Bosch GTA50W Assembly instructions

Operating / Safety Instructions
Consignes d’utilisation / de sécurité
Instrucciones de funcionamiento y seguridad
Call Toll Free for Consumer Information & Service Locations
Pour obtenir des informations et les adresses de nos centres de service après-vente, appelez ce numéro gratuit
Llame gratis para obtener información para el consumidor y ubicaciones de servicio
For English Version
See page 2 ●Version française Voir page 12 ●Versión en español Ver la página 22
IMPORTANT
Read Before Using ●IMPORTANT Lire avant usage ●IMPORTANTE Leer antes de usar
1-877-BOSCH99 (1-877-267-2499) www.boschtools.com
GTA50W
1609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 11609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 1 4/26/2023 11:32:11 AM4/26/2023 11:32:11 AM

-2-
Safety Instructions
Read all instructions. Failure
to follow all instructions listed
below may result in serious personal injury.
Fully assemble and tighten all the fasteners re-
quired for this stand. Periodically check that all
fasteners are attached and adjusted according to
the assembly instructions included in this manu-
al. A loose stand is unstable and may shift in use
and cause serious injury.
Turn tool switch off and disconnect power before
mounting to the stand. Unintended startup during
assembly can cause injury.
Before operating make sure the entire unit is
placed on a solid, at, level surface. Serious in-
jury could occur if tool is unstable and tips.
Never stand on tool or its stand or use as lad-
der or scaffolding. Serious injury could occur if
the tool is tipped or the cutting tool is accidentally
contacted. Do not store materials on or near the
tool such that it is necessary to stand on the tool
or its stand to reach them.
Use only Bosch replacement parts. Any others
may create a hazard.
The denitions below describe the level of severity for each signal word.
Please read the manual and pay attention to these symbols.
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
Safety Symbols
SAVE THESE INSTRUCTIONS
1609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 21609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 2 4/26/2023 11:32:11 AM4/26/2023 11:32:11 AM

-3-
You have purchased a Bosch Table Saw Stand
GTA50W, designed for job site use. This unit sets
up and folds quickly, and is easily loaded or un-
loaded by one person into a truck.
Before You Assemble This Table Saw
Stand
(Fig. 1, Fig. 2)
Sort out and account for all parts to make sure
that you have all necessary materials to assemble
your stand. Do not discard packing material until
all parts are accounted for.
Table Saw Stand Parts
Item Qty. Part Description
A 1 Handle Bar
B2Wheel
C 1 Saw Mounting Bar
D 1 Mid Pivot Bar
E 1 Wheel Bar
F 1 Left Linkage Bar
G 1 Right Linkage Bar
H 1 Support Bar Right
I 1 Support Bar Left
J 1 Lower Cross Bar
Tools Required:
• 13 mm and 17 mm openings on blade wrench
(included on table saw)
• 5 mm hex wrench (included on table saw)
Pre-Assembly
A
B
B
C
D
F
G
H
I
E
J
Fig. 1
1609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 31609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 3 4/26/2023 11:32:12 AM4/26/2023 11:32:12 AM

-4-
Pre-Assembly
Stand Assembly Hardware
(packaged in six bags connected together)
Part Description Specs. Qty.
Bag A
Flat Washer ⌀30 x ⌀13 x 3 mm 4
Lock Nut M12 2
Bag B
Hex Head Bolt M10 x 15 mm 2
Bag C
Hex Head Bolt M8 x 45 mm 6
Lock Nut M8 6
Rubber Thread Cap n/a 2
Bag D
Foot Pad n/a 2
Hex Head Bolt M8 x 60 mm 2
Flat Washer ⌀16 x ⌀18.2 x 1.5 mm 2
Lock Nut M8 2
Bag E
Hex Head Bolt M8 x 80 mm 8
Flat Washer ⌀16 x ⌀18.2 x 2.5 mm 16
Lock Nut M8 8
Rubber Thread Cap n/a 2
Bag F
Hex Head Bolt M8 x 110 mm 2
Flat Washer ⌀16 x ⌀18.2 x 2.5 mm 4
Lock Nut M8 2
Bag A
Bag B
Bag C
Bag D
Bag E
Bag F
Fig. 2
1609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 41609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 4 4/26/2023 11:32:12 AM4/26/2023 11:32:12 AM

