InFocus LitePro 560 User manual

USER'S GUIDE
LCD PROJECTOR

Connecting the LitePro is summarized on the back of this
card and described in detail in the LitePro 560/570 User’s
Guide.
The User’s Guide contains instructions and illustrations for
connections to all compatible computers. It also describes
the remote control buttons and menu functions.
fold and tear here fold and tear here
R
QK-START.FRA Page 1 Tuesday, January 28, 1997 9:18 AM

You must install theprojection bulbs
the first time you use the LitePro.
Refer to the “Read Me First” card
or page 40 of the User’s Guide for
instructions.
Place the LitePro on a flat surface
within six feet of your power
source and your computer.
Remove the lens cover.
Plug in the LitePro’s power cord.
Make sure your computer and
monitor are turned off.
Plug the “LCD” end of the LitePro
cable into the “COMPUTER” con-
nector on the side of the LitePro.
If your computer is a Macintosh,
attach the Mac adapters before
doing step 8. Attach one adapter to
the “VGA”end of theLiteProcable.
Attach the other adapter to the
“MONITOR” end of the LitePro
cable.
Locate your computer’s monitor
cable. Unplug it at the computer
end, leaving the monitor end
attached.
1
2
3
4
5
6
7
Connect the LitePro cable to the
monitor connector on your com-
puter.
If you want to display your presen-
tation on your computer’s monitor
as well as on the projection screen,
attach the “MONITOR” end of the
LitePro cable to the end of the
monitor’s cable.
LP570 only: If you want to connect
your computer’s sound board, a
video player, a speaker system, a
microphone,or a second computer,
refer to the instructions in User’s
Guide.
If you attached your monitor in
Step 8, turn on the monitor.
Press the “|” side of the power
switch to power up the LitePro.
The test pattern will be projected
onto the screen. If necessary, adjust
the height of the LitePro and focus
the lens.
Turn on your computer. The com-
puter image will be projected onto
the screen.
8
9
10
11
12
R
If your computer is... You’ll need...
IBM-compatible desktop or laptop no adapters
Apple Macintosh or PowerBook 2 Mac
adapters
Macintosh PowerBook 1 Mac adapter
and your
video-out cable
QK-START.FRA Page 2 Tuesday, January 28, 1997 9:18 AM

Copyright © 1995 by In Focus Systems, Inc.
Wilsonville, Oregon. All rights reserved.
COPY-FCC.FRA Page 1 Tuesday, January 28, 1997 9:27 AM

Certifications
UL 1950, CSA 950, EN 55022, EN 50082-1, EN 60950
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
Instructions to User
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions in this manual, may cause harmful interference to radio
and television reception. Operation of this equipment in a residential area is likely to cause harmful
interference. If this equipment does cause interference to radio or television reception, the user is
required to correct the interference at his/her own expense. The user may try to correct the
interference by one or more of the following measures:
• Reorient the receiving antenna for the radio or television.
• Relocate the equipment with respect to the receiver.
• Plug the equipment into a different outlet so the equipment and receiver are on different branch
circuits.
• Fasten cables using mounting screws to ensure adequate electromagnetic interference controls.
EN 55022 Warning
This product is intended for use in a commercial, industrial, or educational environment. It is not
intended for residential use.
This is a Class A product. In a domestic environment it may cause radio interference, in which case
the user may be required to take adequate measures. The typical use is in a conference room,
meeting room or auditorium.
Wenn das Produkt Lite Pro 560/570 in Deutschland verkauft wird, muss es Umwelt geschuetzt sein.
(Klasse B) Dieses Product muss mit dem Bundesamt fuer Post und Telekommunikation registriert
sein. (BAPT)
Trademarks
All trademarks are the property of their respective owners and are used in this publication for
identification purposes only.
The following are trademarks or registered trademarks of their respective companies:
• IBM and PS/2: International Business Machines, Inc.
• Apple, Macintosh, Mac II,LC, PowerBook, Quadra, Performa, and Power Mac: Apple Computer
Corp.
• LitePro, LiteShow, and IN FOCUS SYSTEMS: In Focus Systems, Inc.
COPY-FCC.FRA Page 2 Tuesday, January 28, 1997 9:27 AM

Declaration of Conformity
We, In Focus Systems, Inc., 27700B SW Parkway Ave. Wilsonville, Oregon 97070 USA, declare
under our sole responsibility that the:
LitePro 560 and LitePro 560LS LCD projector
LitePro 570 and LitePro 570LS LCD projector
to which this declaration relates, are in conformity with the following standards:
EN 55022. . . . . . . . . . . . . . . . . . .Information Technology Equipment Emission Standard
EN 50082-1 . . . . . . . . . . . . . . . . .Generic Immunity Standard
EN 60950: 1992+A1+A2: 1993 .Safety of Information Technology Equipment
following the provisions of the following directives:
EMC Directive 89/336/EEC, Amended by 93/68/EEC
Low Voltage Directive 72/23/EEC, Amended by 93/68/EEC
European Office
Planetenweg 91, 2132 HL Hoofddorp, The Netherlands
September, 1995
COPY-FCC.FRA Page 3 Tuesday, January 28, 1997 9:27 AM

