Boshel BATC-001 User manual

◎Package includes
1 x Remote Controller
1 x Receiver Collar
1 x Adjustable Belt
1 x Test Bulb
1x USB Charging Cable
1 x Recharger
2 x Set of Metal Probes
1 x Button Opener
1 x User Guide
◎Controller
◎Features
1. 100 levels of vibration.
2. 100 levels of static shock.
3. The levels can be altered by use of up & down button.
4. Atone button activates a tone on the receiver collar.
5. The system can be used for 1 or 2 receiver collars. (Only 1 collar and
receiver included).
6. Remote range up to 300 meters.
7. LCD display
8. Backlight buttons
9. Rechargeable and waterproof
-1-

◎Power Saving
1. The Receiver Collar will TURN OFF if is unused for 4 minutes.
2. Any movement will activate the Receiver Collar into STANDBY MODE.
3. The Controller will go into STANDBY MODE if there is no operation after 20
seconds and turn off after 2 minutes.
◎Charging The Rem ote Controller
1. Charge the Controller by Connecting the charger connector to the charging
jack
2. After you plug the charger into a standard outlet, The red LED light on the
Transmitter will be lighted
3. Charge the Controller at least 6 hours for the first charge.
4. After fully charged, the red LED light will be a darker red.
◎Charging The Receiver
1. Charge the receiver by connecting the charger connector to the charging
jack.
2. After plugging the charger into a standard outlet, the red LED light inside
the Collar Receiver will be lighted.
3. Charge the Collar Receiver at least 6 hours for the first charge.
4. After fully charged, the red LED light will be turned off automatically.
-2-

Controller Enters sleep mode after 2-
3m of no
operation Press Mode for 1s to wake
up
Receiver
Collar
Lights up once per 5s when working
Enters sleep mode after 20s of no
movement
Apply any movement to
wake it up
Low battery indicator: the symbol will show up on the right down side of the
LCD screen.
◎Install The Receiver’s Contact Column
Choose the right column for your dog between the tall one and short one, According to the
size of the dog and their hair length.
-3-

◎How To Use The Controller.
1. After charging is completed press the “mode” button on the
controller.
2. Make sure that it is set to channel “1” (confirm on the LCD display).
Press the “reset” button on the receiver collar you should hear
3.
a “beep”.
4. Press the “y” button on the controller you should hear another
beep. That means that the receiver and the controller have successfully
paired.
Note: If you don’t hear the beep, please press the “reset” button on the
receiver collar once again, and try the above steps.
Note: since this package contains only 1 receiver, you should always make
sure when you use it that it is set to channel “1”
-4-

5. Press the up and down buttons for collar on the right side to set
levels.
Note: If you fail to press the “Y” button after hearing the beep from the
receiver collar, you need re-sync and start with pressing the “Reset” button of
the receiver collar.
◎TESTING THE TRAINING SYSTEM
The following methods are a testing system for you to see whether this
training system functions properly. Please make sure that the remote
and the receiver collar have been synced successfully by following the
prior steps.
1. Testing The Beep Function
Press the “Mode”button on the Controller, to set it on Beep Mode.
Note: Every time you press the “Mode” button it will change to another mode,
so make sure that it is on the desired mode by checking on the LCD screen.
Press the “Y” button and the receiver collar will beep, that means that the
Beep Function works properly.
-5-

2. Testing The LED Function
Press the “Mode”button on the Controller, switch to LED Mode.
Note: Every time you press the “Mode” button it will change to another mode,
so make sure that it is on the desired mode by checking on the LCD screen.
Press the “Y” button and then the receiver collar will flash, signifying that the
LED Light function works.
3. Testing The Vibration Function
Press the “Mode”button on the controller, switch to Vibrate Mode.
Note: Every time you press the “Mode” button it will change to another mode,
so make sure that it is on the desired mode by checking on the LCD screen.
Confirm on the LCD display that the level is not set to 000, press the
UP/DOWN button to adjust the intensity level, set anywhere from 1 to 100.
Press the “Y” button, the Receiver collar will vibrate, that means that the
Vibration function works properly.
-6-

