications
Read all safety warnings and all in-
structions. Failure to follow the warn-
ings and instructions may result in
electric shock, fire and/or serious inju-
ry.
OBJ_BUCH-1393-001.book Page 16 Friday, April 15, 2011 10:36 AM

English | 17
Bosch Power Tools F 016 L70 798 | (15.4.11)
Intended Use
The garden product is intended for domestic
lawn mowing.
Delivery Scope
Carefully remove the garden product from its
packaging and check if the following parts are
complete:
– Lawnmower with handle assembly
– Handle bottom
– 2 Bolts (fitted to handle bottom)
– 2 Wing nuts (fitted to handle bottom)
– 2 Pivot pins (fitted to handle bottom)
– 2 Pivot covers (fitted to handle bottom)
– 2 Grassbox parts (ASM 32)
– Grassbox (ASM 32 F)
– Operating instructions
When parts are missing or damaged, please con-
tact your dealer.
When fully assembled the garden product
weighs approximately 8.5–11.0 kg. If necessary,
obtain assistance to remove from packaging.
Take care when removing from packaging or car-
rying the garden product to the lawn, as the
blades are sharp.
Product Features
The numbering of the garden product features
refers to the illustration of the garden product
on the graphics page.
1Handle top
2Switch lever
3Safety button
4Power plug **
5Cable restraint*/ **
6Handle bottom
7Serial number
8Grassbox
9Height of cut lever
10 Ventilation slots
11 Handle stop
12 Pivot cover
13 Pivot pin
14 Extension cable*
15 Blade
16 Cutting cylinder
17 Adjuster screw
*Accessories shown or described are not part of the
standard delivery scope of the product. A complete
overview of accessories can be found in our acces-
sories program.
** country specific
Technical Data
Cylinder Mower ASM 32 ASM 32 F
Article number 3 600 H89 A.. 3 600 H89 B..
Rated power input W400340
Blade width cm 32 32
Height of cut mm 12 – 32 12 – 32
Grassbox, capacity l3123
Weight according to EPTA-Procedure 01/2003 kg 11.0 8.5
Protection class /II /II
Serial number See serial number 7(type plate) on the machine
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries,
these values can vary.
Please observe the article number on the type plate of your garden product. The trade names of the individual garden
products may vary.
OBJ_BUCH-1393-001.book Page 17 Friday, April 15, 2011 10:36 AM

18 | English
F 016 L70 798 | (15.4.11) Bosch Power Tools
Noise/Vibration Information
Measured sound values determined according
to EN 60335.
Typically the A-weighted noise levels of the
product are: Sound pressure level 79 dB(A);
sound power level 92 dB(A). Uncertainty
K=2dB.
Vibration total values ah(triax vector sum) and
uncertainty K determined according to
EN 60335:
ah<2.5 m/s2, K =1.5 m/s2.
Declaration of Conformity
We declare under our sole responsibility that
the product described under “Technical data” is
in conformity with the following standards or
standardization documents: EN 60335 accord-
ing to the provisions of the directives
2004/108/EC, 2006/42/EC, 2000/14/EC.
2000/14/EC: Guaranteed sound power level
96 dB(A). Conformity assessment procedure
according to Annex VI.
Equipment category: 32
Notified body:
SRL, Sudbury, England, Nr. 1088
Technical file at:
Bosch Lawn and Garden Ltd., PT-LG/EAE,
Stowmarket, Suffolk IP14 1EY, England
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
21.02.2011
Assembly
fWarning! Switch off, remove plug from
mains before adjusting, cleaning or if cable
is cut, damaged or entangled.
For Your Safety
fThe blades continue to rotate for a few sec-
onds after the machine is switched off.
fCaution – do not touch the rotating blades.
Electrical Safety
Your machine is double insulated for safety and
requires no earth connection. The operating
voltage is 230 V AC, 50 Hz (for non-EU countries
220 V, 240 V as applicable). Only use approved
extension cables. Contact your Bosch Service
Centre for details.
Extension cords/leads should only be used if
they comply with H05VV-F, H05RN-F types or
IEC type design (60227 IEC 53, 60245 IEC 57).
If you want to use an extension cable when op-
erating your product, only the following cable di-
mensions should be used:
–1.0mm
2: max. length 40 m
– 1.5 mm2: max. length 60 m
– 2.5 mm2: max. length 100 m
Note: If an extension cable is used it must be
earthed and connected through the plug to the
earth cable of your supply network in accord-
ance with prescribed safety regulations.
If in doubt contact a qualified electrician or the
nearest Bosch Service Centre.
fWARNING! Inadequate extension cables
can be dangerous. Extension cable, plug
and socket must be of watertight construc-
tion and intended for outdoor use.
Cable connections should be kept dry and off
the ground.
It is recommended for increased electrical safe-
ty to use a Residual Current Device (RCD) with
a tripping current of not more than 30 mA. Al-
ways check your RCD every time you use it.
For products not sold in GB:
WARNING: For your safety, it is required that
the plug attached to the machine is connected
with the extension cord. The coupling of the ex-
tension cord must be protected against splash
water, be made of rubber or coated with rubber.
The extension cord must be used with a cable
strain relief.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
OBJ_BUCH-1393-001.book Page 18 Friday, April 15, 2011 10:36 AM

