Bradford White E32-120R User manual

238-43984-00B 1/10
Conversion Kit Instructions
For Models: E32-50S, E32-80R, & E32-120R
(To be performed ONLY by qualified service providers)

Instructions for Conversion of Commercial Electric Models
2
NOTICE
The conversion procedure outlined in this manual is to be executed
ONLY by Qualified Service Personnel. Before attempting conversions
it is recommended that you read the detailed instructions described
herein.
The purpose of this instruction manual is to instruct about the changing of wattage, voltage, and electrical
phase for the commercial electric water heaters manufactured by Bradford White Corporation. Underwriters
Laboratories Inc. recognizes this procedure as herein presented and no deviation from these instructions
are allowed.
Special factory prepared “Conversion Kits” must be used for these conversions. There are separate
conversion kits that have individual instructions and MUST be followed. Page 4 of these instructions lists
the kits that have been prepared for the various wattages and voltages.
These instructions do not allow for a modification that adds or deletes the number of heating elements
originally supplied with the heater; therefore such a modification must NOT be attempted.
These conversion kits are only applicable to Models E32-50S / E32-80R / E32-120R.
The following information is provided to assist in the successful conversion of the water heater:
Page
Safety precautions .........................................................................3
Introduction ....................................................................................3
Required materials and tools .........................................................3
Water heater preparation prior to conversion.................................3
Conversion kits...............................................................................4
Conversion of water heater K-W....................................................5
Conversion of water heater operating voltage ...............................6
Conversion of water heater electrical power supply phase............7
Recheck and inspection of the conversion results.........................8
Concluding steps and reassembly after completion.......................9

Instructions for Conversion of Commercial Electric Models
3
Safety Precautions
NOTICE
The conversion procedure outlined in this manual is to be executed
ONLY by Qualified Service Personnel. Before attempting conversions
it is recommended that you read the detailed instructions described
herein.
Be sure to disconnect the water heater from the electrical supply before performing any servicing of the
electrical system or before attempting any of the conversion procedures. Never perform servicing of the
electrical system or any of the conversion procedures with wet hands or when you are in contact with water
that is on the floor or in the vicinity of the water heater.
Introduction
These conversions have been brought into being in order to expedite the water heater replacement activity.
Water heaters suitable for conversion have been wired at the factory to the maximum electrical duty for
which they have been designed. Therefore, internal electrical components are provided that satisfy the
maximum voltage and maximum electrical current conditions
Wattage, voltage, and phase requirements can be readily fitted to the heater. Conversions may involve
altering any one or all of these electrical characteristics.
Required Materials and Tools
•Screw-in element removal wrench --- or --- 1 ½” deep well socket wrench.
•Phillips head screwdriver
•Standard screwdriver
•Conversion Kit that includes: conversion instructions, electrical elements, product label overlay
(related to the newly created electrical parameters), and element gaskets. Refer to page 4 of these
instructions in order to determine the correct Conversion Kit numbers.
Water Heater Preparation
Locate the areas of the carton to be opened opposite the three electrical elements. A dotted line locates
the position on the carton that needs to be scored and cut. Make these three-sided cuts and fold the carton
flap outward to make an opening in the carton. The carton flap will be closed to seal the carton after
conversion is completed. Remove the three element cover screws and the element covers from the water
heater in order to provide access to the elements.
Locate the area of the carton to be opened opposite the electrical enclosure box. A dotted line locates the
position on the carton that needs to be scored and cut. Make this three-sided cut and fold the carton flap
outward to make an opening in the carton. The carton flap will be closed to seal the carton after conversion
is completed.

Instructions for Conversion of Commercial Electric Models
4
Conversion Kits for Models E32-50S-3/80R-3/120R-3
1. Refer to Table 1 below that contains water heater KW, Element Wattage, Voltage, and kit part
numbers.
2. Locate the KW of the required water heater.
3. Move across the table (to the right) until you reach the required voltage.
4. Select the required kit number.
5. Use that kit for this conversion.
6. Refer to the remaining pages for a detailed conversion procedure.
Table 1. Conversion Kit Table
Kit Part NumbersRequired
Total Water
Heater (KW)
Element
Wattage 208 volts 240 volts 480 volts
6 2000 265-43942-13 265-43942-07 265-43942-01
9 3000 265-43942-14 265-43942-08 265-43942-02
12 4000 265-43942-15 265-43942-09 265-43942-03
13.5 4500 265-43942-16 265-43942-10 265-43942-04
15 5000 265-43942-17 265-43942-11 265-43942-05
18 6000 265-43942-18* 265-43942-12 265-43942-06
*265-43942-18 will require control box replacement (included in kit).
These three element water heaters with surface mount thermostats have been factory wired with the
following common components; terminal block for max service wire size of 2 AWG, 3 elements each having
a surface mount thermostat with hi-limit control, two fuse blocks rated at 480 volts ac max, and 6 type G 30
amp fuses (rated at 480 volts max).

