Bradford White RTG 199HE User manual

Installation Instructions
Models: RTG 199HE / RTG 199ME
Outdoor kit
Warning: This kit must be installed by a qualified
installer in accordance with these instructions and all
applicable codes and requirements of the authorities
having jurisdiction.
6 720 811 755 (2014/05) US

2
Key to symbols and safety instructions
Outdoor kit – 6 720 811 755 (2014/05)
1 Key to symbols and safety instructions
1.1 Key to symbols
Warnings
The following keywords are defined and can be used in this
document:
•DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
•WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
•CAUTION indicates a hazardous situation which, if not
avoided, could result in minor to moderate injury.
•NOTICE is used to address practices not related to
personal injury.
Important information
Additional symbols
2 Outdoor Installation
2.1 Warnings
Warnings in this document are identified by
a warning triangle printed against a grey
background.
Keywords at the start of a warning indicate
the type and seriousness of the ensuing risk
if measures to prevent the risk are not taken.
Thissymbolindicatesimportantinformation
where there is no risk to people or property.
Symbol Explanation
▶ Step in an action sequence
Cross-reference to another part of the
document
• List entry
– List entry (second level)
Table 1
DANGER:
The top of the outdoor kit will get very hot
during operation.
▶ Keep away from children. Install heater
in a location where the top of the kit
cannot be reached by small children.
DANGER: Flue gas is very hot and contains
carbon monoxide.
Flue gas will be released through the
outdoor kit.
▶ The outdoor kit cannot be installed on a
water heater mounted indoors. To
preventrisk of fire and carbonmonoxide
poisoning, maintain all clearances
indicated in these instructions.
DANGER:
▶ Do not place or store any combustible
material within 5 feet of the appliance.
Maintain specified clearance to
combustibles on the wall where the
appliance is installed and any adjacent
walls or overhang. Observe all
clearances required in this manual.
DANGER:
▶ Surface temperature of the kit is less
than 140 °F, except highest top surface
which may reach 300 °F.
DANGER:
▶ Do not mount water heater directly onto
vinyl siding, see Fig. 10.

3
Selecting heater location
Outdoor kit – 6 720 811 755 (2014/05)
2.2 This outdoor kit includes:
• Supports (2) with screws
• Sealing gasket
• Control panel shield
• Outdoor vent cap.
3 Selecting heater location
Beforeproceeding,readthe water heater installation manual. If
the information in that manual is not followed exactly, a fire,
explosion or poisoning by carbon monoxide may result causing
property damage, personal injury or death.
▶ This appliance is not designed to be installed outdoors in
climates that commonly fall below freezing (32 °F).
▶ Choose an outside wall for the installation. Installation on a
wall protected by an overhang above is recommended.
▶ Size the water and gas connections according to the
instructions in the water heater installation manual. Use
unions when connecting both water lines and gas supply
line to the heater.
3.1 Minimum clearances
If the appliance is installed under an overhang, there must be a
minimum 36” clearance from the top of the appliance and the
mounting area must be open in front and on the sides of the
appliance.
Fig. 1
DANGER:
The freeze prevention kit on the appliance is
designed to provide protection from
temperatures down to approximately 5 °F
for short term conditions only. It will not
protect the appliance in areas where the
temperature is routinely expected to be
belowfreezing.Thefreezepreventionkitwill
not protect plumbing outside the appliance
from freezing. Precautions must be taken:
▶ Always drain the water heater if it will be
exposed to long term freezing
conditions.
DANGER:
The water in this appliance is cold and
always remains cold except for the times
when the burner is on.
▶ In the event of power outage in
conjunctionwithfreezing temperatures,
it is recommended that the heater be
drained.
DANGER:
▶ Damage to the appliance from freezing
is not covered under the manufacturer's
warranty. Ref. Description
Min.
distances
A Directly below or adjacent to an
opening; operable windows, doors and
any fresh air openings
1 ft
B
C
D From any adjacent wall 1 ft
E Below a gutter, sanitary pipework,
eaves or overhang
3 ft
F Above ground 1 ft
G From a gas meter or gas regulator 3 ft
Table 2 Clearances
Best practice note: The clearances in Fig. 1
and table 2 are the minimum allowed by the
standard.
When possible consider maximizing the
clearances A, B, C, D and E to allow for the
effects of wind and frequently used door and
window openings.

4
Installing outdoor kit
Outdoor kit – 6 720 811 755 (2014/05)
4 Installing outdoor kit
4.1 Replace the control panel shield
▶ Loosen the two Philips head screws located on bottom rear
of cover (see Fig. 2).
Fig. 2 Loosen the two screws
▶ Remove the front cover panel and replace the original
control panel shield with shield provided in the kit, see Fig.
3.
Fig. 3 Replace the control panel shield
▶ After replacing the control panel shield re-position the
front cover.
▶ 1. Remove the cover plate (A) from the top of the
appliance, as shown in Fig. 4.
Fig. 4
▶ 2. Attach the supports (B) to the appliance with the four
provided screws, as shown in Fig. 4.
Before mounting the outdoor kit on the appliance:
Remove the exhaust seal from outdoor vent cap:
For condensing appliances only:
▶ Remove inner seal, see Fig. 5.
Fig. 5 Condensing appliances only (RTG 199HE)
WARNING:
▶ The control panel shield must always
remain closed, except when making
adjustments, to prevent damage to
heater from weather.
6720645551-16.1V

5
Installing outdoor kit
Outdoor kit – 6 720 811 755 (2014/05)
▶ 3. Attach the gasket provided with the kit as shown in Fig.
6.
Fig. 6
▶ 4. Install supplied Freeze Prevention Kit (separate
packaging). Follow separate installation instructions
provided with Freeze Prevention.
▶ Position the outdoor vent cap on the top of the appliance,
as shown in Fig. 7.
Fig. 7
▶ Attach the outdoor vent cap to the appliance by fastening
the two provided screws and washers, see Fig. 8.
Fig. 8
Note: Freeze Prevention is not designed
to protect the appliance during long
durations below freezing or to protect
plumbing outside the appliance. Always
drain the water heater if it will be exposed
to long term freezing conditions.
6720645551-15.1V
NOTE: Once this kit is installed, the outdoor
vent cap will need to be removed, before
removing front cover.