4. Testing The Static Shock Function
Take out the test bulb from the plastic package and wind its metal wire on the
Receiver collar’s contact points.
Press the “Mode” button switch to Shock mode.
Note: Every time you press the “Mode” button it will change to another mode,
so make sure that it is on the desired mode by checking on the LCD screen.
Confirm on the LCD display that the level is not set to 000, press the
UP/DOWN button to adjust the intensity level, set anywhere from 1 to 100.
Press the ”Y” button and the test bulb will flash, that means that the static
shock function works properly.
◎Thread the collar strap throug h the slots on the receiver.
-7-

◎Notes for use:
1. The lifetime of the batteries vary according as how often you use the product.
Therefore you should often check the batteries by hearing the beep from the
Receiver Collar and watching the indicator sign on the LCD screen of the
Transmitter.
2. The valid distance of the Controller means the straight-line distance between the
Controller and the Receiver Collar without obstacles in between. If there are
interference signals or signal screening around, the actual remote Controller
distance may vary.
3. The waterproof level of the receiver is IP3 that means that it could withhold rain,
even heavy rain, but putting the receiver in a cup of water will damage the receiver,
so don’t let your dog swim with it.
4. The waterproof level of the controller is IP2 that means it could withhold rain drops
or light drizzling, so don’t let it exposed to heavy rain.
5. When your dog is wearing the receiver, always make sure that the button holes are
covered with the rubber especially in the rain, as it causes damage if it’s open. (Tip:
Use the included pin to help tighten the rubber in to the holes).
6. After the receiver was exposed to water let it dry out for a few hours in a dry place.
7. This product is for pet training. Only by training, the pet can understand the
intention of its owner. Good effect can only be achieved after a period of training.
8. Training sessions should be kept positive and short, about 10-15 minutes long each
time.
Presently, this product is the most effective and safest tool for training your pet.
Following the correct operational instructions, you can effectively train the pet and
bring it no harm.
Warnings:
1. Before using this collar, you should always check under the dog's
neck to make sure there's no wound.
2. Do not let your pet constantly wear this collar; take it down when
you’re not training them.
3. Do not use this collar to connect your leash hook, use a separate
collar or harness for your leash hook.
4. Keep away of reach of children and pets.
5. Do not let your pet chew on it.
6. If you see any unusual behavior on your pet
by using this product, immediately stop
using this product and consult a vet.
-8-

Thanks for shopping Boshel® we really appreciate your business and we’re sure
that you and your pets will enjoy the new product.
As a growing company striving for perfection, your feedback is crucial for us,
If you would be able to leave us your feedback it would be a great help and
would be greatly appreciated. So please take the 2 minutes to rate our product
on Amazon.com or any other marketplace you purchased this product. It will
help us serve you better.
As a valued customer of Boshel you benefit from outstanding
unparalleled customer service. So if you are not completely satisfied or if
the product hasn’t met your expectations or if you have any
questions/problems/concerns/comments please do not hesitate to
contact us @ [e-mail] we will go out of our way to assist
you. All messages are being answered within 48 business hours (usually
less than 12 hours).
p.s. please do not contact us via the messaging system on the marketplace you bought
the product, all messages should please be sent directly to the email address provided
above or through the contact form on www.Boshel.com
This product is backed by a 1 year limited warranty, to enroll in the warranty
program simply fill out the warranty application online @ www.Boshel.com
Please note: The warranty is only valid when you purchase the product from
our exclusive sellers, they are either, BoshelDirect, or Amabus, or
Deals2Reveal, all others might be counterfeit, and are not backed by our
warranty.
Love what you purchased? Try our other products and be even more
thrilled!
Visit www.Boshel.com today to see our rapidly growing collection for all your pet
needs.
Thanks for your business and enjoy your pets!
-9-