Häfele Tavoletto 271.97.300 User manual

Hiddenbed
Item No.: 271.97.300
Mounting Instructions

2
Follow these steps
to assemble your Hiddenbed
Assemble them together
Add a mattress.
Construct the 3 main parts
1 2
3
YOUR HIDDENBED IS READY!

3
Parts List
Body Parts
Part No. Name Qty Pg
1 Body Side L/R 2 1
2 Body Side Concealer 4 sets 2
3 Bottom Stretcher 1 3
4 Body Top 1 4
5 Top Stretcher 1 5
6 (*) Top Stiffener/Metal 1 -
7 Body Back 1 7
18 Bed Stop 2 18
* See item No.: 940.84.253
Bed Parts
Part No. Name Qty Pg
8 Bed head L/R 2 8
9 Slats Cover Sheet 1 9
10 Front Bed Rail 1 10
11 Rear Bed Rail 1 11
12 Bed Slats/Solid Wood 12 12
13 Slats Cleats 2 13
Desk Parts
Part No. Name Qty Pg
14 Desk Side L/R 2 14
15 Desk Top 1 15
16 Desk Back 1 16
17(*) Desk Stiffener /Metal 1 17
* See item No.: 940.84.253

4
MECH ARM
PLATE
2 pcs.
A2 A3 A4 A5 A6 A7
A1
A9A8 A10 A11
TRUNNION
BUSHING &
SCREW
2 pcs.
LOCKING PIN
WITH SCREWS
2 pcs.
H2, 7x70, Confirmat
Safety Bracket
Bumper, 10 x 20 mm
H14, #8 x 1 1/2”, Flat Head Wood Screw
H10, #8 x 2”, Flat Head Wood Screw
H9, #8 x 3/4”, Flat Head Wood Screw
H6, 1/4” - 20 x 2”, Flat Head Allen & T nut
H3, 1/4” - 20 x 1 1/4”, Carriage Bolt, Washer & Nut
Aluminum Stiffener for Body Top, 2035 mm Long 1
Aluminum Stiffener for Desk Top, 1909 mm Long 1
#8 x 5/8”, Pan Head Screw for Attachment 18
LOCK
BUSHING
4 pcs.
PIN BALL
2 pcs.
GAS SPRING
2 pcs.
LOWER
SUPPORT
2 pcs.
LOWER
SUPPORT
PIN
2 pcs.
COTTER
PIN
2 pcs.
TRIBEARER
2 pcs.
LINK PIVOT
2 sets
59
22
46
7
6
20
2
2
Component List
Mechanism Kit – Item No. 271.97.300
Hardware Kit – Item No. 450.19.400
Shelf Stiffener Kit – Item No. 940.84.253

5
Make sure that:
For best performance:
Unit is leveled; that both side panels are parellel and level.
Unit needs to be properly secured to the wall, see Häfele Item 271.98.100 safety
brackets (included in assembly hardware kit #450.19.400)
Stand at the middle when moving from bed to desk positions.
Keep fingers clear from closing parts.
Use a mattress with an approximate weight of 44 lbs (20 kgs) and a maximum
height of 10”.
Items placed on desk, should not exceed 55 lbs (25 kgs).
Use position “B” for pin arm, see body assembly diagram.
Using the above criteria, the effort to move from desk to bed positions should
take appoximately 20 lbs. of force.
Avoid excessive or off-center loads on desk.
Items left on desk cannot exceed 18” in height and 25 lbs. in weight.
Avoid trapping fingers in closing parts.
Use the locking pins to “lock” into desk or bed positions.
Make sure that electrical cords do not get pinched in any pivot points.
Pivot points should be periodicaly lubricated with WD-40 or similar.
IMPORTANT POINTS FOR SAFE AND RELIABLE OPERATION
WARNINGS
Use the Locking Pins on Desk Side to lock in
place in both bed and desk positions.
In general 2 people are required to assemble and
install this product.
Successful and safe installation of fiting set and construction of bed
requires a professional skill level. CNC equipment for panel processing
and accurate hole locations is mandatory; both vertical and horizontal
holes are required. MDF board is required as opposed to particleboard
to ensure strucural integrity.

6
Body Assembly
Arm pin outer
position for more
load on table
Arm pin inner
position for less
load on table
RIGHT SIDE SHOWN
Do the same with left side symmetrically
A
B
C
Attach the gas spring to mechanism arm by snapping over
ball pin.
1
2
Attach other side (blade side) of gas spring to
lower support (A3) using lower support pin
(A4), insert cotter pins (A5) and bend ends.
Cotter pin
3
Attach arm plate (A1) to the body side
using 8 sets of carriage bolts, washer
and nuts. Make sure the hook on arm
is facing upwards.
H3
4
Attach lower support (A3) to body side
using 2 sets of the carriage bolts,
washer and nuts.
Repeat steps above for the
opposite side.
A2
1
A3
4
A1
H3
H3
3
Hook to face upwards
Right hand side shown

