Braun Corporation UVL Series User manual

Under-Vehicle Lift®
W
A
RNING
Read manual
before installing
or servicing lift.
Failure to do so
may result in
serious bodily
injury and/or
property damage.
ual
Man
"Providing Access to the World"
International Corporate Hdqrs: P.O. Box 310 Winamac, IN 46996 USA
1-800-THE LIFT®[phone] FAX: [phone]
®
®
Braun UVL SeriesTM
Braun UVL SeriesTM
CJKA-**HB
CJKA-**HB
Public Use Wheelchair Lifts
01
Series 01
Service Manual for:
33392 Rev. A
May
2007 Patent #4,958,979
Patent #4,958,979
www.braunlift.com®
DOT — Public Use Lift
DOT — Public Use Lift
“DOT — Public Use Lift” verifies that this platform lift meets the
“public use lift” requirements of FMVSS No. 403. This lift may be
installed on all vehicles appropriate for the size and weight of the
lift, but must be installed on buses, school buses, and multi-
purpose passenger vehicles other than motor homes with a gross
vehicle weight rating (GVWR) that exceeds 4,536 kg (10,000 lb).

NUVL855SM
e5*72/245*95/54*0102*00
1-800-THE LIFT®
BRAUNLIFT.COM®
The Braun Corporation
DOT Public Use Lift MODEL#
Max. Lifting Capacity - 750 lbs.
U.S. PATENT 4958979
MFG DATE
PUMP CODE CYLINDER
01-00025
SERIAL NUMBER
02/28/05
We at The Braun Corporation wish to express our fullest appreciation
on your new purchase. With you in mind, our skilled craftsmen have designed and
assembled the finest lift available.
This manual provides service-related material. Refer to the FMVSS No. 403
Quick Reference Installation Sheet for installation instructions, operating instructions
and maintenance procedures.
Braun UVL Series™lifts are built for dependability and will provide years of plea-
sure and independence as long as the lift is installed and serviced as specified by a
Braun certified technician, and the lift is operated by an instructed person.
Sincerely,
THE BRAUN CORPORATION
Ralph W. Braun
Chief Executive Officer
OWNER'S WARRANTY REGISTRATION
PURCHASED FROM
DATE INSTALLED
NAME
ADDRESS
CITY
TELEPHONE
TO VALIDATEWARRANTY
REGISTRATION CARDS MUST BERETURNED TO THEBRAUN CORPORATION.
OWNER
STATE ZIP
Sample Warranty/Registration Card
Two Braun Serial No./Series No. identification tags (shown below) are posted on the lift. One
I.D. tag is posted on the left platform side plate (outboard end). A second I.D. tag is located
inside of the pump module. Both I.D. tags provide the product identification information
provided on the warranty/registration card. Record the information in the space provided (or
document on a copy). This information must be provided when filing a warranty
claim or ordering parts.
Warranty and Registration Instructions
Immediately upon receiving the lift, examine the
unit for any damage. Notify the carrier at once
with any claims.
Two warranty/registration cards (shown right) are
protected in a clear envelope and attached to the
lift protective shipping wrap. The sales representa-
tive must process one of the cards. The consumer
must fill out the other card and mail it to The Braun
Corporation. The warranty is provided on the back
cover of this manual. The warranty cards must
be processed to activate the warranty.
Congratulations
Model No.
Series No.
Serial No.
Pump Code
Cylinder Code
Date of Manufacture
6DPSOH6HULDO1R6HULHV1R,GHQWLÀFDWLRQ7DJ
NUVL855SM-01-00025
Serial No.Model No.
Series No.

