Bosch NDA-FMT200-DOME User manual

IP200 MiniDome In-Ceiling Mount
NDA-FMT200-DOME
en Installation Manual

IP200 MiniDome In-Ceiling Mount Table of Contents | en 3
Bosch Security Systems Installation Manual AM18-Q0626 | v1.0 | 2012.09
Table of Contents
1Safety 4
1.1 Safety precautions 4
2 Unpacking 5
2.1 Parts List 5
3 Installation Overview 6
4 Installing a Recessed Mount 7
4.1 Overview 7
4.2 Installing the Recessed Mount 7
4.3 Installing the Camera to the Recess Mount 11
5 Connection 14

4en | Safety IP200 MiniDome In-Ceiling Mount
AM18-Q0626 | v1.0 | 2012.09 Installation Manual Bosch Security Systems
1Safety
Before installing and operating the camera, please read this
manual carefully.
1.1 Safety precautions
This manual is the intellectual property of Bosch Security
Systems and is protected by copyright. All rights reserved.
Contact: www.boschsecurity.com
DANGER!
High risk: This symbol indicates an imminently hazardous
situation such as "Dangerous Voltage" inside the product.
If not avoided, this will result in an electrical shock, serious
bodily injury, or death.
WARNING!
Medium risk: Indicates a potentially hazardous situation.
If not avoided, this could result in minor or moderate bodily
injury.
CAUTION!
Low risk: Indicates a potentially hazardous situation.
If not avoided, this could result in property damage or risk of
damage to the unit.
NOTICE!
This symbol indicates information or a company policy that
relates directly or indirectly to the safety of personnel or
protection of property.

IP200 MiniDome In-Ceiling Mount Unpacking | en 5
Bosch Security Systems Installation Manual AM18-Q0626 | v1.0 | 2012.09
2 Unpacking
This equipment should be unpacked and handled with care. If
an item appears to have been damaged in shipment, notify the
shipper immediately.
Verify that all the parts listed in the applicable Parts List below
are included. If any items are missing, notify your Bosch
Security Systems Sales or Customer Service Representative.
The original packing carton is the safest container in which to
transport the unit and must be used if returning the unit for
service. Save it for possible future use.
2.1 Parts List
The following table lists the parts included in the In-ceiling
(recessed) mount (NDA-FMT200-DOME):
Quantity Part
1 In-ceiling mount: NDA-FMT200-DOME
1 White trim ring A (inner diameter: 102 mm)
with two M3 captive screws
1 White trim ring B (inner diameter: 98 mm) with
two M3 captive screws
4 Four M4 x 6 mm screws
4 Four M4 x 15 mm screws
1 Security Torx T-10 L wrench
1 Installation manual (this booklet)

6en | Installation Overview IP200 MiniDome In-Ceiling Mount
AM18-Q0626 | v1.0 | 2012.09 Installation Manual Bosch Security Systems
3 Installation Overview
The IP200 MiniDome camera comes with the hardware and
installation instructions necessary to mount the camera to a
concrete ceiling.
This following mounting accessory is available :
– In-ceiling mount, used in applications where the camera is
mounted into a recessed ceiling.
The mount is supplied with two different trim rings and
different tooling hole positions on the sides of the recess
mount. Use the table below to choose the ring and hole
position for your camera.
The installation should be made by qualified installation
personnel and conform to the National Electrical Code and
applicable local codes.
Trim ring Hole Camera
Ring A A NDN-265-PIO
Ring B B NDC-225-P
NDC-225-PI
NDC-255-P
NDC-265-P

IP200 MiniDome In-Ceiling Mount Installing a Recessed Mount | en 7
Bosch Security Systems Installation Manual AM18-Q0626 | v1.0 | 2012.09
4 Installing a Recessed Mount
4.1 Overview
This chapter details how to install a recessed mount for the
IP200 MiniDome.
4.2 Installing the Recessed Mount
To mount to a recess mount, do the following:
1. Determine a secure location for the recessed mount.
Figure 4.1 Recess Mount Dimensions
NOTICE!
The image sensors in modern cameras are highly sensitive and
require special care for proper performance and extended
lifetime. Follow the guidelines for optimum results with your
camera:
– Do not expose to direct sunlight or bright spotlights in
operating and nonoperating conditions.
– Avoid bright lights in the field of view of the camera. Bright
lights cause a “smearing” effect, which is visible as white
lines above and below the highlight. Prolonged exposure to
bright lights may cause bleaching of the sensor's color
filters. This will be visible as colored spots in the picture
and is irreversible.
96 (3.78)
194 (7.64)
55.1 (2.17)

8en | Installing a Recessed Mount IP200 MiniDome In-Ceiling Mount
AM18-Q0626 | v1.0 | 2012.09 Installation Manual Bosch Security Systems
2. Drill or cut a 7 in. hole with a tolerance of +/- 1/8 in.
(177.8 mm +/- 2.2 mm).
3. Optional: if installing the camera to a suspended ceiling
tile or any other surface where additional support is
required, the LTC 9349MK mounting kit (sold separately)
is recommended. See the instruction book supplied with
the mounting bracket for installation instructions.
Figure 4.2 Mounting bracket
4. Align holes of mounting plate (supplied with dome) with
mounting bracket and attach with screws. Ensure that
both the crescent shape of the mounting plate and the
crescent shape of the mounting bracket are aligned.
5. Ensure that the clamping plates are angled inward by
pushing up and into the two slots.
6. Insert mount through the hole and into the ceiling. Slide
clamps out and down so that the drywall is clamped in
between the clamps and the bracket flange, 41.7 mm
(1.64 in.) maximum ceiling thickness and 9.7 mm (0.38 in.)
minimum ceiling thickness).

IP200 MiniDome In-Ceiling Mount Installing a Recessed Mount | en 9
Bosch Security Systems Installation Manual AM18-Q0626 | v1.0 | 2012.09
Figure 4.3 Attach Recess Mount to Ceiling
Figure 4.4 Attach Recess Mount to Ceiling
7. Tighten both clamps to the ceiling using supplied screws
and a #2 Phillips screwdriver.

10 en | Installing a Recessed Mount IP200 MiniDome In-Ceiling Mount
AM18-Q0626 | v1.0 | 2012.09 Installation Manual Bosch Security Systems
Figure 4.5 Tighten Mounting Clamps
NOTICE!
Over torquing the ceiling clamps can damage the clamp or
ceiling. Only tighten the clamp until it contacts the ceiling and
you start to feel some resistance. If using a power screwdriver,
set the torque level to the lowest setting.