BOXLIGHT P12 Installation instructions manual

1
P12 Projector Mounting Guide for Pen- and Non-Interactive Models
Introduction
This document provides positioning information for the P12I pen-interactive and P12N non-interactive projectors, enabling you to
determine the proper placement for the WXGA, 16:9, and ultra-wide models of the P12 projector. It is essential to reference the
correct table for the projector model and measurement units (millimeters or inches) when placing the wall bracket.
Note: This document is only for the pen-interactive and non-interactive models of the P12 projector. The positioning information
for the touch-interactive P12 models is on a separate document titled “P12 Touch-Interactive Projector Positioning Guide.”
Background
For the pen-interactive and non-interactive models of the P12 projector, the projected image can be positioned at the top of the
whiteboard’s projection surface. The wall mount bracket will produce an image of the desired size when the top of the wall plate
is positioned at a distance “O” as on the diagram below (outlined in red-dashes).
Figure 1
Positioning the Wall Bracket
It is essential to horizontally position the wall bracket as shown on the diagram at right. The left edge of the
wall bracket must be 0.5” (13mm) to the right of the intended image center. If the wall bracket is instead
centered on the whiteboard, which initially seems the likely placement, the displayed image will not be
centered and proper alignment will not be possible.
Vertical positioning of the wall bracket should be determined from the relevant table below based on the
intended image size and aspect ratio.
Mounting Arms
The 27” (697mm) WallMount-P12W is the model bundled with the WXGA and 16:9 models.
The longer 33” (841mm) WallMount-P12U is the model bundled with the P12 ultra-wide model.
Figure 2

2
Example
To produce the largest possible diagonal image at 16:10 aspect ratio on a frameless whiteboard:
• Measure the width and height of the projection surface. In this example, the measured width is 80” and the height is 48”.
• The WXGA 16:10 table below shows that a projection surface 48” in height can support up to a 90” diagonal image. The
table shows that the 90” diagonal image will be 76.3” wide, which leaves ≈7” of whitespace on the left and right sides if
the image is centered on the whiteboard.
• Determine the horizontal center of the intended image then mark a point 0.5” (13mm) to the right of this. This mark
defines the horizontal position of the left edge of the wall bracket.
• From the WXGA 16:10 table: Distance “O” from the top of the wall bracket to the top of this 90” diagonal projected image
is 13.9”.
• Mount the wall bracket so its top edge is 13.9” above the top edge of the whiteboard’s projection surface and the
bracket’s left edge is 0.5” to the right of the intended image center.
Figure 3
• Attach the projector to the projector mounting bracket. Leave the four bolts that hold the projector to the bracket slightly
loose so it can be adjusted horizontally.
• Attach the mounting arm with projector to the wall bracket. Leave the four bolts that secure the arm to the wall bracket
loose so the assembly can be adjusted vertically.
• The projector’s vertical position can be adjusted using the bolt (1/2”, 13mm) at the bottom of the bracket. Tighten the
bolts on the sides once the position is finalized.
• The projector can be adjusted horizontally ≈±1/2” (6mm) by sliding it within the projector mounting bracket. Tighten the
bolts once the position is finalized.
• Proceed to the alignment stage of the process below.
P12 Projector Mounting Guide for Pen- and Non-Interactive Models

