Bosch VIP-X1XF User manual

VIP X1 XF
VIP-X1XF
en Quick Installation Guide

VIP X1 XF Table of Contents | en i
Bosch Sicherheitssysteme GmbH Quick Installation Guide F.01U.269.739 | V3 | 2014.03
Table of Contents
1 About this Quick Installation Guide 1
2 Parts included 2
3 Unpacking 3
4 Installation 4
4.1 Preparing for wall-mounting 4
4.2 Mounting the frame 5
4.3 Placing the unit in the frame 6
5 Connection 7
5.1 Connecting the camera and audio 7
5.2 Creating a serial connection 8
5.3 Alarm and relay connections 9
5.4 Establishing the network connection 10
5.5 Connecting the power supply 11
6 Assigning an IP address 12

ii en | Table of Contents VIP X1 XF
F.01U.269.739 | V3 | 2014.03 Quick Installation Guide Bosch Sicherheitssysteme GmbH

VIP X1 XF About this Quick Installation Guide | en 1
Bosch Sicherheitssysteme GmbH Quick Installation Guide F.01U.269.739 | V3 | 2014.03
1 About this Quick Installation Guide
This Quick Installation Guide applies to all variants of the
VIP X1 XF.
For further detailed information, please see the extensive
online Help for the VIP X1 XF.
This Quick Installation Guide, the Installation and Operating
Manual and the current firmware package are available in
various languages at www.boschsecurity.com.
WARNING!
You should always make yourself familiar with the required
safety measures (see Safety document enclosed).
Only operate the VIP X1 XF in combination with an LPS/NEC
Class 2 power supply unit with limited output.
This Quick Installation Guide only describes the basic
procedure for installing a VIP X1 XF and cannot replace the
complete manual.

2en | Parts included VIP X1 XF
F.01U.269.739 | V3 | 2014.03 Quick Installation Guide Bosch Sicherheitssysteme GmbH
2 Parts included
– 1 VIP X1 XF network video server
– 2 terminal blocks
– 4 self-adhesive elastic bumpers
– 1 wall-mounting panel
–2screws
– 2 wall plugs
– 1 Quick Installation Guide
– 1 Safety Hints

VIP X1 XF Unpacking | en 3
Bosch Sicherheitssysteme GmbH Quick Installation Guide F.01U.269.739 | V3 | 2014.03
3 Unpacking
– Check that the delivery is complete and in perfect
condition.
– Arrange for the unit to be checked by
Bosch Security Systems if you find any damage.

4en | Installation VIP X1 XF
F.01U.269.739 | V3 | 2014.03 Quick Installation Guide Bosch Sicherheitssysteme GmbH
4 Installation
4.1 Preparing for wall-mounting
You can secure the VIP X1 XF to any load-bearing wall using the
wall-mounting panel, in either a vertical or a horizontal position.
CAUTION!
If mounting the unit in a vertical position, you will need to use
the lower plastic frame and then place the unit onto the frame
from above. If mounting the unit in a horizontal position, you
can use either of the two frames.

VIP X1 XF Installation | en 5
Bosch Sicherheitssysteme GmbH Quick Installation Guide F.01U.269.739 | V3 | 2014.03
4.2 Mounting the frame
– Lift the plastic frame on one side of the housing and
carefully remove it from the unit.
– Screw the plastic frame in the required position together
with the wall-mounting panel.
– Check that the plastic frame is secure.
CAUTION!
The mounting location must be able to reliably hold the unit.
The load-bearing capacity must be adequate for four times the
weight of the unit.

6en | Installation VIP X1 XF
F.01U.269.739 | V3 | 2014.03 Quick Installation Guide Bosch Sicherheitssysteme GmbH
4.3 Placing the unit in the frame
– Place the unit on the wall-mounting panel, with the panel
positioned between the housing and the second plastic
frame.
– Slide the unit into the plastic frame until you feel it lock
securely into place.
– Finally, check that the unit is securely attached in the
installation location.