English | 19
Bosch Power Tools F 016 L70 798 | (15.4.11)
The connection lead must be inspected for signs
of damage at regular intervals and may only be
used if in perfect condition.
If the supply cord is damaged, it must be re-
placed by a Bosch Service Centre.
Products sold in GB only: Your product is fitted
with a BS 1363/A approved electric plug with in-
ternal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets,
it should be cut off and an appropriate plug fit-
ted in its place by an authorised customer serv-
ice agent. The replacement plug should have the
same fuse rating as the original plug.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be in-
serted into a mains socket elsewhere.
Products sold in AUS and NZ only: Use a resid-
ual current device (RCD) with a rated residual
current of 30 mA or less.
Assembly
fEnsure the cables are not trapped when
folding/unfolding top/bottom handles. Do
not drop the handles.
Handle assembly (see figure A)
Fix the handle bottom 6to the body of the mow-
er using pivot pins 13.
Ensure that the pivot covers 12 are fitted to the
handle bottom 6.
fEnsure that the handle stop 11 is fitted to
the right hand side when operating the
mower (ASM 32).
Attach the handle top 1with the bolts and the
wing nuts to the handle bottom 6.
Note: Ensure that the cable clip supplied is used
to fix the cable to the handle.
Attach cable to cable restraint 5ensuring that
sufficient cable slack is available. (see figure B)
Remove transport packaging/label from the
mower, the blades will require adjustment – see
“Blade Maintenance (see figure G)”.
Snap together the grassbox and fitting/remov-
ing the grassbox (ASM 32) (see figure C1)
Snap together the grassbox and fitting/remov-
ing the grassbox (ASM 32 F) (see figure C2)
Snap together the grassbox.
Attach/remove the grassbox as shown.
Adjusting the Cutting Height (see figure D)
fStop, release switch lever and wait until the
motor stops before adjusting height. The
blades continue to rotate after the machine
is switched off, a rotating blade can cause in-
jury.
The lawnmower can be set to several cutting
heights.
For this purpose, press the height of cut lever 9
outward (n) then move up or down (o) to the
desired cutting height while supporting the
weight of the mover with the other hand.
For the first cutting of the season, a high cutting
height should be selected.
Operation
Starting
fThe blade continues to rotate for a few sec-
onds after the machine is switched off. Al-
low the motor/blade to stop rotating before
switching “on” again.
fDo not rapidly switch off and on.
Note: To aid starting push handle down to lift
front wheels.
Starting (see figure E)
nPress and hold the safety button 3.
oSqueeze the switch lever 2towards
the handle.
Release the safety button 3.
Stopping
Release the switch lever 2.
noSnap together both top and bottom half
of the grassbox.
pAttach/remove the grassbox as shown.
0
I
2
1
OBJ_BUCH-1393-001.book Page 19 Friday, April 15, 2011 10:36 AM

20 | English
F 016 L70 798 | (15.4.11) Bosch Power Tools
Mowing (see figure F)
Place the garden product on the edge of the
lawn, as close to the power point as possible.
Work away from the power point.
Position the cable to opposite side (already
done) at the end of each turn.
The blades may require adjustment, particularly
before first use – see “Blade Maintenance
(see figure G)”.
When mowing do not allow the motor to labour
particularly in heavy conditions.
When the motor labours the speed of the motor
drops and you will hear a change in the motor
sound, when this occurs stop mowing, release
the switch lever 2and raise the height of cut.
Failure to do so will could damage the machine.
Troubleshooting
The following chart lists problem symptoms, possible causes and corrective action, if your garden
product does not operate properly. If these do not identify and correct the problem, contact your
service agent.
fWarning: Switch off and remove plug from mains before investigating fault.
Problem Possible Cause Corrective Action
Garden product fails to operate Power turned off Turn power on
Mains socket faulty Use another socket
Extension cable damaged Inspect cable, replace if dam-
aged
Fuse faulty/blown Replace fuse
Garden product functions
intermittently
Extension cable damaged Inspect cable, replace if dam-
aged
Internal wiring of garden prod-
uct damaged
Contact Service Agent
Garden product labours or belt
squeals
Height of cut too low Increase height of cut (see “Ad-
justing the Cutting Height
(see figure D)”)
Blades off cut Adjust blades
Garden product leaves ragged
finish
Cutting blade blunt Contact Service Agent
Blades off cut Adjust blades
Cutting blade not rotating Cutting blade obstructed Switch off garden product
Clear obstruction (always wear
gardening gloves)
Belt is slipping or is damaged Contact Service Agent
Excessive vibrations/noise Cutting blade damaged Contact Service Agent
Cutting blades not adjusted
evenly
Adjust blades
Poor collection Mowing in wet conditions Allow grass to dry
OBJ_BUCH-1393-001.book Page 20 Friday, April 15, 2011 10:36 AM