6
Mounting instructions
Outdoor kit – 6 720 811 755 (2014/05)
5 Mounting instructions
▶ The water heater is approved for installation directly on an
outside wall. Secure the wall mounting bracket provided
with the water heater to a wall surface. See Fig. 9.
▶ The installation method of the mounting bracket will
depend on the type of mounting surface. Due to the
varieties of building siding or surfacing, the installer must
decide how best to support and level the heater on an
outside wall. It is recommended that horizontal or vertical
support boards or plywood sheathing (1/2” minimum) first
be attached to the wall surface. The heater must also be
kept level on the wall surface.
Fig. 9 Installation on wood siding
Fig. 10 Installation on vinyl siding
6 Recess box - Outdoor installation
6.1 Warnings
WARNING: Do not mount heater directly to
vinyl siding.
▶ With vinyl siding, a 3½' x 4' area of the
siding must first be removed and then
replaced with wood or other non-plastic
material. See Fig. 10.
DANGER:
▶ The top of the outdoor kit will get very
hot during operation. Keep away from
children. Install heater in a location
where the top of the kit cannot be
reached by small children.
DANGER:
▶ Flue gas will be released through the
outdoor kit. Flue gas is very hot and
contains carbon monoxide. The outdoor
kit cannot be installed on a water heater
mounted indoors. To prevent risk of fire
and carbon monoxide poisoning,
maintain all clearances indicated in
these instructions.

7
Installations
Outdoor kit – 6 720 811 755 (2014/05)
7 Installations
7.1 Installation only with Recess box
This outdoor kit is intended to be installed together with recess
box.
Fig. 11 Mounting the heater inside recess box
Fig. 12 Close the recess box cover with Padlock
DANGER:
▶ Do not place or store any combustible
material within 5 feet of the appliance.
Maintain specified clearance to
combustibles on the wall where the
appliance is installed and any adjacent
walls or overhang. Observe all
clearances required in this manual.
DANGER:
▶ Surface temperature of the kit is less
than 140 °F, except highest top surface
which may reach 300 °F.
DANGER:
▶ The water in this appliance is cold and
always remains cold except for the times
when the burner is on. In the event of
power outage in conjunction with
freezing temperatures, it is
recommended that the heater be
drained.
DANGER:
▶ Damageto the appliance from freezing is
not covered under the manufacturer's
warranty.
6720644956-06.1V
6720644956-08.1V

8
Installations
Outdoor kit – 6 720 811 755 (2014/05)
7.2 Installing outdoor vent cap on the appliance
▶ 1. Attach the supports (A) to the appliance by fastening
with the four provided screws, as shown in Fig. 13.
Fig. 13
Before mounting the outdoor kit in the appliance:
▶ Position the outdoor vent cap on the top of the appliance,
as shown in Fig. 14.
Fig. 14
▶ Attach the outdoor vent cap to the appliance by fastening
the two provided screws and washers, see Fig. 15.
Fig. 15
Installation of frame in the heater
To install the protection grill in the heater;
▶ Tilt the frame on one direction, as showed in Fig. 16.
▶ Push the frame to fit the Outdoor vent cap.
Fig. 16
WARNING:
▶ The control panel shield must always
remain closed, except when making
adjustments, to prevent damage to
heater from weather.
A
6720644956-03.1V
A
6720645551-01.1V
NOTE: Once this kit is installed, the outdoor
vent cap will need to be removed before
removing the front cover.
6720645551-04.1V
1
2

9
Installations
Outdoor kit – 6 720 811 755 (2014/05)
▶ Place the protection grill in the Outdoor vent cap.
Fig. 17
▶ Fix the frame and protection grill with two screws.
Fig. 18
▶ Position the recess box cover as showed in Fig. 19.
Fig. 19
▶ Fix the frame to the recess box cover with 4 screws, 4 metal
washers and 4 silicone washers.
Fig. 20
6720645551-05.1V
6720645551-07.1V

10
Electrical connections
Outdoor kit – 6 720 811 755 (2014/05)
▶ Close the recess box cover with padlock (optional).
Fig. 21
8 Electrical connections
8.1 Electrical power supply
The water heater requires an electrical power supply from a
120VAC / 60Hz circuit (with a dedicated outlet) and must be
properly grounded.
The heater is wired as shown in the wiring diagram of the water
heater installation manual.
Fig. 22 Connecting power supply cord
[1] Power cord length: 3ft.
Note: Outlet appliance is plugged in to should be clear from
possible water damage.
▶ Refer to water installation manual to complete installation
of gas and water piping connections.
▶ Start and operate the water heater according to the water
heater installation manual. NOTE: Open the control panel
shield to access the controls of the heater.
WARNING:
▶ For safety reasons, disconnect the
power supply cord to the heater before
any service or testing is performed.
WARNING:
▶ This heater must be electrically
grounded in accordance with the most
recent edition of the National Electrical
Code. NFPA 70. In Canada, all electrical
wiring to the heater should be in
accordance with local codes and the
Canadian Electrical Code, CSA C22.1
Part 1. Do not rely on the gas or water
piping to ground the metal parts of the
heater
6720645551-08.1V
WARNING:
▶ Confirm that the water heater is
appropriately grounded and that the
installation meets all applicable
electrical codes for outdoor
installations.