Page 1
Contents
Troubleshooting and Maintenance
Lift Terminology ............................................................ 2
Switch and Sensor Locations ..................................... 3
&HUWLÀFDWLRQ&KHFNOLVW'LDJQRVWLF3URFHGXUHV ......... 4
Adjustments and Calibration ....................................... 5
7HUPLQDO6WULSDQG'RRU2SHUDWRUV............................. 6
Floor Level and Inner Roll Stop Adjustments ......... 6-9
/XEULFDWLRQ'LDJUDP................................................... 10
Maintenance and Lubrication Schedule............... 11-13
7URXEOHVKRRWLQJ'LDJQRVLV&KDUW......................... 14-17
Notes ............................................................................ 18
Lift Wiring Schematic ................................................. 19
Hydraulics
+\GUDXOLFV3DUWV/LVW .................................................. 20
+\GUDXOLFV'LDJUDP .................................................... 21
5HSDLU3DUWV
3XPS0RGXOH
 3XPS0RGXOH3DUWV/LVW ....................................... 22
 3XPS0RGXOH'LDJUDP ......................................... 23
Lift Exploded Views
Complete Lift.......................................................... 24
5HSDLU3DUWV/LVW ................................................... 25
+RXVLQJ'HWDLO........................................................ 26
&DUULDJH'HWDLO........................................................ 27
3ODWIRUP'HWDLO........................................................ 28

Page 2
W
ARNING
81823
PushT-handleinfullyand
manuallymoveplatformin
andouttoengageplatform
lockbeforedrivingvehicle.
Failuretolock platform may
resultinunintended platform
deployment.Unintended
platformdeploymentmay
resultinseriousbodilyinjury
and/orpropertydamage.
Donot remove!
DOORSTOW
DOWNUP
Outboard
Right
Left
Inboard
Lift Terminology
Lift Mounting
Brackets (6)
Hydraulic
Cylinders
Lifting
Arms
Rolling
Horizontal Arms
Outer Barrier
Actuator
Outer
Barrier
Platform Cable-activated
Manual Release System
Hand-Held Attendant's
Control Box
Pump
Module
Inner
Roll Stop
Lift Housing
Carriage
Torque
Tube
Platform

Page 3
Switch and Sensor Locations
W
ARNING
81823
PushT-handleinfullyand
manuallymoveplatformin
andouttoengageplatform
lockbeforedrivingvehicle.
Failuretolockplatformmay
resultinunintendedplatform
deployment.Unintended
platformdeploymentmay
resultinseriousbodilyinjury
and/orpropertydamage.
Donotremove!
DOORSTOW
DOWNUP
Pressure
Transducer
30426
Outer Barrier
Limit Switch
73950NA
Full Out Cam
73775
Stow Start
Limit Switch
73950A
Floor Level
Limit Switch
73950A
Floor Level
Cam
73712
Stow Start
Cam
73712
Lift Out Cam
75776CN
Full Out
Limit Switch
73950A
Lift Out
Limit Switch
73950A

Page 4
7KHIROORZLQJRSHUDWLRQVDQGFRQGLWLRQVPXVWEHIXQFWLRQDOO\YHULÀHGLQRUGHUIRUWKHOLIWWREH)0966
403/404 compliant. If an operation does not function as described or a condition is not met, follow the refer-
enced procedures to correct the problem or contact a Braun Corporation Product Support representative at
7+(/,)7®.
9HKLFOHPRYHPHQWLVSUHYHQWHGXQOHVVWKHOLIWGRRULVFORVHGHQVXULQJWKHOLIWLVVWRZHG
 9HULI\OLIWVWRZHGVLJQDOSLQLQWKHFRQGXFWRUSOXJRQWKHVLGHRIWKHSXPSPRGXOHKDVDYROW
signal.
2. Refer to the interlock installation instructions.
• Lift operation shall be inhibited unless the vehicle is stopped and vehicle movement is prevented.
 9HULI\YHKLFOHVHFXUHVLJQDOSLQLQWKHFRQGXFWRUSOXJRQWKHVLGHRIWKHSXPSPRGXOHKDVD
volt signal.
2. Refer to the interlock installation instructions.
• The platform will not fold/stow when occupied.
- Refer to Platform Sense Calibration.
• The inner roll stop will not raise if occupied.
- Refer to Inner Roll Stop Occupied Sensor Adjustment
• The outer barrier will not raise if occupied.
- Refer to Outer Barrier Occupied Calibration procedure
9HULI\SODWIRUPOLJKWLQJZKHQOLIWLVGHSOR\HGDQGSHQGDQWLOOXPLQDWLRQZKHQOLIWLVSRZHUHG
1. Replace bulb(s) in the light housing.
2. Check inline fuse on wires going out to lights.
• An audio warning (and visual warning for public lifts) will activate if the threshold area is occupied when
WKHSODWIRUPLVDWOHDVWEHORZÁRRUOHYHO
1. Make sure connectors to threshold mat are properly connected.
2. Call Product Support.
• Platform movement is prohibited beyond the position where the inner roll stop is fully deployed (up).
- Call Product Support.
• Lift platform movement shall be interrupted unless the outer barrier is deployed (up).
- Check outer barrier limit switch, wires and connector.
- LED D29 should not be illuminated when outer barrier is deployed (up).
Certification Checklist Diagnostic Procedures