English | 21
Bosch Power Tools F 016 L70 798 | (15.4.11)
Maintenance and Service
Maintenance and Cleaning
fStop, remove plug from the power supply
and remove the grassbox.
fAlways wear gardening gloves when han-
dling or working near the sharp blades.
Note: To ensure long and reliable service, carry
out the following maintenance regularly.
Regularly check for obvious defects such as
loose, dislodged or damaged blades, loose fix-
ings, and worn or damaged components.
Check that covers and guards are undamaged
and correctly fitted. Carry out necessary mainte-
nance or repairs before using.
If the garden product should happen to fail de-
spite the care taken in manufacture and testing,
repair should be carried out by an authorised
customer service agent for Bosch garden prod-
ucts.
In all correspondence and spare parts orders,
please always include the 10-digit article
number given on the type plate of the garden
product.
Blade Maintenance (see figure G)
fStop, remove plug from the power supply
and remove the grassbox.
fAlways wear gardening gloves when han-
dling or working near the sharp blades.
The cutting cylinder should be adjusted if the
grass is not cut cleanly and evenly.
Turn the garden product upside down.
Using a screwdriver turn both the adjuster
screws 17 clockwise a little at a time until the
cutting cylinder 16 lightly brushes the bottom
blade 15.
Note: The blades act like a pair of shears.
After Use/Storage
fStop, remove plug from the power supply
and remove the grassbox.
Clean the exterior of the machine thoroughly us-
ing a soft brush and cloth. Do not use water, sol-
vents or polishes. Remove all grass and debris,
especially from the ventilation slots 10.
Turn the machine on its side and clean the blade
area. If grass cuttings are compacted in the
blade area, remove with a wooden or plastic im-
plement.
fAlways wear gardening gloves when han-
dling or working near the sharp blades.
Store the machine in a secure, dry place out of
the reach of children. Do not place other objects
on top of the machine.
To aid storage fold the handles. (see figure H)
fEnsure the cables are not trapped when
folding/unfolding top/bottom handles. Do
not drop the handles.
After-sales Service and Customer As-
sistance
Our after-sales service responds to your ques-
tions concerning maintenance and repair of your
product as well as spare parts. Exploded views
and information on spare parts can also be
found under:
www.bosch-garden.com
Our customer service representatives can an-
swer your questions concerning possible appli-
cations and adjustment of products and acces-
sories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: [phone]
Fax: [phone]
E-Mail: [email protected]
OBJ_BUCH-1393-001.book Page 21 Friday, April 15, 2011 10:36 AM

22 | English
F 016 L70 798 | (15.4.11) Bosch Power Tools
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: [phone]
Fax: [phone]
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: [phone]
Fax: [phone]
Inside New Zealand:
Phone: [phone]
Fax: [phone]
Outside AU and NZ:
Phone: [phone]
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: [phone]
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: [phone]
Fax: [phone]
E-Mail: [email protected].za
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: [phone]
Fax: [phone]
E-Mail: [email protected]
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: [phone]
Fax: [phone]
E-Mail: [email protected]
Bosch Headquarters
Midrand, Gauteng
Tel.: [phone]
Fax: [phone]
E-Mail: [email protected]
Disposal
The garden product, accessories and packaging
should be sorted for environmental-friendly re-
cycling.
Do not dispose of garden products into house-
hold waste!
Only for EC countries:
According to the European direc-
tive 2002/96/EC for Waste Electri-
cal and Electronic Equipment and
its implementation into national
law, electrical and electronic
equipment that are no longer usa-
ble must be collected separately and disposed
of in an environmentally correct manner.
Subject to change without notice.
OBJ_BUCH-1393-001.book Page 22 Friday, April 15, 2011 10:36 AM