LitePro 560/570 User’s Guide i
Contents
Safety Summary iii
Introduction 1
Compatibility 2
Cables and Adapters 2
Remote Control Programmer Kit 3
Usage Guidelines 3
If You Need Assistance 3
Setting Up the LitePro 5
Using the LitePro 17
Basic Image Adjustment 17
Turning the LitePro Off 17
Using the Remote Control 17
Focusing the Image 18
Adjusting the Height 18
Switching to the Spare Lamp 19
Using the Remote Control Buttons 20
Using the Menus 24
Menu 1 Functions 26
Menu 2 Functions 28
Audio Menu Functions 36
Maintenance 39
Cleaning the Lens 39
Replacing the Projection Lamps 40
Replacing Batteries in the Remote Control 42
Replacing the Fuse 43
Troubleshooting 47
Before You Call for Assistance 47
Solutions to Common Problems 48
Appendix 51
Specifications 51
Accessories 53
Cable Connector Pin Assignments 54
Laptop Display Activation Chart 56
Index 59
0060-05.TOC Page i Tuesday, January 28, 1997 9:28 AM

LitePro 560/570 User’s Guide iii
Safety Summary
Please read these instructions before using your LitePro projector.
Failure to comply with these instructions could result in fire,
electrical shock, personal injury or equipment damage.
These graphics are used throughout this manual to draw your atten-
tion to important information about the LitePro:
Information that may be unusual or unexpected.
Information that helps you avoid damage to your
equipment.
Information that helps you avoid personal injury.
These graphics are used on the LitePro:
Attention - Refer to the User’s Guide for important
safety information.
Fuse - Refer to “Replacing the Fuse” on page 43 of
this User’s Guide for important safety information.
Hot Surface - Do not touch untilthe LitePro has
cooled.
Do not look into the lens!
Be very careful not to look into the projection lens when the projector
is turned on. The bright light may harm your eyes. Be especially
careful to keep children from looking into the lens.
Power Source
Use only a three-wire grounding type power source. The power
source should not exceed 250 volts rms between the supply
conductors or between either conductor and the ground.
Power Cord
Use only the power cord that was shipped with the LitePro.
Although other power cords might be similar in appearance, they
!
SAFETY.FRA Page iii Tuesday, January 28, 1997 9:29 AM

Safety Summary
iv LitePro 560/570 User’s Guide
have not been safety-tested with the LitePro. Never use a power cord
if it has become damaged or frayed. Contact your In Focus dealer or
call In Focus if you need to replace your LitePro power cord.
Grounding
The LitePro is grounded through the grounding conductor on the
power cord. To avoid electric shock, plug the power cord into a
properly wired receptacle. Do not defeat the purpose of the
grounding-type plug.
Fuse
For protection against the risk of fire, use only a fuse of the specified
type. Refer to page 51 for more information about fuse specifications
and to page 43 for instructions on replacing the fuse.
Lamp
To avoid overheating and unacceptable image quality, replace the
projection lamp with a lamp of the specified type. Refer to page 51 for
lamp specifications and to page 40 for instructions on replacing the
lamps.
Hot Surfaces
The rear of the LitePro becomes very hot during operation. Avoid
touching the exhaust grill on the lamp door. Allow the LitePro to
cools for at least 20 minutes before replacing a lamp. When you open
the lamp door, be very careful not to touch the hot surfaces inside.
Ventilation and Overheating
Openings in the LitePro case provide ventilation to protect it from
overheating. Keep loose papers and other objects well away from the
sides and back of the LitePro. Never operate the LitePro when the
lamp door is open; this disrupts the cooling air flow inside and can
cause the LitePro to overheat. Do not place the LitePro on top of or
close to the computer or other heat-producing equipment.
Liquid Spills
Do not set drinks on top of the LitePro. Spilled liquids canflow inside
and damage the LitePro.
Do Not Disassemble
The only user-serviceable parts on the LitePro are inside the lamp
door at the rear. Do not open any other part of the LitePro. Opening
the LitePro case will expose you to electric shock hazard. All service
must be performed by an authorized In Focus service center.
SAFETY.FRA Page iv Tuesday, January 28, 1997 9:29 AM

LitePro 560/570 User’s Guide 1
Introduction
The In Focus Systems LitePro 560 and 570 LCD projectors provide
640x480 resolution with compatibility up to 800x600. The LitePro’s
active matrix liquid crystal display (LCD) is based on Thin Film
Transistor (TFT™) technology. It can display up to 16.7 million colors.
The LitePro is ideal for high-performance business, CAD and
imaging applications that demand high resolution and exceptional
color quality.
Figure 1. Shipping Box Contents
1. LitePro 560/570 LCD projector not shown:
2. power cord 2 Fuses, 2 Projection Lamps,
3. audio/video cable Soft Carrying Case, Lens
4. Macintosh adapters (2) Cover, Read Me First card,
5. LiteShow diskettes (LP 560LS & LP 570LS) LiteShow User’s Guide (LP
6. LitePro cable 560LS & LP 570LS), Remote
7. remote control units (2) Control Programmer Kit
8. LitePro 560/570 User’s Guide
INTRO.FRA Page 1 Tuesday, January 28, 1997 9:30 AM