7
Attach top stretcher (5) to body top (4) using 6 pcs #8 x 1 1/2“
wood screws. Attach metal top stiffener (6) 2035 mm long
under body top, directly behind top stretcher using 6 pcs .
repackaged #8 x 5 / 8 ” long pan head screws (H14).
Additional holes may have to be drilled in the aluminum
profile to accept screws.
H14
4
5
6
5
Attach bed stops (18) to body sides (1) using 2 pcs.
Confirmat screws per side (H2).
6
H2
1
18

8
Assemble body sides (1), body top (3), body back (7), and
bottom stretcher using Confirmat screws (H2, 28 pcs.).
7
H2
H2
5
7
3
8a
8a
8b
8b
8c
8c
1a
1b

9
Desk Assembly
1
Attach desk back (16) to desk top (15) using 4 pcs. Confirmat
screws (H2).
H2
15
16
2
Attach the tribearer (A6) to desk sides (14) using 3 pcs. Flat
Head & T nut (H6) and 1 pc. #8 x 3/4” (H9)on top hole of
tribearer.
14
A6

10
3
Attach metal top stiffener (17) 1909 mm long under desk top
approximately 6" from front edge using 6 pcs. re-packaged screws
#8 x 5/8” long pan head screws. Additional holes may have to be
drilled in the aluminum profile to accept screws.
15
14
4
14
H2
17
Attach sides (14) to desk top (15) using 8 pcs. Confirmat screws (H2).
15
14
H2

11
Bed Assembly
1
Attach front bed rail (10) and rear bed rail (11) to bed heads
(8) using Confirmat screws (H2).
Make sure that holes for affixing bed cleats are facing the
right direction, see technical drawings indicating bottom
sides.
8
10
8
Attach slat cleats (13) to bed rails using #8 x 1 1/2” flat head
screws (H14). Make sure that pilot holes for bed slats are
facing up (down in sketch position)
H2
Final Assembly
1
The link pivot sets (A7) come assembled together. Un-screw
and remove the plate from one side.
Do not attach slats cover or bed slats at this point,
they must be attached after bed and body is
assembled together.
11

12
2
3
Place the bed head assembly on top of desk top assembly as
shown below, and align holes for link pivot - see detail 2
below.
From the outside introduce the link pivot into holes as
shown, slightly raising the bed assembly to align holes.
Attach other plate onto the link pivot securely with remaining
screws. Make sure all screws are tight.
2
3
HEAVY - BE CAREFUL
4
Slide the body assembly over the bed assembly taking
caution that the arm mechanism does not scratch the sides
of body.
Align holes for trunion bushings (A8), install trunion bolt and
loosely tighten until other side is aligned and affixed.
Strongly tighten both trunion bolts.

13
H10
5
Place the 1/4” thick slats cover sheet (9) on top of slat cleats.
Place bed slats (12) over cover sheet, align holes.
Affix bed slats by driving screws through slats, through
cover sheet and into bed cleats using 24 pcs. #8 x 2" flat
head wood screws (H10)
H10
12
6
Attach the top portions of body side concealers only at this
point using #8 x 2" flat head screws (H10) (the bottom parts
are installed after arm mechanism is attached).
Pound in lock bushings (A10) in both sides of upper side
concealers. Install locking pins (A9) in desk sides with
included black screws.
9
A10
ATTACH TOP
ONLY AT THIS POINT
APPLY SLATS COVER SHEET
BEFORE BED SLATS.

14
7
Carefully lift the bed slowly keeping the desk in horizontal
position. Once in upper position, lock into place in both
sides by pushing in the locking pins.
Attach arm mechanisms to tribearer making sure it seats in
the slot - see diagrams below.
b9a9
PUSH IN
TO LOCK
CAUTION!
1- EXTRA STRENGTH REQUIRED
2- TAKE CARE OF YOUR FINGERS
Do not put fingers in the hook.
Hold the arm as shown.
8
9c
10
Be sure the unit is anchored properly to the wall. Use
the safety brackets as shown below, making sure wall studs
are used for attachment.
Add mattress (not included).
LLAW
1
Finish attaching bottom portions of body side concealers,
install lock bushing for bottom locking position.
Install rubber bumpers to bed stops using #8 x 1 1/2” flat head
screws - be sure bumpers align with side of bed as it meets
stops.
14

3901 Cheyenne Drive
P.O. Box 4000
Archdale, NC 27263
1-800-423-3531
www.hafele.com
Operation
• Make sure unit is leveled and properly anchored to the wall.
• Make sure the floor is cleared when lowering the bed.
• Stand at the middle when moving from bed to desk positions.
• To move from bed to desk positions, first unlock pins on both sides, then grab
front bed rail and slowly raise - be sure to keep fingers clear when reaching the top
position.
• To move from desk to bed position, first unlock pins on both sides, then grab front
bed rail with one hand and push down the desk with the other hand, be sure to
lock in position again.
• For convenience a handle can be placed under bed (on slats cover sheet) to
assist with moving from desk to bed.
• Hiddenbed system is based on a desk to bed balance. An unbalaned ratio may
result in having to apply extra force when moving from bed to desk and vice versa.
• Pin arm position on arm (A,B,C) may have to be adjusted to properly assist load.