B+B SmartWorx UHR207 User manual

Recommended Accessories
External Class 2
Power Supply
Model# PS12VLB-INT-MED
Documentation Number: 710-10915-00_r1_UHRx07_2218qsg
1 [phone] | Europe: [phone]
advantech-bb.com
707 Dayton [phone] | Fax: [phone]
www.advantech-bb.com | E-mail: [e-mail]
Before you begin, be
sure you have the following:
Model UHR207 or UHR307
Non-Isolated Isolated
Industrial 7-Port USB Hub
Fast and easy on the web: www.advantech-bb.com
+ 7 Port Industrial USB Hub
+ USB Cable
+ Panel Mount Adapters
+ DIN Rail Adapters
+ Power Supply (optional, not included)
QUICK START
GUIDE
UL Information
SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS
A, B, C AND D HAZARDOUS LOCATIONS, OR
NONHAZARDOUS LOCATIONS ONLY.
WARNING - EXPLOSION HAZARD - SUBSTITUTION OF
ANY COMPONENT MAY IMPAIR SUITABILITY FOR CLASS
I, DIVISION 2.
WARNING - EXPLOSION HZARD - DO NOT DISCONNECT
EQUIPMENT WHILE THE CIRCUIT IS LIVE OR UNLESS
THE AREA IS KNOW TO BE FREE OF IGNITABLE
CONCENTRATIONS.”
INSTALL IN ACCORDANCE WITH CONTROL DRAWING
NUMBER 9340R0.
THE UNIT IS TO BE CONNECTED TO A CLASS 2 POWER
SOURCE VIA THE TERMINAL BLOCK OR BARREL
CONNECTOR. POWER CANNOT BE APPLIED TO BOTH
CONNECTORS AT THE SAME TIME.
FIELD WIRING CONDUCTOR MINIMUM INSULATION
RATING 80 °C.
Informations UL
ADAPTÉ POUR UTILISATION EN CLASSE I, DIVISION 2,
GROUPES A, LIEUX DANGEREUX B, C ET D, OU
EMPLACEMENTS NON DANGEREUX SEULEMENT.
AVERTISSEMENT - RISQUE D’EXPLOSION -
SUBSTITUTION DE TOUT COMPOSANT PEUT NUIRE
CONFORMITÉ À CLASS I, DIVISION 2.
AVERTISSEMENT - RISQUE D’EXPLOSION - NE PAS
DÉBRANCHER EQUIPEMENT LORSQUE LE CIRCUIT EST
EN DIRECT OU SAUF LA ZONE EST SAVOIR ETRE LIBRE
DE INFLAMMABLES CONCENTRATION.
INSTALLER CONFORMÉMENT AU CONTRÔLE DE
DESSIN NUMÉRO 9340R0.
L’UNITÉ DOIT ÊTRE CONNECTÉE À UNE SOURCE
D’ALIMENTATION DE CLASSE 2 VIA LE BORNIER OU LE
CONNECTEUR CYLINDRIQUE. LA PUISSANCE NE PEUT
PAS ÊTRE APPLIQUÉE AUX DEUX CONNECTEURS EN
MÊME TEMPS.
LE CONDUCTEUR DE CÂBLAGE DE TERRAIN DOIT
AVOIR UNE ISOLATION THERMIQUE MINIMALE DE 80 °C.
UL
6

Product Overview
Mounting
1
DIN Rail Mounting
Attach the DIN rail bracket
with the at surface of the
bracket facing the back
of the hub.
Panel Mounting
The panel mount brackets
can be attached to the sides
of the hub. They can be
attached in (4) positions:
Up, Down, Forward,
Backward
Connect Power Supply
LED Status
Grounding
2
4
3
External Power
The non-isolated Model# UHR207 and the isolated Model#
UHR307 will not operate without an external power supply.
You can use the detachable terminal block input or the locking
barrel jack. Terminal block is polarity protected.
When externally powered, Models UHR207 and UHR307
provide 5VDC at 500 mA to each downstream port. They
require 10 to 30 VDC external power and will consume a
maximum of 16 W.
B+B SmartWorx strongly recommends that you ground the
chassis. Connect a grounding wire from the green ground lug
to a good source of earth ground.
LED Type State Description
External
Power
ON Power is present. Hub will supply 5VDC at
500 mA per downstream port.
OFF No power is present.
Port LEDs
ON Port is Active and ready for use.
OFF Port has a Fault. Power may need to be
cycled.
To USB
Host
Front View
LED
Indicators
Downstream
Ports
Side View
Detachable
Terminal Block
Barrel Plug
Model# UHR207 hub is installed,
but a downstream device does
not seem to be working.
Some USB devices get their power from the USB cable. If
you are using Model# UHR207 without an external power
supply, it will only provide 100 mA to the downstream ports.
If your devices need more power, connect an external power
supply to Model# UHR207. It will then provide 500 mA to the
downstream ports.
Do I need drivers for a USB hub?
No, the operating system will detect it and install it
automatically.
How can I be sure it has been installed?
The new hub will be listed in your Device Manager.
Can I use USB 1.1 and USB 2.0
devices together?
Yes. USB 2.0 is backwards compatible with USB 1.0
and USB 1.1.
What is the difference between Model#
UHR207 and Model# UHR307?
Both hubs are ruggedized for tough industrial applications.
Model# UHR307 additionally provides 4 kV isolation.
Troubleshooting
5