B+B SmartWorx CR10 v2 Guide

START GUIDE
1
Start Guide
Safety Instruction
Please take care to following instructions:
The router must be used in compliance with international and national law and in com-
pliance with any special or additional restrictions regulating using of the Conel router in
different applications and environment.
To avoid possible health injury or/and damage to appliance or/and not-respecting relevant
provisions and standards, using only the original accessories is recommended. Unauthor-
ized device or accessories modification or using accessories that have not been approved
may result in router damage or/and in violating of regulations. Unauthorized device or
accessories modification or using accessories that have not been approved may result in
warranty termination.
The router must not be opened.
Caution! The SIM card could be swallowed by small children.
Voltage at the power connector of the router must not be exceeded.
Do not expose the router to extreme ambient conditions. Protect the router against dust,
moisture, and high temperature.
It is recommended not to use the router at petrol stations. We remind observing locale
restrictions concerning using radio-based devices for example at petrol stations, in
chemical plants, while working with explosives etc.
Switch off the router while travelling by plane. Router operation aboard airplane may
affect or interfere the mobile network and might be unlawful. Not respecting airplane
staff instructions may result in suspension or total cancellation of telephone services for
the respective client or/and may result in legal sanctions.
While using the router close to personal medical devices, such as cardiac pacemakers or
hearing aids, you must proceed with heightened caution.
Operating router too close to TV sets, radio receivers and personal computers, the
telephones etc. may cause interference.
It is recommended to create copy or backup of all the important settings stored in mem-
ory of router.
Product Disposal Instructions
The WEEE (Waste Electrical and Electronic Equipment: 2002/96/EC) directive has been
introduced to ensure that electrical/electronic products are recycled using the best available
recovery techniques to minimize the impact on the environment. This product contains high
quality materials and components which can be recycled. At the end of its life this product
MUST NOT be mixed with other commercial waste for disposal. Check with the terms and
conditions of your supplier for disposal information.

START GUIDE
2
First Use
It is necessary to connect all the components that are required to run your applications
before putting the router into operation.
The router cannot be operated without connected antenna, inserted SIM card and con-
nected power supply. If there is no connected antenna during operation of the router, the
router may be damaged!
XR5i v2 router is not equipped with a 2G/3G/4G module which means that SIM card
holders and antenna connectors (except for WiFi antenna connector) are not available on
the router.
1. Antenna Connection
Use SMA connector for antenna connection. Main antenna is connected by screwing at
ANT connector (see figure below).
2. Inserting SIM Card
The SIM card reader for 3 V and 1.8 V SIM cards is located at the front panel of Conel
router. To initiate router operation it is necessary to insert an activated SIM card with
unblocked PIN to the SIM card reader.
Slide out SIM card holder by pressing the small yellow button right from the SIM card
socket. Insert SIM card into holder and push the holder into the reader (see figure below).
Antenna
cable
SIM card
holder

START GUIDE
3
3. Power Cable Connection
The router requires DC power supply from +10 to +30 V DC. The router has a built-in
protection against reverse polarity without signaling.
Connect power cable to the connector labeled as PWR on the front panel of the router
and tighten locking screws (see figure below).
4. Ethernet Cable ConnectionS
Ethernet cable has to be connected to ETH connector on the front panel (see figure
below). Ethernet cable is used for configuration and communication with the router.
If expansion ports are assembled, cable is connected to port PORT1 or PORT2. Wiring
of pins for expansion ports are described in manual of corresponding expansion port. These
manuals can be found on the Conel website: http://www.conel.com/download. Please, use
the following login information:
Username: ConelFreeDownload
Password: coneldownload
Power
cable
Ethernet
cable

START GUIDE
4
Configuration Settings over Web Browser
Status monitoring, configuration and administration of the router can be done using
web interface which is available after inserting IP address of the router to your web browser.
Default IP address is 192.168.1.1. Configuration is allowed for user "root" with initial pass-
word "root".
Detailed description of the router configuration via router web interface can be found
in Configuration manual, see Conel website: http://www.conel.com/download. Please, use
the following login information:
Username: ConelFreeDownload
Password: coneldownload
Configuration Settings over Telnet
Status monitoring, configuration and administration of the router can be done using
Telnet interface which is available after inserting IP address of the router to Telnet interface.
Default IP address is 192.168.1.1. Configuration is allowed for user "root" with initial pass-
word "root".
Detailed description of the router configuration via router web interface can be found
in Configuration manual, see Conel website: http://www.conel.com/download. Please, use
the following login information:
Username: ConelFreeDownload
Password: coneldownload
Restoring and Backup of the Router Configuration
The moment PWR LED starts blinking it is possible to restore initial settings of router by
pressing RST button on the front panel. After pressing this button configuration is restored
and reset is done shortly afterwards (green LED will be on).
We recommend backup router configuration (see Configuration manual) before reset
because after router reset is current configuration overwritten by default one.
After the first login we strongly recommend to change default password due to
security reasons. Simultaneously, you will gain access to all functions of the router.
Documentation
User manual, Configuration manual and manuals for each expansion port can be found
on the Conel company website: http://www.conel.com/download. Please, use the following
login information:
Username: ConelFreeDownload
Password: coneldownload
Conel declares that the Bivias v2, CR10 v2, ER75i v2, LR77 v2, LR77 v2 Libratum, UCR11
v2, UR5i v2, UR5i v2 Libratum, XR5i v2 and XR5i v2E are in compliance with the essential
requirements and other relevant provisions of direction 1995/5/ES.
Declaration of conformity was issued and it is possible to get it on Conel company website
(www.conel.com) or from technical support of this company.