BOW Bureau Heathrow Plus User manual

Bureau
Heathrow Plus
User manual
ENG 1
1
3
8
2
10
9
12
6
7
4
5
11
Component list
Install the supporting beam
and the side bracket
No. Part Qty No. Part Qty
1222
3
Connection rod
24
Left
Supporting Beam
2
5
Right
Supporting Beam
26
Side bracket
2
7
Adapter arm
18
Adapter
1
9
Control Box
112
Handset
(Option)
1
11
Adapter cable
112
Power Plug
1
Accessory list
Technical data
Column Stage 3
Max. Weight Capicity 100 KG
Height Range 620-1279 mm (Without tabletop)
Width Range 1100 - 1700 mm
Attention: The drawings below are for guidance only
and they may dier slightly from the product and
ttings received. Please contact our customer service
department if you have any queries.
If the connecting rod cannot be inserted
into the supporting beam, please loosen the
screws on the beam.
Using screws (A) to connect the side bracket (6) with the
left supporting beam (4) and the right supporting beam
(5), and tighten them with the allen key (G).
Using screws (B) to connect the lifting column (2) with the
left supporting beam (4) and the right supporting beam
(5), and tighten them with the allen key (G).
Connect the feet(1) and the lifting column (2) with screws
(C), and tighten them with the allen key (G).
Using screws (A) to connect the connection rod (3) with
the left supporting beam (4) and the right supporting
beam (5), and tighten them with the allen key (G).
No. Image Spec Qty
A M6 4
B M6 8
C M6 8
D St 4.2 6
E Cabletie 6
F St 4.2 16
G Allen Key 4x4 mm 1
bowtout.com
5
3
4
G
A
6
4
5
Ax4 G
4x4
2
3
Install the lifting column
Install the feet
G
B
2
5
4
Tighten it
Bx8 G
4x4
Cx8 G
4x 4
G
C
2
1

The following tips will help you detected and eliminate the common fault and
error. If the fault you met is not listed below, please contact with your supplier.
Only themanufacturer and professionals are capable for investigating and
correcting those fault and error.
4
G
4x 4
5Install the tabletop, handset,
control box & adapter
Bx8
6Connect cables to the control box
Dx6 Ex6
Attention
Waste disposal
Buton Introduction
Common fault treatment
1. Power supply: AC100V-240V,50/60Hz
2. Service Environment: 0-40°C
3. Unplug the power plug before cleaning, wipe the dust on surface with slight wet dishcloth
when cleaning, be careful not to let the drops into the internal parts, not loose the connector.
4. The electric box contains electronic components, metals, plastics, wires etc., so dispose of it
in accordance with each country’s environmental legislation, not the general household waste.
5. Check carefully to ensure correct and complete assembly before using.
6. Be familiar with all functions and program settings of the product before rst use.
7. Children are forbidden to play on the product because of unforeseen action when playing, so
any dangerous consequences caused by this improper action will not be on manufacturers.
8. Slight noise caused by the V-ribbed belt or brake system due to structure will not have any
eect on the use of the equipment.
9. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure that the
cleaner used will not pollute the environment.
10. This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance.
11. Cleaning and user maintenance shall not be made by children without supervision.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a
similarly qualied person in order to avoid a hazard.
13. Please make sure there is no hazard sources in your operating environment. e.g., do not
litter the tools around. Always be careful to treat the packaging materials in order to avoid any
possible danger, e.g. plastic bag may lead to choking hazard to children.
14. Keep the original package of the equipment if necessary in case of the future use in
transportation.
This marking indicates that this product should
not be disposed with other household wastes.
To prevent possible harm to the environment or
human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable
reuse of material resources. To return your used
device, please use the return and collection
systems or contact the retailer where the
product was purchased. They can take this
product for environmental safe recycling.
Height Adjustable Function:
Press the or button to adjust the height. The LED display shows the current
height.
Height Memory Function:
a. Adjust up or down to the desired height. Press “M” to save the height, and the screen
will display “5-“;
Press , , “3” or “4” then to save the height to the corresponding position 1 or 2
or 3 or 4 , “5-1“, “5-2“, “5-3“ or “5-4“ will nally be showed on the display as a result.
b. Press or or “3” or “4” button directly to automatically adjust the memory height
you saved.
Anti-collision sensitivity adjustment - optional features:
a. Press and hold the button for 5 seconds at the same time to switch the
sensitivity which is devided in to four levels, A-3,A-2,A-1,A-0. Switch one sensitivity level
by a single operation.
b. When the display shows “A-0” , the anti-collision function is o; “A-1”, refers to
low sensitivity; “A-2”refers to medium sensitivity; “A-3”refers to high
sensitivity; (factory default is A-3);
c. During height adjustment, when tabletop touches obstacles, it will instantly rebound
to avoid damage.
d. Press and hold the button for 5 seconds at the same time. If the display
does not show any code above, there is no anti-collision function.
Troubleshooting:
a. When the LED display shows “A5Γ“ or “r5t“, long press the down button , and
wait for the height reaches the top or the bottom, then runs in reverse until it stops, at
this time the display shows the height number, release the down key ,
the reset is nished, and the desk can be used normally;
b. If the display shows “E01” or “E02 “. Please let the table rest for more than 18 minutes
before it can be used normally.
c. When reporting other error codes, and no response occurs ,please ensure the
connection cable can work normally without damage, then power it o for more than 10
seconds. “A5Γ“ or “r5t“ will show after reconnecting power, then long press the down
key to reset.
d. If you perform the above operations, the desk still does not work properly, please
contact customer service.
: Adjust the desk upwards
: Adjust the desk downwards
: Position 1, rst height position saved by the user
: Position 2, second height position saved by the user
3: Position 3, third height position saved by the user
4: Position 4, fourth height position saved by the user
M: Height memory function
Fix the cables to the tabletop
with cable management (E),
and then use screw (D) to x
the cable management (E)
to keep the desk cables
organized.
7
4
Loosen
Adjust
Tighten
The expansion distance of the
supporting beam can be adjusted
according to the actual use.
Buckle the adapter arm (7) into the left supporting
beam before open the tabletop(4).
F
10
8
7
9Fix the tabletop with screws (F), and then to x
the control box (9) on the tabletop with screws (F).
The handset (10) is xed on the tabletop with
self-owned screw and insert the adapter
into the adapter arm.
The expansion of supporting
beam cannot exceed this hole.
8
7
Insert
10
1
1
1
12
8
9
11
Tear off Manage
cables Fix cables
DC
HS M1 M2
Port for
handset
Port for
adapter cable
Port for cable
connected to
the lifting column
Fault phenomenon Method
No response while long pressing down arrow after
connected witha power supply
Check if all the cables be connected well
Contact your supplier or dealer
No response while pressing up arrow/ down arrow
after connected with a power supply
Check if all the cables be connected well
Contact your supplier or dealer
Rising in a low speed Check if overloaded, max loading: 100kg;
Contact your supplier or dealer
The motor not move as instructed Contact your supplier or dealer
Go down but not go up Reposition
Contact your supplier or dealer
Downward sliding Check if overloaded, max loading: 100kg;
Contact your supplier or dealer
Frequently Reposition Check if overloaded, max loading: 100kg;
Contact your supplier or dealer
Overwork
(Duty cycle: Max 2min on/18min OFF)
Restart after suspend for 18mins while
connecting with power;
Contact your supplier or dealer;
Not enough up&down height Press “M”and “3” together for 3 seconds or more, after hearing conti-
nuous beeping for twice, it will restore factory settings
Contact your supplier or dealer
Install the adapter arm
iOperation Instruction
LED Display