Bradford White 105-B User manual

Features:
Bradford White is ISO registered to the
9001 standard.
■All residential storage models meet or exceed efficiency requirements
of the Department of Energy. ASHRAE Standard 90.1 b (current
standard) and the National Appliance Energy Conservation Act of 1987
recent amendment effective January 20, 2004 which supercedes all
state and local efficiency requirements.
■1" Non-CFC foam insulation—surrounds the tank surface, saving
energy by retarding loss of heat.
■Closed combustion—all air for combustion is taken directly from the
outside. The co-axial vent pipe (pipe inside a pipe) draws combustion
air in through the outer pipe (6"), and exhausts the products of
combustion through the inner pipe (4").
■Co-axial—rotational venting at top of unit.
■Heat Traps—factory installed, minimizes heat loss through piping.
■Water Connections—3/4" NPT factory installed true dielectric fittings.
Extends water heater life and eases installation.
■No electrical power necessary.
■Piezo igniter—for ease of lighting the pilot.
■Vitraglas®lined tank—Bradford White water heater tanks are
protected from the corrosive effects of hot water by an exclusive
ceramic porcelain-like coating. The Bradford White high silica Vitraglas®
lining provides a tough interior surface for our water heater tanks.
■Factory installed Hydrojet®Total Performance System—cold inlet
sediment reducing device. Helps prevent sediment build up in tank.
Increases first hour delivery of hot water while minimizing temperature
build up at top of tank.
■Protective magnesium anode rod—provides added protection
against corrosion for long trouble-free service.
■Brass drain valve.
■T&P relief valve—included.
■Side Tappings—for space heating purposes.
■Fully automatic controls—automatic temperature selection at your
fingertips. Built-in energy cut-off switch prevents abnormally high water
temperature for extra safety. Built-in gas pressure regulation. Fast-
acting thermostat starts heat recovery cycle sooner.
■Optional vent kits—allow for up to 8 foot max vertical and 8 foot
max horizontal (2.4 meters). All DH-1 models must be terminated
horizontally
■Six or ten year limited warranty on steel tank—heavy gauge steel
automatically formed, rolled and welded to assure a continuous seam
for glass lining.
■Six year limited warranty on parts.
■Design certified by CSA International. (formerly AGA and CGA)
MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING U.S. PATENTS: 7,063,133 B2; 5,954,492;
5,954,492; 5,761,379; 5,943,984; 5,081,696; 5,988,117; 6,142,216; 5,199,385; 5,574,822; 5,372,185; 5,485,879;
5,277,171; (B1)5,341,770; 5,660,165; 5,596,952; 5,682,666; 4,904,428; 5,023,031; 5,000,893; 4,669,448;
4,829,983; 4,808,356; 5,115,767; 5,092,519; 5,052,346; 4,416,222; 4,628,184; 4,861,968; 4,672,919; Re.
34,534. OTHER U.S. AND FOREIGN PATENT APPLICATIONS PENDING. CURRENT CANADIAN PATENTS:
1,272,914; 1,280,043; 1,289,832; 2,045,862; 2,112,515; 2,108,186; 2,107,012; 2,092,105.5.
Residential Energy Saver
High Input Direct Vent Water Heater
STANDARD
9001
1
EFFICIENCY
RATING
CERTIFIED

6-Year Limited Warranty on
Component Parts
BRADFORD WHITE CORPORATION has
a6-year warranty on replaceable parts–
thermostat, burner, dip tube, drain valve
and piezo igniter. These quality
components are manufactured for us by
industry leaders and will be replaced in
the event of failure during the parts
warranty period (exclusive of shipping
and re-installation cost).§
6or 10-Year Limited
Tank Warranties
BRADFORD WHITE CORPORATION
LIMITED WARRANTY: Protects your
investment in a quality glass-lined
heater. If the tank leaks for reasons of
faulty materials, workmanship, or
corrosion within the warranty period, the
heater will be replaced with a compara-
ble heater of our manufacture (exclusive
of shipping and re-installation cost).§
Horizontal Installation Only
Optional Kits:
Part Number Description
243-42516-00 Kit F – Telescopes from 43⁄4"to 511⁄16"
243-42517-00 Kit G – Telescopes from 61⁄2"to 93⁄16"
243-42514-00 Kit H – Telescopes from 133⁄4"to 2311⁄16"
243-42512-00 Kit I – Telescopes from 4913⁄16"to 9513⁄16"
*(2) = Order two of the kits referenced.
*(3) = Order three of the kits referenced.
The bold text above show what kit(s) are needed in addition to the standard vent and air
intake tubes. If the standard vent and air intake tubes are not used in the venting system
(those that do not have bold text) they can be discarded or saved.
For vent distances not found in the selection chart above, please contact the Product
Management Department for sizing recommendations.
Sales/800-523-2931
Fax/215-641-1670
Technical Support/ 800-334-3393
Fax/269-795-1089
Warranty/800-531-2111
Fax/269-795-1089
International:
Telephone/215-641-9400
Telefax/215-641-9750
Ambler, PA
888-538-7833
Fax on Demand:
bradfordwhite.comwww.