Page 5
Adjustments and Calibration
$GMXVWPHQW3URFHGXUHV
/LIW2XW6ZLWFK The Lift Out Switch stops inward
travel of the carriage/platform during Stow function
(activated by the housing-mounted Lift Out Cam).
Move cam in to increase inward travel. Move cam
out to decrease inward travel. LED D25 will be il-
luminated when the switch is not contacting the cam.
)XOO2XW6ZLWFK7KH)XOO2XW6ZLWFKVWRSVRXW-
ward travel of the carriage/platform during Deploy
(Up/Down) functions (activated by the housing-
PRXQWHG)XOO2XW&DP0RYHFDPLQWRGHFUHDVH
outward travel. Move cam out to increase outward
travel. Carriage rollers must be inside housing a
minimum 1/2". The platform will not raise or lower
until this switch is activated. LED D26 will be illumi-
nated when the switch is contacting the cam.
)ORRU/HYHO6ZLWFK LED D28 will be illuminated
when the switch is contacting the cam. Detailed on
page 6.
%HORZ6WRZ The Below Stow Switch controls
the height of the carriage/platform before it moves
inward during the Stow function (activated by the
torque tube-mounted Below Stow Cam). Rotate the
cam in to decrease platform height. Rotate the cam
out to increase platform height. Adjust cam so lifting
DUPVDUHDOLJQHG9LHZWKHSODWIRUPSRVLWLRQLQWKH
housing. LED D24 will be illuminated at stow level
and below.
%DUULHU'RZQ6ZLWFK This platform-mounted
switch prohibits the platform from raising unless
the outer barrier is in the full up position. The Up
function is prohibited if the outer barrier detent pin is
not fully engaged also. LED D29 will be illuminated
when the switch is not contacting the outer barrier
detent pin.
'ULYH&KDLQ$GMXVWPHQW
In event the drive chain sags 1/2" or more, adjust
tension as detailed. Tighten to eliminate visible sag
but do not overtighten.
1. Remove bottom pan.
2. Pull the manual release cable and lock.
3. Remove adjustment bolt (tensioner) access
cover.
4. Loosen inside jam nut. Secure tensioner and
tighten outside jam nut. Tighten to eliminate vis-
ible chain sag but do not overtighten.
5. Lock jam nuts together making sure the ten-
sioner roller is horizontal. Release and push the
manual cable in fully. Ensure platform is locked
by moving the platform in and out until chain
release assembly engages chain.
&DOLEUDWLRQ3URFHGXUHV
3ODWIRUP6HQVH&DOLEUDWLRQ
1. There must be no weight on platform.
2. Press handheld pendant UP switch to raise plat-
form a minimum 3" above stow level.
3. Remove pump cover and press and hold control
board mounted CAL. 50 lb. button. While pressing
the CAL. 50 lb. button, press and hold the hand-
held pendant STOW switch (button). The platform
will lower to stow level (begin stow function), and
then start to raise. Release CAL. 50 lb. button
immediately when platform starts to raise from
stow level.
4. LED D18 will be illuminated when weight on plat
form prevents stowing.
Ground Sense Calibration
1. Press handheld pendant DOWN switch to lower
platform fully to ground level.
2. While continuing to press the pendant DOWN
switch, press and then release control board
mounted CALIB. GND SEN/OB button.
3. Release the pendant DOWN switch.
4. LED D23 will be illuminated when platform is at
ground level.
2XWHU%DUULHU2FFXSLHG&DOLEUDWLRQ
1. Press handheld pendant DOWN switch to lower
platform fully to ground level.
2. Once outer barrier is fully unfolded (ramp posi-
tion), release the pendant DOWN switch.
3. Press and hold the control board mounted CALIB.
GND SEN/OB button. While holding CALIB.
GND SEN/OB button, press handheld pendant
UP switch to raise the outer barrier. Be sure to
release CALIB. GND SEN/OB button when outer
barrier reaches approximately half full up (verti-
cal) position.
Carriage Ride Height Adjustment
The carriage horizontal arms move (roll) in and out
RIWKHKRXVLQJWUDFNVRQUROOHUEHDULQJV)ROORZ-
ing installation or extensive lift operation, clearance
between horizontal arms and tracks may diminish.
The eccentric shaft mounting plate allows height
adjustment.
Remove eccentric plate mounting screw. Using
screwdriver or small rod, rotate the shaft clockwise
to increase carriage height. Rotate the shaft coun-
terclockwise to decrease carriage height. Reinstall
mounting screw in nearest retainer hole. Adjust left
and right side eccentric shafts (screw positions may
vary from side to side). Adjust height such that hori-
zontal arms do not contact top or bottom of tracks
(align center).