3
Alignment
Figure 4
Figure 5
P12 Projector Mounting Guide for Pen- and Non-Interactive Models

4
P12 Projector Mounting Guide for Pen- and Non-Interactive Models

5
Printed Monday, December 19, 2016 10:43
AM
5
P12 Pen-Interactive and Non-Interactive Projector Positioning Tables
Diagonal
imagesize
(S)ininch
Imagewidth
(W)inin.
Imageheight
(H)inin.
Distance
fromsurface
of
whiteboard
tocenterof
projector
mount(T)in
in.
Distance
fromsurface
of
whiteboard
tobackof
projector(T1)
inin.
Distance
fromtopof
imagetotop
ofwallplate
(O)inin.
Distance
fromtopof
imagetotop
ofinterface
boss(O1)in
in.
Distance
fromtopof
imagetotop
ofprojector
(O2)inin.
85 72.1 45.0 14.6 9.2 13.5 10.5 9.7
86 72.9 45.6 14.8 9.4 13.5 10.6 9.8
87 73.8 46.1 15.0 9.6 13.6 10.6 9.8
88 74.6 46.7 15.2 9.8 13.7 10.7 10.0
89 75.5 47.2 15.5 10.1 13.8 10.8 10.0
90 76.3 47.7 15.7 10.3 13.9 10.9 10.1
91 77.2 48.2 15.9 10.5 14.0 11.0 10.2
92 78.0 48.8 16.1 10.7 14.1 11.1 10.3
93 78.9 49.3 16.4 11.0 14.2 11.2 10.4
94 79.7 49.8 16.6 11.2 14.3 11.3 10.5
95 80.6 50.4 16.8 11.4 14.4 11.4 10.6
96 81.4 50.9 17.0 11.7 14.5 11.5 10.7
97 82.2 51.4 17.3 11.9 14.6 11.6 10.8
98 83.1 51.9 17.5 12.1 14.7 11.7 10.9
99 83.9 52.5 17.7 12.3 14.8 11.8 11.0
100 84.8 53.0 18.0 12.6 14.8 11.9 11.1
101 85.6 53.5 18.1 12.8 15.0 12.0 11.2
102 86.5 54.1 18.4 13.0 15.0 12.0 11.3
103 87.4 54.6 18.6 13.2 15.1 12.1 11.3
104 88.2 55.1 18.9 13.5 15.2 12.2 11.5
105 89.1 55.7 19.1 13.7 15.3 12.3 11.5
106 89.9 56.2 19.3 13.9 15.4 12.4 11.7
107 90.7 56.7 19.5 14.1 15.5 12.5 11.7
108 91.6 57.2 19.7 14.3 15.6 12.6 11.8
109 92.4 57.8 20.0 14.6 15.7 12.7 11.9
110 93.3 58.3 20.2 14.8 15.8 12.8 12.0
111 94.1 58.8 20.4 15.0 15.9 12.9 12.1
112 95.0 59.4 20.6 15.2 16.0 13.0 12.2
113 95.8 59.9 20.9 15.5 16.1 13.1 12.3
114 96.7 60.4 21.1 15.7 16.2 13.2 12.4
115 97.5 60.9 21.3 15.9 16.3 13.3 12.5
P12WXGA(16:10)Wallmountinstallationmeasurementchart-inches
P12 Projector Mounting Guide for Pen- and Non-Interactive Models

6
Printed Monday, December 19, 2016 10:43
AM
6
Diagonal
imagesize
(S)ininch
Imagewidth
(W)inin.
Imageheight
(H)inin.
Distance
fromsurface
of
whiteboard
tocenterof
projector
mount(T)in
in.
Distance
fromsurface
of
whiteboard
tobackof
projector(T1)
inin.
Distance
fromtopof
imagetotop
ofwallplate
(O)inin.
Distance
fromtopof
imagetotop
ofinterface
boss(O1)in
in.
Distance
fromtopof
imagetotop
ofprojector
(O2)inin.
87 75.8 42.6 14.6 9.2 14.3 11.3 10.6
88 76.7 43.1 14.8 9.4 14.4 11.5 10.7
89 77.6 43.6 15.0 9.6 14.6 11.6 10.8
90 78.4 44.1 15.2 9.8 14.6 11.7 10.9
91 79.3 44.6 15.5 10.1 14.8 11.8 11.0
92 80.2 45.1 15.7 10.3 14.8 11.9 11.1
93 81.1 45.6 15.9 10.5 15.0 12.0 11.2
94 81.9 46.1 16.1 10.7 15.1 12.1 11.3
95 82.8 46.6 16.3 10.9 15.2 12.2 11.4
96 83.7 47.1 16.6 11.2 15.3 12.3 11.5
97 84.5 47.6 16.8 11.4 15.4 12.4 11.6
98 85.4 48.0 17.0 11.6 15.5 12.5 11.7
99 86.3 48.5 17.2 11.8 15.6 12.6 11.8
100 87.2 49.0 17.4 12.0 15.7 12.7 11.9
101 88.0 49.5 17.6 12.2 15.8 12.8 12.0
102 88.9 50.0 17.9 12.5 15.9 12.9 12.1
P121080P(16:9)Wallmountinstallationmeasurementchart-inches
P12 Projector Mounting Guide for Pen- and Non-Interactive Models