-5-
Step 2. Attach Linkage Bars to Wheel
Bar
(Fig. 4)
All the hardware needed for this procedure is in
Bag B.
1. Mount the Left Linkage Bar Fon the welded
bushing of the Wheel Bar E.
2. Using the 5 mm hex wrench included on the
table saw, securely tighten the Hex Head Bolt
into the welded bushing.
3. Repeat the steps above for the Right Linkage
Bar Gassembly.
Note: The Right Linkage Bar G features a welded
pin while the Left Linkage Bar F does not.
Assembly
Step 1. Attach Wheels
(Fig. 3)
All the hardware needed for this procedure is in
Bag A.
1. Mount one (1) Flat Washer and the Wheel Bon
the axle of the Wheel Bar E.
2. Place one (1) Flat Washer on the threaded end
of the wheel axle. Thread the Lock Nut on the
threaded end of the wheel axle by hand.
3. Using the 17 mm opening on the blade wrench
provided with the table saw, tighten the Lock
Nut until the Washer does not move freely. Spin
the Wheel Bto check tightness. If the Wheel B
doesn’t turn freely, loosen the Nut by 1/8 to 1/4
of a turn.
4. Repeat the same steps with the other Wheel B.
F
G
E
Fig. 4
E
B
Fig. 3
1609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 51609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 5 4/26/2023 11:32:13 AM4/26/2023 11:32:13 AM

-6-
Step 3. Attach Linkage Bars to
Support Bars
(Fig. 5)
All the hardware needed for this procedure is in
Bag C.
1. Insert the end of the Left Linkage Bar Finto the
Left Support Bar Hand align the holes of both
bars.
2. Insert two (2) Hex Head Bolts through the holes
of the Left Linkage Bar F and Left Support Bar
H. Install two (2) M8 Lock Nuts, and use the
5 mm hex wrench and the 13 mm wrench open-
ing on the blade wrench (included on table
saw) to securely tighten the hardware.
3. Repeat the steps above for the Right Linkage
Bar G and the Right Support Bar I.
Step 4. Attach Lower Cross Bar to
Support Bars
(Fig. 6)
All the hardware needed for this procedure is in
Bag D.
1. Insert the ends of the Support Bars Hand Iinto
the Lower Cross Bar J, and align the holes of
both bars.
2. Place one (1) Flat Washer and one (1) Foot
Pad on one (1) Hex Head Bolt. Insert the Bolt
through the holes in the Left Support Bar H and
the Lower Cross Bar J. Install one (1) M8 Lock
Nut, and use the 5 mm hex key and a 13 mm
wrench to securely tighten the hardware.
3. Repeat the step above for the Right Support
Bar I and the Lower Cross Bar J.
Assembly
H
I
J
J
H
Fig. 6
F
G
I
H
Fig. 5
1609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 61609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 6 4/26/2023 11:32:13 AM4/26/2023 11:32:13 AM

-7-
Step 5. Attach Handle Bar to Lower
Cross Bar Assembly
(Fig. 7)
All the hardware needed for this procedure is in
Bag C.
1. Insert the ends of Handle Bar Ainto the Link-
age Bars Fand Gand align the holes of both
bars.
2. Insert two (2) Hex Head Bolts through the
holes of the Handle Bar A and Linkage Bars F
and G. Install one (1) Lock Nut, and use the 5
mm hex wrench and a 13 mm wrench to secure-
ly tighten the hardware until the parts cannot
move freely.
3. To cover the Bolt threads in the Handle area,
place the Rubber Thread Caps on the ends of
the Hex Head Bolts.
Step 6. Attach Mid Pivot Bar to Wheel
Bar Assembly
(Fig. 8)
All the hardware needed for this procedure is in
Bag E.
1. Insert a Hex Head Bolt through the hole on the
left side of the Wheel Bar E, then through one
(1) at washer, and then through the Mid Pivot
Bar D.
2. Place one (1) Flat Washer on the Hex Head Bolt.
Install one (1) Lock Nut, and use the 5 mm hex
key and a 13 mm wrench to securely tighten the
hardware until the parts cannot move freely.
Then loosen the Nut by 1/8 to 1/4 turn.
Note: To ensure that the joint is not overtight-
ened, ensure that the middle Flat Washer is
able to spin freely.
3. Repeat the steps above for the right side of the
assembly.
Assembly
F
G
A
Fig. 7
E
D
E
D
Fig. 8
1609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 71609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 7 4/26/2023 11:32:13 AM4/26/2023 11:32:13 AM

