Brandt AD995XC Specification sheet

AD995XC
COOKER HOOD
USE MANUAL
INSTALLATION INSTRUCTION

Table of Contents
• From the Manufacturer 3
• Specifications 4
• SAFETY : Read this first ! 5
• Description of Parts 7
• Ducted vs. Recirculation version 8
• Installation
Wall drilling and bracket fixing 9
Mounting the hood body 11
Connections 11
Chimney assembly 13
• Cleaning & Maintenance 13
• Operation 14
• Troubleshooting 15
• Schematic Diagram 15
2
Troubleshooting
Schematic Diagram
Symptoms Possible Cause Action
Ensure the plug
Motor does not No electrical supply is connected properly.
working Reset circuit breaker.
Aluminum Clean the filters and
Poor airflow filters clogged replace when dry
Charcoal filters Replace the new
clogged charcoal filters
Motor running but Butterfly valve Contact technician
no airflow jammed
High temperature The kitchen is not
Motor cuts after a safety device activated. sufficiently ventilated.
few minutes The hood is installed too The hood must be at
near the cooking stove. least 75cm from stove.
Oil dripping onto Aluminum filter Wash the aluminum
stove saturated. filters.
Whirring sound Foreign object in contact Contact technician.
with fan blade.
Lamps do not Lamps are burnt out. Change the lamps.
light up Lamps are loose. Tighten the lamps.
15

4
Specifications
Input :
Absorbtion :
Motor :
220-240V 50-60Hz
408 W ( LED)
400W
External Dimensions
Dimension
Model L H1 H2 H3
AD995XC 900mm 470mm 470mm 80mm
Chimney assembly
Upper chimney
• Slightly widen the two sides of the upper chimney and hood them behind
the mounting brackets, ensuring that they are well seated.
• Secure the sides of the brackets using 4 screws (M3 X 12).
Lower chimney
• Slightly widen the two sides of the chimney and hook them between the
upper chimney and the wall, ensuring that they are well seated.
• Fix the lower parts laterally to the hood body using 2 screws (ST4 X 8).
•
Cleaning & Maintenance
SURFACES : Wash with warm soapy water and a soft sponge. Never use
abrasive detergent, scouring pads, steel wool or solvents on any part of this
appliance as this will cause irreparable damage. Dry the kitchen hood using
a cloth that does not produce fluff.
BAFFEL FILTERS : Wash in the dishwasher, it is advisable to stack them
vertically to avoid food residue sticking to them. Or soak it in a degreas-ing
agent until grease dissolve and rinsing them under the tap, then rinse off.
13

RECIRCULATION MODE AIR OUTLET
• Insert the connection extension pieces
laterally in air outlet connection.
• Make sure that the outlet of the extension
pieces is horizontally and vertically
aligned with the chimney outlets.
• Connect the air outlet connection to the
hood body outlet using either a flexible or
rigid pipe with ∅150mm.
• Ensure that the activated charcoal filters
have been inserted.
ELECTRICAL CONNECTION
• The electrical tension must correspond to the tension noted on the label
placed inside the cooker hood.
• Connect the electrical plug, where provided, to the an easily accessible
outlet in conformity with local standards in force.
• Where an electrical plug is not provided (for direct connection to
electrical network) place a standards approved bipolar switch with an
aperture distance of not less than 3mm (accessible) from the contacts.
Attention: substituting the supply cable must be carried out by authorized
technical assistance service.
Air outlet
connection
12
SAFETY : Read this First !
• Do not connect the appliance if there are obvious signs of transportation
damage.
• Read this user manual thoroughly before attempting to use this
appliance.
• Installation and repair should be attempted only by qualified technical
personnel.
• It is dangerous to modify any part of this appliance.
• The manufacturer declines all responsibility in case of failure to adopt
proper safety measures.
• Ensure the location in which this appliance is installed has good,
permanent ventilation.
• The distance between the bench top to the
lower part of the hood must not be at least 75
cm or higher.
• The exhaust from the canopy range hood
must not be discharged into any heating flue,
which may carry combustion products from
other sources.
• Do not leave lit gas burners exposed due to
risk of fire.
• Use an electrical connector with earth that is
correct for your location.
• Check that the voltage in your area is correct
before plugging in.
• The electrical connection of this appliance must be connected to earth.
Green & yellow = EARTH
Blue = NEUTRAL
Brown = LIVE
5

• This appliance should be connected directly to the fused disconnect (or
circuit breaker) through flexible, armored or nonmetallic sheathed cop-
per cable.
• Multiple plugs and extension cables must not be used. Overload is
dangerous and may cause a fire.
• Ensure that the power chord is free from any heat source or sharp
objects.
• The appliance should be switched off and the electrical supply
disconnected before any cleaning or maintenance work can be carried
out.
• Allow some slack in the cable so the appliance can be moved if servicing
is ever necessary.
Lack warning:
1) This appliance Is not Intended for use by persons (Including children)
with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction con-
cerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appli-
ance.
2) If the supply cord is damage, it must be replaced by the manufacturer, and
use the genuine parts only .
3) There is a fire risk if cleaning is not carried out in according with the in-
structions.
6 11
Aligning the hood body
• Before attaching the hood body, adjust the two screws located on the
hood body mounting points.
• Hook the hood body onto the support screws and tighten the support
screws fully.
• Adjust screws to level the hood body.
Connection
DUCTED MODE AIR EXHAUST SYSTEM
• When installing the ducted mode, connect the hood
to the chimney using either a flexible or rigid pipe
with ∅150mm.
• Fix the pipe in position using sufficient pipe clamps
(not supplied).
• Remove any activated charcoal filters.

• Mark the center of the bracket holes and drill φ8mm holes. Insert wall
plug in the wall. Secure mounting bracket firmly using 2 (ST5 x 25)
screws.
• Fix the upper chimney cover to both mounting bracket using 2 (M3 x 12)
screws.
• Slide the lower chimney cover downwards and ensure that it is well
seated on the hood body.
10
Description of Parts
AD995XC
A. Chimney Mounting Bracket
B. Upper Chimney Cover
C. Lower Chimney Cover
D. Motor Housing
F. Baffel Filters
7

Ducted vs. Recirculation mode
You can choose to install the hood as a ducted or recirculation mode :-
• Ducted mode (Vented mode)
In the ducted mode, air is drawn into the hood, fat are trapped by aluminum
filters. Odors, fumes and condensation are then expelled to the outside. In
this mode, only the aluminum filters are installed.
• Recirculation mode
In the recirculation mode, air is drawn into the hood, fats are trapped by the
aluminum filters, the air then passes through charcoal filters to remove cook-
ing odors, the purified air is then passed back into the kitchen. In this mode,
both the aluminum filters and the charcoal filters must be installed.
8
Installation
Wall drilling and bracket fixing
9
300
545-1010
80
898
110
232