BrandMotion 9002-2750v1 User manual

! INSTALLATION!INSTRUCTIONS!
9002-2750v1.doc instructions V1 7-12-16 Page 1 of 5 JM
MyFord Factory Display Radio Camera Interface
For 4.2” Display
(Kit # 9002-2750v1)
Please read thoroughly before starting installation and check that kit contents are complete.
Items Included in the Kit:
Tools & Supplies Needed:
Video input T-harness
Interface box
Instructions
Plastic trim removal tool
7 mm socket
Phillips screw driver
Wire strippers
Wire cutters
Electrical tape or Heat shrink
Safety Precautions:
•Work in well ventilated area that is clear of obstructions.
•Secure vehicle with tire chucks in both front and rear of tires.
•Turn vehicle accessories OFF and ensure ignition key is in OFF position.
•Wear safety goggles and snug fitting clothes.
•Use tools only for their intended purpose and which are in good repair.
•Only perform this task if confidence, skill, and physical ability permit.
NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color
instructions, as well as an installation video, please visit www.brandmotion.com

! INSTALLATION!INSTRUCTIONS!
9002-2750v1.doc instructions V1 7-12-16 Page 2 of 5 JM
1. Remove dash trim around screen/display in
dash.
2. Remove the screws holding the screen into
the dash.
3. Remove the screen from the dash.
4. Check compatibility of screen/display on the
last page of this install guide.
5. Remove the 6-pin connector from the
harness, if connected, then plug the
harness into the 6-pin connector on the
2750 module.
6. The camera will have to be powered form
an accessory circuit in the vehicle. (If not
the interface will not see the video input
and not show the camera on the screen.)
7. Disconnect the FCDIM/display harness on
the back of the display by pushing down
on the tab and pulling the “lever” back.
8. Connect the T-harness into the FCDIM first
from the 2750.

! INSTALLATION!INSTRUCTIONS!
9002-2750v1.doc instructions V1 7-12-16 Page 3 of 5 JM
9. Then connect the opposite end to the
vehicle harness, within 5 seconds turn the
key to the run/ignition position. (Do not
start the vehicle)
10. Wait 2 minutes for programming to
complete. The FCDIM should reset twice.
11. Test programming by placing the vehicle in
reverse. (Testing without a camera will
result in a “camera not available” message
and disable the camera input temporarily.
12. If programming did not work, turn the
ignition on, unplug 6-pin harness from the
2750 for 5 seconds, and replace
programming will restart.
13. Any camera with a RCA connector can be
used with this interface.
14. Mount module to top of radio/cd case in
dash, behind screen.

! INSTALLATION!INSTRUCTIONS!
9002-2750v1.doc instructions V1 7-12-16 Page 4 of 5 JM
Important Notes:
•Camera must be connected to RCA
connection and power before
testing. If camera is not properly
connected before vehicle is put into
reverse, a Camera not available
message will display and the
camera will not function until the
vehicle power is turn off and back
on.
•This interface can only be used on
one vehicle. After initial
programming this kit will be locked
to the VIN of the vehicle. There is
no reset or un-programming
procedure for this interface. If
vehicle modules are replaced or
reprogrammed to factor
specifications at the dealer, this kit
can be used to reprogram the same
vehicle to re-enable rear camera.
•Depending on vehicle configuration,
display may stay in reverse camera
mode until vehicle is driven to pre-
determined speed. This is a factory
function.
Find the part number on the back
of the display and verify
compatibility.

! INSTALLATION!INSTRUCTIONS!
9002-2750v1.doc instructions V1 7-12-16 Page 5 of 5 JM
If you do not see your part
number, call to verify
compatibility.
734-619-1250