Argos 457/2156 Manual

HM Wide Media Unit
Care & Instruction Manual
Please read and retain these instructions for future reference
457/2156
651/5070

1
Safety and Care Advice
Important –Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Handy Hints
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.

2
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline:
Argos = 0345 6400800
Top panel (60.6 x 13.1cm)
1
Bottom panel (60.6 x 19.6cm)
2
Right side panel (111 x 13cm)
3
Left side panel (111 x 13cm)
4
Middle Shelf (use screw) (58 x 12.9cm)
5
Back panel (60 x 113cm)
9
Small support x 3 (14.9 x 12.8cm)
7
Large support x 6 ((20 x 12.8cm)
8
Shelf x 4 (use dowel) (58 x 12.9cm)
6
Finished front edge
Finished front edge
15.5 20.6
15.5 20.6

A B C
D
G
E F
3
Ruler - Use this ruler to help correctly identify the screws
Tools required
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or glue)
7mm Suitable drill bit
(for use with wall plug)
The screws length is measured from the head to the point (30mm screw shown).
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Components - Fittings
14mm Screw x 2
40mm Screw x 12 Nail x 2230mm Dowel x 56
Screw cover x 8
Wall plug x 2
Wall strap x 2
(This screw is
included in the
wall strap bag)
x 2

Step
Assembly Instructions
Insert dowels
1
4
a:
b:
X 3
X 6
X 4
3
4
7
8
6
a: Insert Dowels into
Right side panel and
Left side panel .
B
3
4
b: Insert Dowels into
Small support , Large
support and Shelf
.
B
7
8
6
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B

Attaching panels
Assembly Instructions
5
Continued on next page.
b:
a:
7
5
8
8
6
6
8
8
7
a: Position Small support
, Large supports
onto Middle shelf .
7 8
5
6
b: Position Shelves
onto unit.
Step 2 - continued
Finished front edge
Finished front edge

c:
d:
Assembly Instructions
Step 2 - continued
6
6
Continued on next page.
d: Position Shelves
onto unit.
7
c: Position Small
supports onto unit.
8
8
6
6
6
6
8
8
7
7
Finished front edge
Finished front edge

3
4
e: Use Screws to fix
Right side panel and
Left side panel onto
unit.
7
7
Assembly Instructions
Step 2 -
f:
e:
A
Use Screw covers to
cover the screw heads.
D
Continued on next page.
f: Position Small
support onto unit.
3
6
6
5
66
4
7
A
A
D
D
D
D
A
A
4
3
continued
Finished front edge
Finished front edge
15.5 20.6

Assembly Instructions
8
a:
b:
Continued on next page.
4
7
1
3
A
A
A
A
D
D
D
D
6
3
4
8
8
1
a: Use Screws to fix
Top panel onto unit.
A
Use Screw covers to
cover the screw heads.
D
Step 3
b: Position Large
supports onto unit.
8
Attaching Top and
Bottom panel
Finished front edge
Finished front edge

d:
a:
tructions
Assembly Instructions
9
Step 3 - continued
Step 4
48
8
2
9
3
A
A
A
A
C
back surface
2
a: Use Screws to fix
Bottom panel onto
unit.
A
Fixing back panel
Attach back panel
using nails .
C
9
Important:
The unit MUST
be ‘square’ when
back is attached.
Finished front edge
1
3