Instructions for Conversion of Commercial Electric Models
5
Wattage/Voltage Conversion --- Element Changes
1. Remove and replace one element at a time.
2. Disconnect the electrical wires from the element terminals.
3. Remove the electrical elements using the Screw-in element removal wrench --- or ---- a 1 ½” deep
well socket wrench.
4. Remove the replacement elements from the conversion kit. Check the element markings to ensure
correct wattage and voltage before installing.
5. Apply the new gasket (provided in the kit) to the element. Make sure the gasket is aligned correctly
and it is not rolled-over.
6. Thread the replacement element into the element fitting until it is seated. Tighten ½ to ¾ turns with
the element wrench.
7. Re-connect the wiring to the element terminals. The screw should be snuggly tightened but caution
should be exercised not to over tighten. Over tightening could fracture the element ceramic terminal
block, and would require replacement.
8. Repeat this procedure (steps 1 thru 7 above) for all other elements needing replacement.
Figure 1. Example of element removal/installation.
Element Cover
Element Gasket
Element

Instructions for Conversion of Commercial Electric Models
6
Voltage Conversion
1. Voltage conversion is accomplished by replacing the existing elements with elements that are rated
at the required voltage.
2. To accomplish this conversion refer to the above procedure for KW Conversion ---- Element
Changes.
3. Execute steps 1 thru 8 of that procedure.
Control Box Conversion
NOTICE
Control box conversion is ONLY required when converting water heater
to 18Kw 208v (Kit # 265-43942-18).
1. Open front panel of control box installed on water heater and disconnect the (6) load wires from fuse
blocks.
2. Remove (4) screws joining control box to water heater and remove control box.
CAUTION
Use caution to not damage any of the wire insulation when removing
control box.
3. Install new control box onto the water heater by feeding the wires through the back of the control box
and reinstall (4) mounting screws.
4. Reconnect wires to new fuse blocks. Be certain to match wire colors to Line side of fuse blocks.
Figure 2. Example of control box removal/installation.
Control Box
Wire Harness
(Load wires)

Instructions for Conversion of Commercial Electric Models
7
Electrical Phase Conversion
Electrical phase conversion will require a change from single-phase to three-phase or an opposite
conversion change from three-phase to single-phase. Each of these conversions will be explained
separately as follows:
Figure 3.
Example of finished Three Phase construction.
Figure 4.
Example of finished Single Phase construction.
Instructions to convert FROM Three-Phase TO Single-Phase:
(All connections are to be made on the LOAD side of the terminal block)
1. Disconnect blue wire and yellow wire from terminal L-3 of the terminal block.
2. Connect yellow wire to terminal L-1 of the terminal block. The black wires should remain connected
to L-1 of the terminal block as it was originally manufactured.
3. Connect blue wire to terminal L-2 of the terminal block. The red wires should remain connected to
L-2 of the terminal block as it was originally manufactured.
4. Field wiring for the water heater power supply will eventually be connected to the line terminals L-1
and L-2 of the terminal block when the product is installed.
Instructions to convert FROM Single-Phase TO Three-Phase:
(All connections are to be made on the LOAD side of the terminal block)
1. Disconnect yellow wire from terminal L-1 of the terminal block
2. Disconnect blue wire from terminal L-2 of the terminal block
3. Connect both blue and yellow wires to L-3 of the terminal block
4. Field wiring for the water heater power supply will eventually be connected to the line terminals L-1,
L-2, and L-3 of the terminal block when the product is installed.

Instructions for Conversion of Commercial Electric Models
8
Phase Conversion Only kits
Table 2. Phase Conversion Kits.
6KW 9KW 12KW
Volts Conversion
Kit Volts Conversion Kit Volts Conversion Kit
208 265-45246-13 208 265-45246-14 208 265-45246-15
240 265-45246-07 240 265-45246-08 240 265-45246-09
480 265-45246-01 480 265-45246-02 480 265-45246-03
13.5KW 15KW 18KW
Volts Conversion
Kit Volts Conversion Kit Volts Conversion Kit
208 265-45246-16 208 265-45246-17 208 265-45246-18
240 265-45246-10 240 265-45246-11 240 265-45246-12
480 265-45246-04 480 265-45246-05 480 265-45246-06
WARNING
Recheck and inspect to make certain all components involved in the
conversion are correct and secure.
Recheck all of the electrical wiring changes made against the wiring diagram requirements for accuracy.
Check to insure all of the electrical connections are tightly secured and the electrical wire routings are
orderly.
Special attention should be given to the electrical heating elements. The wattage and voltage rating of the
element is marked on the element itself. Confirm the marking agrees with the intended conversion.
Additionally, the element wattage can be verified by checking the electrical resistance (ohms of resistance)
with an Ohm Meter. This should be done initially before connecting the element to the circuit. The element
resistance should be plus or minus 5 percent of the following values:
Table 3. Ohms of Electrical Resistance.
Voltage Rating of the ElementElement
Wattage 208 volts 240 volts 480 volts
2000 21.6 28.8 115.2
3000 14.4 19.2 76.8
4000 10.8 14.4 57.6
4500 9.6 12.8 51.2
5000 8.7 11.5 46.1
6000 7.2 9.6 38.4

Instructions for Conversion of Commercial Electric Models
9
Concluding Steps
The water heater rating plate will need to be
modified because the conversion altered the
electrical characteristics of the water heater. Refer to
Figure 5which displays a typical commercial electric
rating plate that is to be altered. This rating plate is
placed on every Commercial Electric water heater
produced by Bradford White Corporation. Locate
this rating plate on the water heater you have just
converted.
Figure 5. Rating plate example.
Also locate the adhesive backed label (see Figure 6)
that is provided inside the kit. The label will be
marked with the new electrical data that is accurate
for the conversion just executed. The kit will contain
two labels for this voltage and KW, (1) for three
phase and (1) for single phase. Select the correct
label for the electrical phase in this conversion.
Figure 6. Rating plate overlay example.
Remove the adhesive peel strip and place this label
onto the rating plate in such a manner that the new
electrical data will appear in place of the data
originally marked. Refer to
Figure 7to the right that displays the rating plate
revision.
Figure 7. Rating plate with overlay installed.
Replace all insulation pieces and element covers that were removed. Replace the electrical enclosure door.
Heater identification information that was placed on the water heater carton must also be altered. This can
be done by making a bold face inscription on the carton with a large size black ink marker. Write the new
electrical data in place of the original data.

NOTES
10