Page 6
Terminal Strip and Door Operators
3RZHU'RRU2SHUDWRUV
Black
Jumper
12345678910
Terminal Strip
The pump-mounted terminal
strip provides additional inputs
and outputs that can be used
for optional door operators,
beepers, interlocks, etc. - as
well as the door safety switch.
The black jumper wire must be
installed in terminals 6 and 9
to supply power to the circuit
board.
C_SW
1
O_RL
2
N/C
3
IN_LK
4
12_V
5
PWR
6
GND
7
F_LV
8
O_SW
9
C_RL
10
To Door Openers
“Close” Trigger
To Door Openers
“Open” Trigger
Full Open
Orange
Red
Door Cutout Black
Blue
Install optional power
door operators as
detailed in the instruc-
tions supplied with
door operator kit.
Route the wires to
the pump module and
connect to the termi-
nal strip as shown.
Floor Level and Inner Roll Stop Adjustments
$FKLHYLQJSURSHUÁRRUOHYHOSRVLWLRQLQJRIWKHSODW-
form and inner roll stop requires a combination of
)ORRU/HYHOVZLWFKDGMXVWPHQWDQGLQQHUUROOVWRS
adjustment. Both are factory set but must be in-
spected during installation procedures (will vary per
vehicle application).
Ensure the lift is positioned and secured as speci-
ÀHGRQ4XLFN5HIHUHQFH,QVWDOODWLRQ6KHHWVXS-
plied with lift) panels 1 and 2. Adjust the Floor
Level switch ÀUVW(detailed below). Then, adjust
the inner roll stop as detailed in Inner Roll Stop
Adjustment Instructions (adjust only if necessary).
The inner roll stop must rest properly on the vehicle
ÁRRUIRUZKHHOFKDLUHQWU\DQGH[LW
7KH)ORRU/HYHOVZLWFKVWRSVXSZDUGWUDYHORIWKH
platform during the Up function (activated by the
WRUTXHWXEHPRXQWHG)ORRU/HYHOFDP
Position the bottom of the lift platform 1 1/2" above
ÁRRUOHYHOWKUHVKROGPDWusing the manual op-
eration system.'RQRW operate the lift with the
electric pump during adjustment procedures.
Loosen the clamp securing the torque tube-mount-
HG)ORRU/HYHOFDP5RWDWHWKHFDPXQWLOWKH)ORRU
Level switch is activated (cam depresses switch).
1RWH&KHFNWKHÁRRUOHYHOSRVLWLRQRIWKHSODWIRUP
and the inner roll stop after powering the pump.
Hydraulic pressure may affect platform height
VOLJKWO\)LQHWXQLQJDGMXVWPHQWWZHDNLQJRIWKH
)ORRU/HYHOVZLWFKPD\EHUHTXLUHG
Floor Level Switch Adjustment
Adjust the Floor Level switch ÀUVW
(before adjusting the inner roll stop)!
)ORRU/HYHO6ZLWFK
)ORRU/HYHO&DP
Torque Tube
A
Cam depressing switch.