For U.S. and Canada field service,
contact your professional installer or
local Bradford White sales representative.
Sales/Technical Support
866-690-0961
905-238-0100
Fax/905-238-0105
Mississauga, ON
www. bradfordwhitecanada.com
Energy Saver Direct Vent Models CEC listed. 78% Recovery Efficiency for all models.
For 10 year models, change suffix from “6” to “10”.
All propane gas heaters are equipped with Cast Iron Burner.
Change suffix “BN” to “CX”.
Suitable for Water (Potable) Heating and Space Heating
Toxic chemicals, such as those used for boiler treatment, shall NEVER be introduced
into this system. This unit may NEVER be connected to any existing heating system or
component(s) previously used with a non-potable water heating appliance.
General
All gas water heaters are certified at 300 PSI (2068 kPa) test pressure and 150 PSI (1034 kPa) working pressure. All water connections are 3⁄4"(19mm)
NPT on 11" (703mm) centers on top of unit, all gas connections 1⁄2"(13mm). All models design certified by CSA International (formerly AGA and
CGA). Recovery based on rated efficiency.
Meets NAECA requirements. All natural gas models meet SCAQMD requirements.
Dimensions and specifications subject to change without notice
in accordance with our policy of continuous product improvement.
C
E & F
D
1/2” GAS
CONNECTION
SIDE WATER OUTLET
DRAIN VA LV E
SIDE WATER INLET
G
A
B
6.5 inch (16.5 cm)
Min. Diameter Hole in Wall
Y
11 9/16
X
11 1/2
7 3/16”
Boot Extension
H
Vitraglas®and Hydrojet®are registered trademarks of Bradford White®Corporation.
©2006, Bradford White Corporation. All rights reserved.
(LP) Propane Gas Inputs Recovery at
50°C Rise and 90°F Rise
Imp. U.S. Liters/
GPH GPH Hr.
DH1-504T6CX 48,000 BTU/H 14.1 KW 41 50 189
DH1-75S6CX 57,000 BTU/H 16.7 KW 48 60 227
§ Some states do not allow limitations on warranties. See complete copy of the
warranty included with this product. Indicated warranties apply to USA, Canada and
Puerto Rico installations.
A
Ht. to
Center Line
of Vent
in. mm.
U.S.
Gal.
Cap.
GPH Rec.
50˚C/90˚F Rise
Input
BTU KW
Vent
Dia.
in. mm.
Imp.
Gal.
Cap. Imp.
Gal. US GPH LPH
B
Jacket
Dia.
in. mm.
C
Ht. to
Top of
Heater
in. mm.
E
Ht. to
T&P
Conn.
in. mm.
F
Space
Htg.
Outlet
in. mm.
G
Space
Htg.
Inlet
in. mm.
D
Ht.to
Gas
Conn.
in. mm.
50,000
55,000
60,000
14.7
16.1
17.6
48
65
75
153⁄4
153⁄4
161⁄2
400
400
419
521⁄4
56
52
1327
1422
1321
4/6
4/6
4/6
102/152
102/152
102/152
Approx.
Shpg.
Wt.
Lbs. Kg.
197/89.4
243/110
281/127
40
54
62
43
47
51
53
58
63
201
220
238
751⁄4
781⁄4
751⁄2
1911
1988
1918
151⁄4
151⁄4
151⁄4
387
387
387
521⁄4
56
52
1327
1422
1321
20
22
241⁄2
508
559
622
583⁄4
62
59
1492
1557
1499
DH1-504T6BN(LP)
DH1-65T6BN
DH1-75S6BN(LP)
Liters
182
246
284
NATURAL GAS
Model
Number
105-B-HIDV-1106-A Printed in U.S.A.
Horizontal"X"
16 1/4 18 25 1/4 37 3/4 61 5/16
17 3/16 20 11/16 35 3/16 57 7/8 107 5/16
order order no add'l order order
11 9/16 kit F kit G kit req'd kit H kit I
16 5/16 *orderorder order order order
17 1/4 kit F (2) kit G & F kit F kit H & F kit F & I
18 1/16 order order order order order
20 3/4 kit F & G kit G (2) kit G kit G & H kit G & I
25 5/16order order order order order
35 1/4 kit F kit G kit H kit H (2) kit I
38 1/16order order order order order
57 15/16 kit H & F kit H & G kit H (2) kit H (3) kit H & I
61 3/8 order order order order order
Vertical "Y"
107 3/8 kit I & F kit I & Gkit I kit I & H kit I (2)
The standard vent kit (239-42979-00) is ordered and shipped separately. The
components are as follows: 4" vent tube*, 6" Air Intake Tube, Vent Terminal, Inner Wall
Term Mounting Flange, Outer Wall Term. Mounting Flange, Vent Terminal Hardware,
RTV Silicone Sealant, 4" Vent Elbow and a 6" Air Intake Elbow. The vent tube and air
intake tube telescopes from 13 3/4" to 23 11/16".