-8-
Assembly
Step 8. Attach Saw Mounting Bar to
Linkage Bar Assembly
(Fig. 10)
All the hardware needed for this procedure is in
Bag E.
1. Insert a Hex Head Bolt through the Left Linkage
Bar F, then through one (1) Flat Washer, and
then through the Saw Mounting Bar C.
2. Place one (1) Flat Washer on the Hex Head Bolt.
Install one (1) Lock Nut, and use the 5 mm hex
key and a 13 mm wrench to securely tighten the
hardware until the parts cannot move freely.
Then loosen the Lock Nut by 1/8 to 1/4 turn.
Note: To ensure that the joint is not overtight-
ened, ensure that the middle washer is able to
spin freely.
3. To cover the Bolt threads in the Handle area,
place the Rubber Thread Caps on the ends of
the Hex Head Bolts.
4. Repeat the steps above for the right side of the
assembly.
Step 7. Attach Saw Mounting Bar to
Mid Pivot Bar Assembly
(Fig. 9)
All the hardware needed for this procedure is in
Bag F.
1. Insert a Hex Head Bolt through the hole on
the left side of the Saw Mounting Bar C, then
through one (1) Flat Washer, and then through
the Mid Pivot Bar D.
2. Place one (1) Flat Washer on the Hex Head Bolt.
Install one (1) Lock Nut, and use the 5 mm hex
key and a 13 mm wrench to securely tighten the
hardware until the parts cannot move freely.
Then loosen the Lock Nut by 1/8 to 1/4 turn.
Note: To ensure that the joint is not overtight-
ened, ensure that the middle Flat Washer is
able to spin freely.
3. Repeat the steps above for the right side of the
assembly.
C
D
C
D
Fig. 9
C
F
F
C
G
Fig. 10
1609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 81609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 8 4/26/2023 11:32:14 AM4/26/2023 11:32:14 AM

-9-
Mounting Bosch GTS15-10 Table Saw
to GTA50W Stand
(Fig. 11)
All the hardware needed for this procedure is in
Bag E.
1. Align the saw as shown in Fig. 11.
2. Insert one (1) Hex Head Bolt through one (1)
Flat Washer, the mounting hole in the table
saw, and through the Saw Mounting Bar Cof
the stand.
3. Place one (1) Flat Washer. Install one (1) Lock
Nut, and use the 5 mm hex key and a 13 mm
wrench to securely tighten the hardware.
4. Repeat the steps above for the three remaining
mounting holes.
Mounting Table Saw to Stand
C
C
Fig. 11
1609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 91609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 9 4/26/2023 11:32:14 AM4/26/2023 11:32:14 AM

-10-
Lower Stand
(Fig. 12, Fig. 13)
1. Press the Foot Pedal 1, then pull back on the
stand slightly to disengage.
2. With both hands on the Handle 4, pull back
and lower the stand until it locks in position.
Fold Stand Upright
(Fig. 12, Fig. 13)
Keep ngers clear of hinge
points when folding or unfold-
ing the stand.
1. Press the Foot Pedal 1to release the Hook 2
from the Locking Pin 3.
2. With both hands on the Handle 4, pull up and
push forward on the stand until it locks in the
upright position.
Operating Instructions
1
3
2
4
Fig. 12
5
Fig. 13
1609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 101609B08221_GTA50W_Table_Saw_Stand_OSI_20230426.indd 10 4/26/2023 11:32:16 AM4/26/2023 11:32:16 AM