Page 7
O
P
E
N
C
L
O
S
E
VALVE
2. Position the lift platform below
stow level using the manual op-
eration system. See Photo C.
Lowering the platform will al-
low access to the cam bolt
securement nut. See Photo E.
Inner Roll Stop Adjustment
&$87,21
'RQRWDGMXVWLQQHU
UROOVWRSOLQNDJHURG
/LQNDJHURGDGMXVW-
ment may result in
lift damage.
'RQRWDGMXVW
inner roll stop
OLQNDJHURGDW
WKLVWLPHLink-
age rod adjust-
ment is not
required unless
extra usable
platform length
is needed. If the
angle of the inner roll stop (when in the vertical
position) restricts the usable platform length
for the wheelchair passenger, adjustment of
the linkage rod will change the angle.
With the platform at ground level and the inner
roll stop in the vertical position, there should
be a minimum of 1” clearance between the
inner roll stop and torque tube.
Adjust the inner roll stop as detailed in the
following procedures. Then, adjust the linkage
rod as detailed on page 9 (only if necessary).
Inner Roll Stop
Linkage Rod
1.5DLVHWKHOLIWSODWIRUPIXOO\ÁRRUOHYHOus-
ing the manual operation system (Manual
2SHUDWLQJ,QVWUXFWLRQVGHWDLOHGRQ4XLFN
Reference Installation Sheet). If the inner
UROOVWRSUHVWVSURSHUO\RQWKHÁRRUdo not
adjust the inner roll stop. Lower the platform
to ground level. If the angle of the inner roll
stop (when in the vertical position), does not
restrict the usable platform length for the
wheelchair passenger, disregard inner roll
stop adjustment procedures. See Photo H
on page 9. Refer to the following procedures
if adjustment is required. Stow Level
Platform
below
Stow
Level
W
ARNING
81823
Push T-handlein fully and
manually move platform in
and out to engage platform
lock before driving vehicle.
Failure to lock platform may
result in unintended platform
deployment. Unintended
platform deployment may
result in serious bodily injury
and/or property damage.
Do not remove!
B
C
Hand
Pump
9DOYH
Pump
Handle
Figure A
0DQXDO2SHUDWLRQ6\VWHPV
T-Handle
Release
Cable
Floor Level and Inner Roll Stop Adjustments

Page 8
Inner Roll Stop Adjustment
3. Remove the 1/4"lock nut se-
curing the lifting arm cam bolt.
See Photos D and E. Do not
remove the bolt.
5DLVHWKHSODWIRUPIXOO\ÁRRU
level) using the manual op-
eration system.
Remove the cam securement
bolt (lift inner roll stop to relieve
pressure on bolt).
Allow the inner roll stop to rest
RQWKHÁRRU
Rotate the cam so the cam fol-
lower bearing engages the cam
QRWFKVDGGOH6HH3KRWRV)
and G.
Reinstall the cam securement
bolt in one of the three lifting
arm holes that best lines up
with one of the nine holes in the
FDP6HH3KRWRV)DQG*
Reposition the securement bolt
lock nut. 1RWH Lowering the
platform will allow access to
cam bolt. Tighten securely.
1/4" Lock Nut
Cam Bolt
Cam Notch (Saddle)
Cam
(9 available holes)
Lifting Arm
(3 available holes)
Rocker
Slider Block
Cam Notch (Saddle)
Engaging
&DP)ROORZHU%HDULQJ
'
E
FG
R
o
t
a
t
e
C
a
m
R
o
t
a
t
e
C
a
m
Floor Level and Inner Roll Stop Adjustments

