Bradford White 705-B User manual

Features:
Bradford White is ISO registered to the
9001 standard.
■1" Non-CFC foam insulation—surrounds the tank surface, saving
energy by retarding loss of heat.
■Closed combustion—all air for combustion is taken directly from the
outside. The co-axial vent pipe (pipe inside a pipe) draws combustion
air in through the outer pipe (6"), and exhausts the products of
combustion through the inner pipe (4").
■Co-axial—rotational venting at top of unit.
■No electrical power necessary.
■Piezo igniter—for ease of lighting the pilot.
■Water Connections—3/4" NPT factory installed true dielectric fittings.
Extends water heater life and eases installation.
■Vitraglas®lined tank—Bradford White water heater tanks are
protected from the corrosive effects of hot water by an exclusive
ceramic porcelain-like coating. The Bradford White high silica Vitraglas®
lining provides a tough interior surface for our water heater tanks.
■Factory installed Hydrojet®Total Performance System—cold inlet
sediment reducing device. Helps prevent sediment build up in tank.
Increases first hour delivery of hot water while minimizing temperature
build up at top of tank.
■Protective magnesium anode rod—provides added protection
against corrosion for long trouble-free service.
■Brass drain valve.
■T&P relief valve—factory installed.
■Side Tappings—for space heating purposes.
■Fully automatic controls—automatic temperature selection at your
fingertips. Built-in energy cut-off switch prevents abnormally high water
temperature for extra safety. Built-in gas pressure regulation. Fast-
acting thermostat starts heat recovery cycle sooner.
■NSF construction available.
■Optional vent kits—allow for up to 8 foot max vertical and 8 foot max
horizontal (2.4 meters)). All DH models must be terminated horizontally.
■Three year limited warranty on steel tank—heavy gauge steel
automatically formed, rolled and welded to assure a continuous seam
for glass lining.
■One year limited warranty on parts.
■Design certified by CSA International. (formerly AGA and CGA)
MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING U.S. PATENTS: 7,063,133 B2; 5,954,492;
5,954,492; 5,761,379; 5,943,984; 5,081,696; 5,988,117; 6,142,216; 5,199,385; 5,574,822; 5,372,185; 5,485,879;
5,277,171; (B1)5,341,770; 5,660,165; 5,596,952; 5,682,666; 4,904,428; 5,023,031; 5,000,893; 4,669,448;
4,829,983; 4,808,356; 5,115,767; 5,092,519; 5,052,346; 4,416,222; 4,628,184; 4,861,968; 4,672,919; Re.
34,534. OTHER U.S. AND FOREIGN PATENT APPLICATIONS PENDING. CURRENT CANADIAN PATENTS:
1,272,914; 1,280,043; 1,289,832; 2,045,862; 2,112,515; 2,108,186; 2,107,012; 2,092,105.5.
Commercial Gas Light Duty
High Input Direct Vent Water Heater
STANDARD
9001
1

ABCDEFG
Imp. US
Gal. Gal. Input
Cap. Cap. Liters BTU KW in. mm in mm in mm in mm in mm in mm in mm in mm Lbs. kg
DH-50T-50B-3N 40 48 182 50,000 14.7 39 47 178 751⁄41411 20 508 583⁄41492 151⁄4387 521⁄41327 521⁄4 1327 4/6 102/152 197/89.4
DH-65T-55B-3N 54 65 246 55,000 16.1 43 51 193 781⁄41988 22 559 62 1575 151⁄4387 56 1422 56 1422 4/6 102/152 243/110
DH-75T-60B-3N 62 75 284 60,000 17.6 47 56 212 751⁄21918 241⁄2622 59 1499 151⁄4387 52 1321 52 1320 4/6 102/152 281/127
Sample Specification
The water heater shall be a Bradford White model with a rated storage capacity of not less
than _______ gallons (liters), a minimum gas input of _______ BTUH (KWH), and a
minimum recovery of _______ GPH (LPH) at 100°F (56°C) temperature rise. It shall be
design certified by CSA International (formerly AGA and CGA). The tank shall be lined with
Vitraglas®vitreous enamel. The tank shall have one extruded magnesium anode rod. The
heater shall be insulated with Non-CFC foam insulation. This water heater shall be
equipped with an ASME rated T&P relief valve. The entire installation shall be in
compliance with state and local codes and ordinances.
705-B-HIDV-1106-A Printed in U.S.A.
Horizontal Installation Only
The standard vent kit (239-42979-00) is ordered and shipped separately. The components
are as follows: 4" vent tube*, 6" Air Intake Tube, Vent Terminal, Inner Wall Term Mounting
Flange, Outer Wall Term. Mounting Flange, Vent Terminal Hardware, RTV Silicone Sealant,
4"Vent Elbow and a 6" Air Intake Elbow.
