B+B SmartWorx UR5i v2 Libratum Guide

Start Guide
for v2 Routers

Start Guide
Safety Instructions
Please take care to following instructions:
•Use the router in compliance with national and international law and in compliance with
any special or additional restrictions regulating use of the router in the various applica-
tions and environments.
•To avoid possible injury and/or damage to the device, observe the relevant provisions
and standards. Use only the original accessories as recommended. Unauthorized de-
vice or accessory modification, or using accessories that have not been approved can
result in router damage and/or violation of the regulations.
•Unauthorized device or accessory modification or using the accessories that have not
been approved can result in warranty termination.
•Do not open the router.
•Caution! The SIM card can be swallowed by small children.
•When connecting the device to a power supply do not exceed the defined voltage.
•Do not expose the router to extreme ambient conditions. Protect the router against dust,
moisture, and high temperature.
•It is recommended that you do not use the router at petrol filling stations. We recommend
observing local restrictions concerning the use of radio-based devices while working with
explosive material for example, at petrol filling stations, or in chemical plants.
•While using the router close to personal medical devices, such as cardiac pacemakers
or hearing aids, proceed with heightened caution.
•Operating the router too close to TV sets, radio receivers, personal computers, or tele-
phones can cause interference.
•It is recommended that you create a copy or backup of the important settings stored in
the memory of the router.
QSG-0001-EN, June 1, 2017 1Released in the Czech Republic

Start Guide
Product Disposal Instructions
The WEEE (Waste Electrical and Electronic Equipment: 2012/19/EU) direc-
tive has been introduced to ensure that electrical/electronic products are recy-
cled using the best available recovery techniques to minimize the impact on
the environment. This product contains high quality materials and components
which can be recycled. At the end of its life this product MUST NOT be mixed
with other commercial waste for disposal. Check with the terms and conditions
of your supplier for disposal information.
Open Source Software License
The software in this device uses various pieces of open source software governed by
following licenses:
•GPL versions 2 and 3
•LGPL version 2
•BSD-style licences
•MIT-style licences
The list of components together with complete license texts can be found on the device
itself. See Licenses link at the bottom of the router’s main Web page (General Status) or point
your browser to this address (replace the DEVICE_IP string with real router’s IP address):
http://DEVICE_IP/licenses.cgi
This is a written offer valid for 3 years since the device purchase offering any third party for
a charge no more than cost of physically performing source distribution, a complete machine-
readable copy of the corresponding source code on a flash drive medium. If you are interested
in obtaining the source, please contact us at:
[e-mail]
Modifications and debugging of LGPL-linked executables:
The manufacturer of the device hereby grants the right to use debugging techniques (e.g.
decompilation) and making customer modifications of any executable linked with a LGPL li-
brary for own purposes. Note these rights are limited to the customer’s own usage. No further
distribution of such modified executables and no transmission of the information obtained dur-
ing these actions may be done.
QSG-0001-EN, June 1, 2017 2Released in the Czech Republic

Start Guide
First Use
Before applying power to the router, connect the components that you required for your
applications. You cannot operate the router without connected antenna, inserted SIM card,
nor connected power supply.
If you do not have connected main antenna during operation of the router, the router can
be damaged!
XR5i v2 routers are not equipped with a cellular module which means that SIM card
readers and antenna connectors are not available on the router.
1. Antenna
Use a SMA connector to connect the antennas to the router. The main antenna is con-
nected to the router by screwing on the ANT connector (see Figure below). The second diver-
sity antenna can also be connected to the DIV connector to improve performance.
QSG-0001-EN, June 1, 2017 3Released in the Czech Republic

Start Guide
2. SIM Card
The SIM card reader, for 3 V and 1.8 V SIM cards, is located on the front panel of the
router. Full version of the router contains two readers. If you intend to use this device to com-
municate over a cellular network, please place an activated data-provisioned SIM card with an
unblocked PIN into the SIM card reader. Insert your SIM card into the SIM1 or SIM2 holder
and push it to the reader (see Figure below).
Before handling of the SIM card disconnect the router from power supply!
3. Power
The router requires an external DC power supply. The DC voltage required is between
+10 to +30 V DC. The router has built-in protection against reverse polarity without signaling.
Connect the power supply cable to the PWR connector on the front panel of the router (see
Figure below) and tighten locking screws.
QSG-0001-EN, June 1, 2017 4Released in the Czech Republic

Start Guide
4. Ethernet
An Ethernet cable may be connected to the ETH connector on the front panel (see Figure
above). By default, this Ethernet port is configured as follows:
Connector Purpose Default Setting
ETH LAN port (default)
Connect your laptop or PC to this port to
get a local web-server for device configu-
ration and diagnostics.
DHCP Server
IP Address: 192.168.1.1
NetMask: 255.255.255.0
If the router is equipped with any expansion port, connect the appropriate cable to the port
PORT1 or PORT2. The pin assignments for expansion ports is described in manual for corre-
sponding expansion port.
Configuration
1. Configuring the Device Using the Web Browser
You can access the router for status monitoring, configuration, and administration after en-
tering the IP address of the router into the web interface. The default IP address is 192.168.1.1
(netmask 255.255.255.0). Configuration access is allowed for the user "root" with the initial
password "root". For a detailed description and examples of the router configurations, see the
Configuration Manual.
2. Configuring the Device Using the Telnet
You can access the router for status monitoring, configuration, and administration using
the Telnet interface (for example Putty client). The default IP address is 192.168.1.1 (netmask
255.255.255.0). Configuration access is allowed for the user "root" with the initial password
"root". For a detailed description and examples of the router configurations, see the Configu-
ration Manual.
QSG-0001-EN, June 1, 2017 5Released in the Czech Republic

Start Guide
3. Configuration Settings via SmartWorx Hub
If your router has been pre-installed with the SmartWorx Hub client, you may configure it
from SmartWorx Hub. Navigate your browser to:
https://hub.bb-smartworx.com
If this is your first time, please register with the site. If not, please login with your username
and password. Once logged in, further assistance can be found here:
https://hub.bb-smartworx.com/Login/Help?HelpFile=bbdms_help.pdf
4. Restoring and Backing up the Router Configuration
After you reset the router, the current configuration is overwritten by the default settings.
We recommend that you back up the router configuration before resetting the device. Refer to
the Configuration Manual for more information.
When the PWR LED starts blinking, it is possible to restore the default configuration of the
router by pressing the RST button on the front panel. After pressing this button, the default
configuration is restored and then the router reboots (green LED will be on).
After logging on to the device for the first time, we strongly recommend to change
the default password due to security reasons. Simultaneously, you will gain ac-
cess to all functions of the router.
Documentation
User’s Manual, Configuration Manual and manual for each expansion port can be found
and downloaded on this web site: www.advantech-bb.cz/download
Hereby, Advantech B+B SmartWorx s.r.o. declares that the radio equipment type
ER75i v2,LR77 v2,LR77 v2 Libratum,RR75i v2,UR5i v2,UR5i v2 Libratum,
XR5i v2 (versions with radio interface only) and XR5i v2E (versions with radio inter-
face only) is in compliance with Directive 2014/53/EU.
XR5i v2 and XR5i v2E versions without radio interface are in compliance with the essential
requirements and other relevant provisions of Directives 2014/30/EU and 2014/35/EU.
The full text of the EU Declaration of Conformity is available at the following internet address:
www.advantech-bb.cz/eudoc
QSG-0001-EN, June 1, 2017 6Released in the Czech Republic