Page 9
Inner Roll Stop
Linkage Rod
I
Inner Roll Stop Occupied Sensor Adjustment
'RQRWDGMXVWWKH
inner roll stop
OLQNDJHURGXQ-
less extra usable
platform length is
needed. See Photo
H. If the angle of
the inner roll stop
(when in the vertical
Linkage rod adjustment affects angle
of inner roll stop (vertical position).
&$87,21
Improper inner roll
VWRSOLQNDJHURG
adjustment may
result in lift damage.
position) restricts the usable platform length for the
wheelchair passenger, adjustment of the linkage rod
will change the angle.
Adjust the inner roll stop as detailed in the previous
procedures. Then, adjust the linkage rod as de-
tailed (only if necessary). If the linkage rod is ad-
justed too long or too short, it will exceed the travel
of the slider block resulting in damage to the cam
follower bearing, the cam and/or other components.
1. Position the lift platform below stow level using
the manual operation system.'RQRW oper-
ate the lift with the electric pump during adjust-
ment procedures.
2. Loosen the jam nuts at each end. Adjust rod
length as needed. Minimize adjustment. Care-
fully check the inner roll stop angle and opera-
tion using the manual operation system.
Ensure the rod has not been over adjusted
resulting in pressure on components (damage
will result). Tighten the linkage rod jam nuts.
H
Floor Level and Inner Roll Stop Adjustments
1. The optimum setting for the inner roll stop
occupied sensor adjustment nut is to have
just enough pressure to fold and unfold the
inner roll stop without triggering the inner roll
stop occupied sensor. This provides the most
weight sensitive setting while allowing the
unoccupied inner roll stop to function correctly.
2. If the weight of the empty inner roll stop is
triggering the sensor while it is folding, tighten
the sensor nut an 1/8 turn and cycle the lift
several times to verify correct operation.
3. If the lift is not reacting to weight on the inner
roll stop soon enough, loosen the pressure
adjusting nut an 1/8 turn and cycle the lift
several times to verify correct operation. J
Adjustment Nut

Page 10
W
ARNING
81823
PushT-handleinfully and
manuallymoveplatform in
andouttoengageplatform
lockbeforedriving vehicle.
Failuretolock platform may
resultinunintended platform
deployment.Unintended
platformdeploymentmay
resultinseriousbodilyinjury
and/orpropertydamage.
Donot remove!
DOORSTOW
DOWNUP
6SHFLÀHGUHFRPPHQGHG $YDLODEOH %UDXQ
 /XEULFDQW 7\SH /XEULFDQW $PRXQW 3DUW1R
/2/LJKW2LO
SG - Synthetic Grease Synthetic Grease Mobiltemp SHC32 12.5 oz.
(Multipurpose) Tube
Light Penetrating Oil LPS2, General Purpose 11 oz.
(30 weight or equivalent) Penetrating Oil Aerosol Can
Stainless Stick Door-Ease 1.68 oz.
Style (tube) Stick (tube)
'('RRU(DVH
15807
15806
28598
See the Maintenance/Lubrication Schedule for recommended applications per number of cycles.
Maintenance and Lubrication
Lubrication Diagram
Hydraulic
Cylinder
Pivot
Points
/2
Drive Chain and Rollers
/2
Drive Chain
Release Latch
SG
Torque Tube
Pivot Points
/2
Outer Barrier
and
Lower Closure
Pivot Points
/2
Outer Barrier
Detent Pin
/2
Lifting Arm
Pivot Points
/2
Platform Cable-activated
Manual Release System
Lifting Arm
Pivot Points
/2
Inner Roll Stop
Hinge
Pivot Points
/2
Torque
Tube
Pivot
Points
/2
Eccentric
Shaft
Rollers
(bearings)
/2
Inner Roll Stop
Linkage
Pivot Points
/2
Eccentric
Shaft
Rollers
(bearings)
/2
Rolling
Horizontal
Carriage Arm
Slot Area
'(