PRODUCTS ONLY FOR PROFESSIONALS
Sales/800-523-2931
Fax/215-641-1670
Technical Support/ 800-334-3393
Fax/269-795-1089
Warranty/800-531-2111
Fax/269-795-1089
International:
Telephone/215-641-9400
Telefax/215-641-9750
Ambler, PA
888-538-7833
Fax on Demand:
bradfordwhite.comwww.
For U.S. and Canada field service,
contact your professional installer or
local Bradford White sales representative.
Sales/Technical Support
866-690-0961
905-238-0100
Fax/905-238-0105
Mississauga, ON
www. bradfordwhitecanada.com
Energy Saver Direct Vent Models
NATURAL GAS
All propane gas heaters are equipped with Cast Iron Burner. Change suffix “BN”
to “CX”.
Suitable for Water (Potable) Heating and Space Heating
Toxic chemicals, such as those used for boiler treatment, shall NEVER be introduced
into this system. This unit may NEVER be connected to any existing heating system
or component(s) previously used with a non-potable water heating appliance.
General
All gas water heaters are certified at 300 PSI (2068 kPa) test pressure and 150 PSI
(1034 kPa) working pressure. All water connections are 3⁄4"(19mm) NPT on
8" (703mm) centers on top of unit, all gas connections 1⁄2"(13mm). All models design
certified by CSA International (formerly AGA and CGA). Recovery based on rated
efficiency.
Meets NAECA requirements. All natural gas models meet SCAQMD
requirements.
Dimensions and specifications subject to change without notice in accordance
with our policy of continuous product improvement.
Vitraglas®and Hydrojet®are registered trademarks of Bradford White®Corporation.
©2006, Bradford White Corporation. All rights reserved.
Model
Number Imp.
Gal. US GPH LPH
GPH Rec.
56°C/100°F. Rise
(LP) Propane Gas Inputs Recovery at
50°C Rise and 100°F Rise
Imp. U.S. Liters/
GPH GPH Hr.
DH-50T-50-3CX 48,000 BTU/H 14.1 KW 38 45 170
DH-75T-60-3CX 57,000 BTU/H 16.7 KW 44 53 200
Ht. to
Center
Line of
Vent Jacket
Dia.
Ht. to
Top of
Heater
Ht. to
Gas
Conn.
Vent
Dia.
Approx.
Shipping
Weight
Ht. to
T&P
Conn.
Space
Htg.
Outlet
Space
Htg.
Inlet
153⁄4400
153⁄4400
161⁄2419
*(2) = Order two of the kits referenced.
*(3) = Order three of the kits referenced.
The bold text above show what kit(s) are needed in addition to the standard vent and air
intake tubes. If the standard vent and air intake tubes are not used in the venting system
(those that do not have bold text) they can be discarded or saved.
For vent distances not found in the selection chart above, please contact the Product
Management Department for sizing recommendations.
Horizontal"X"
16 1/4 18 25 1/4 37 3/4 61 5/16
17 3/16 20 11/16 35 3/16 57 7/8 107 5/16
order order no add'l order order
11 9/16 kit F kit G kit req'd kit H kit I
16 5/16 *orderorder order order order
171/4 kit F (2) kit G & F kit F kit H & F kit F & I
18 1/16 order order order order order
203/4 kit F & G kit G (2) kit G kit G & H kit G & I
25 5/16order order order order order
35 1/4 kit F kit G kit H kit H (2) kit I
38 1/16order order order order order
57 15/16 kit H & F kit H & G kit H (2) kit H (3) kit H & I
61 3/8 order order order order order
Vertical "Y"
107 3/8 kit I & F kit I & Gkit I kit I & H kit I (2)
Optional Kits:
Part Number Description
243-42516-00 Kit F – Telescopes from 43⁄4"to 511⁄16"
243-42517-00 Kit G – Telescopes from 61⁄2"to 93⁄16"
243-42514-00 Kit H – Telescopes from 133⁄4"to 2311⁄16"
243-42512-00 Kit I – Telescopes from 4913⁄16"to 9513⁄16"
For more details on the vent kits above, please reference the
supplemental venting instructions.
C
E & F
D
1/2” GAS
CONNECTION
SIDE WATER OUTLET
DRAIN VA LV E
SIDE WATER INLET
G
A
B
6.5 inch (16.5 cm)
Min. Diameter Hole in Wall
Y
11 9/16
X
11 1/2
7 3/16”
Boot Extension
H
CEC listed. 78% Recovery Efficiency for all models.