Furniture of America HFW-1476C4 User manual

HFW-1476C4
Page 1 of 13 REV.14-12-15

Page 2 of 13

Page 3 of 13

Page 4 of 13

Page 5 of 13
CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS

CONSOLE TABLE
ASSEMBLY INSTRUCTIONS MODEL # HFW-1476C4
please keep for future reference PARTS LIST
HARDWARE LIST
1PC
124PCS
DIMENSIONS : 39.4"(W)*11.8"(D)30.5"(H)
Page 6 of 13
B1PC
A
2PCS D2PCS
E1PC
F2PCS
G2PCS
H2PCS
1PC J1PC
I1PC K1PC L
1PC 1PC
NM 1PC
1PC 1PCQ
P
O
2PCS
R
224PCS 330PCS 44PCS 52PCS 64PCS
72PCS 81PC 91PC 10 1PC 11 12PCS 12 6PCS
A
B
C
D
R
H
F
G
M
I
J
C
C

F
Hardware 3 x 20 pcs
Hardware 5 x 2 pcs
Hardware 6 x 4 pcs
STEP : 1
ASSEMBLY INSTRUCTIONS
Assembly Drawer's Runners (a.k.a. Rails, Glides, Slides or Guides)
An assembly of ONE drawer requires two sets of runners. The runner is composed of
an inner rail and outer slide. Please read completely first before assembling.
Mounting the Inner Rail (Fixed) of the Runner: Before mounting, please determine
which side of the panel is the front and rear. The single screw hole on the outer slide
MUST be positioned on the FRONT of the panel. Place the inner rail of the runner in
its correct position and flat on its back. Slide the outer slide out to the way to align the
center or second holes on both ends of the inner rail with the pre-drilled holes on the
panel. For most applications, the center or second holes are used but if not, just make
sure the appropriate rail holes are aligned up with the panel holes. Use two screws to
secure the inner rail of the runner onto the panel.
Mounting the Outer Slide (Moveable) of the Runner: Each outer rail is secured with
a single screw onto the FRONT SIDE of drawer. Extend the two outer sliders of the
runners and place the drawer in between those two outer slides. Align the pre-drilled
holes on each side of the drawer with the screw holes of the outer slides. Use two
screws to secure from the inside of the drawer into the screw holes of the outer slides.
Page 7 of 13

ASSEMBLY INSTRUCTIONS
STEP : 2
STEP : 3
Page 8 of 13
Hardware 2 x 4 pcs
Hardware 1 x 8 pcs
STEP : 4
Hardware 1 x 4 pcs
Hardware 2 x 4 pcs
Hardware 3 x 4 pcs
Dowel hole

ASSEMBLY INSTRUCTIONS
Page 9 of 13
STEP : 5
Hardware 11 x 2 pcs
STEP : 6
Hardware 2 x 4 pcs
Hardware 11 x 2 pcs Dowel hole

Page 10 of 13
STEP : 7
STEP : 8
Hardware 1 x 2 pcs
Hardware 3 x 2 pcs
Hardware 11 x 4 pcs
Dowel hole
ASSEMBLY INSTRUCTIONS
Hardware 12 x 6 pcs

ASSEMBLY INSTRUCTIONS
STEP : 9
STEP : 10
Hardware 2 x 2 pcs
STEP : 11
2
Hardware 11 x 4 pcs
Hardware 1 x 2 pcs
Hardware 2 x 2 pcs
Hardware 3 x 2 pcs
Page 11 of 13

STEP : 12
Page 12 of 13
Hardware 1 x 6 pcs
Hardware 2 x 6 pcs
STEP : 13
Hardware 1 x 2 pcs
Hardware 2 x 2 pcs
Hardware 3 x 2 pcs
Hardware 4 x 4 pcs
Hardware 8 x 1 pc
Hardware 9 x 1 pc
A
N
O
P
M
M
ASSEMBLY INSTRUCTIONS
Dowel hole
Dowel hole

ASSEMBLY INSTRUCTIONS
STEP : 14
Page 13 of 13
Hardware 7 x 2 pcs
ASSEMBLY IS COMPLETED
Make sure the unit is rested on a flat
surface and does not feel loose or
wobbly. If it does, double check all
bolts/screws are secured and properly
tightened.
Extend the two outer slides of the runners so that they
are align with the sides of the drawer. Make sure the
pre-drilled holes from the drawer align with the screw
holes of the outer slides. Secure two screws from the
inside of the drawer using a Philips srewdriver to
tighten them to the outer sliders.