7
Printed Monday, December 19, 2016 10:43
AM
7
END
Diagonal
imagesize
(S)ininch
Imagewidth
(W)inin.
Imageheight
(H)inin.
Distance
fromsurface
of
whiteboard
tocenterof
projector
mount(T)in
in.
Distance
fromsurface
of
whiteboard
tobackof
projector(T1)
inin.
Distance
fromtopof
imagetotop
ofwallplate
(O)inin.
Distance
fromtopof
imagetotop
ofinterface
boss(O1)in
in.
Distance
fromtopof
imagetotop
ofprojector
(O2)inin.
120 112.4 42.1 23.8 18.4 18.2 15.2 14.4
121 113.3 42.5 24.0 18.6 18.3 15.3 14.5
122 114.2 42.8 24.3 18.9 18.4 15.4 14.6
123 115.2 43.2 24.5 19.1 18.5 15.5 14.7
124 116.1 43.5 24.7 19.3 18.6 15.6 14.8
125 117.0 43.9 25.0 19.6 18.7 15.7 15.0
126 118.0 44.3 25.2 19.8 18.8 15.8 15.0
127 118.9 44.6 25.4 20.0 18.9 15.9 15.2
128 119.8 44.9 25.7 20.3 19.1 16.1 15.3
129 120.8 45.3 25.9 20.5 19.1 16.1 15.4
130 121.7 45.6 26.1 20.7 19.3 16.3 15.5
131 122.6 46.0 26.4 21.0 19.4 16.4 15.6
132 123.6 46.3 26.6 21.2 19.4 16.5 15.7
133 124.5 46.7 26.9 21.5 19.6 16.6 15.8
134 125.5 47.0 27.1 21.7 19.7 16.7 15.9
135 126.4 47.4 27.3 21.9 19.8 16.8 16.0
136 127.3 47.8 27.6 22.2 19.9 16.9 16.1
137 128.3 48.1 27.8 22.4 20.0 17.0 16.2
138 129.2 48.5 28.0 22.6 20.1 17.1 16.3
139 130.2 48.8 28.3 22.9 20.2 17.2 16.4
140 131.1 49.2 28.5 23.1 20.3 17.3 16.5
P12UWHD(16:6)Wallmountinstallationmeasurementchart-inches
P12 Projector Mounting Guide for Pen- and Non-Interactive Models

1. Template must be printed at 100%.
2. Prior to printing, ensure that Page Scaling
is set to “None” on your print dialog box.
3. Measure the bar below. It must be exactly
3 inches long.
CONFIRM PRINTED PAPER SIZE
1 2 3 IN.0
8
P12 Projector Mounting Guide for Pen- and Non-Interactive Models
Wall Mount P12U and P12W Plate Template

9
P12 Projector Mounting Guide for Pen- and Non-Interactive Models
Caution
1. To ensure safety, please read this manual carefully before installation and follow the instructions herein. Store
this manual in a secure place for future reference.
2. The manufacturer shall not be responsible legally for any equipment damage or personal injury caused by
incorrect installation or operation not covered in this manual.
3. The wall mount is designed for easy installation and removal. The manufacturer shall not be liable for damage
to equipment or personnel injuries arising out of human factors or acts of God.
4. The projector hanger must be installed by professional personnel.
5. At least two persons are needed to install or remove the product in order to avoid any hazard caused by
falling objects.
6. Remember to maintain ample space around the projector to ensure suitable ventilation.
7. To ensure safety and avoid any accident, it is necessary to investigate the structure of the ceiling and select
an appropriate, durable location before installation.
8. The ceiling should have load-carrying capability to sustain more than four times the total weight of the
projector and the hanger. Also, make sure it has enough strength to withstand earthquakes and other
shocks.
9. Please carefully check the areas around where the hanger is to be installed:
• Avoid any places that have high temperatures, humidity, or are subject to contact with water.
• Do not install the product near air conditioning vents and avoid places where it is dusty or fumy.
• Only install on vertical walls and avoid slanted surfaces.
• Do not install in places subject to vibrations or shocks.
• Do not install in places subject to direct exposure to bright light, as it may cause eye fatigue when
viewing the display panel.
10. Do not modify any accessory or use broken parts. Contact local distributors if you have any questions.
11. Tighten all screws (do not exert force on any screw with excess torque to avoid breaking the screw or
damaging its thread).
12. The maximum weight of the projector that the hanger can support is below 15kg (33lbs).
13. Do not hang any other objects except the projector on this hanger. Hanging on this hanger by any personnel
is strictly prohibited.
14. Drill holes and screws will be left on the wall once the projector and hanger are removed. Stains may occur
after extended use.
15. Since the manufacturer has no way to control the wall type and installation of wall mount, the warranty of the
product shall only cover the body of the wall mount. The warranty period of the product is 5 years.
16. Please consult the English language manual for any dispute on conditions.