Page 11
Maintenance and Lubrication Schedule
Maintenance and
lubrication procedures
must be performed as
VSHFLÀHGE\DQ
authorized service
technician. Failure to
do so may result in
serious bodily injury
and/or property
damage.
W
ARNING
Proper maintenance is necessary to ensure safe,
troublefree operation. Inspecting the lift for any wear,
damage or other abnormal conditions should be a part
of all transit agencies’s daily service program. Simple
inspections can detect potential problems.
The maintenance and lubrication procedures speci-
ÀHGLQWKHIROORZLQJVFKHGXOHmust be performed
by a Braun authorized service representative at the
scheduled intervals according to the number of cycles.
1+76$189/6HULHVOLIWVDUHHTXLSSHGZLWKDF\FOH
counter (digital display built into the electronic control
board).
189/6HULHVOLIWVDUHHTXLSSHGZLWKKDUGHQHGSLQVDQG
self-lubricating bushings to decrease wear, provide
smooth operation and extend the service life of the lift.
When servicing the lift at the recommended intervals,
LQVSHFWLRQDQGOXEULFDWLRQSURFHGXUHVVSHFLÀHGLQWKH
previous sections should be repeated. Clean the com-
ponents and the surrounding area before applying
lubricants. LPS2 General Purpose Penetrating Oil is
recommended where Light Oil is called out. Use of im-
proper lubricants can attract dirt or other contaminants
which could result in wear or damage to the compo-
nents. Platform components exposed to contaminants
when lowered to the ground may require extra atten-
tion. Lift components requiring grease are lubricated
during assembly procedures. When replacing these
components, be sure to apply grease during installation
SURFHGXUHV6SHFLÀHGOXEULFDQWVDUHDYDLODEOHIURP
The Braun Corporation (part numbers below).
All listed inspection, lubrication and maintenance pro-
cedures should be repeated at “750 cycle” intervals
following the scheduled “4500 Cycles” maintenance.
These intervals are a
general guideline for
scheduling mainte-
nance procedures and
will vary according to
lift use and conditions.
Lifts exposed to severe
conditions (weather,
environment, contami-
nation, heavy usage,
etc.) may require
inspection and main-
tenance procedures
to be performed more
RIWHQWKDQVSHFLÀHG
0DLQWHQDQFH,QGLFDWRUThe Lift Ready green LED
mounted on top of the pump cover will change color
to yellow after every 750 cycles. The yellow LED will
not affect the functions of the lift, but is a reminder to
complete necessary maintenance and lubrication.
Once the lift has been serviced, press the CYCLE but-
ton (located below LCD display on the control board)
until the Lift Ready LED changes back to green. The
CYCLE button also clears the lift cycle count (since
last service) but not the lifetime cycle count.
'LVFRQWLQXHOLIWXVHLPPHGLDWHO\ if maintenance and
lubrication procedures are not properly performed,
or if there is any sign of wear, damage or improper
operation. Contact your sales representative or call
7KH%UDXQ&RUSRUDWLRQDW7+(/,)7®. One
of our national Product Support representatives will
direct you to an authorized service technician who will
inspect your lift.
750
Cycles
Outer barrier and lower closure pivot
points (2)
Outer barrier detent pin pivot points (2)
Inner roll stop hinge pivot points
Inner roll stop linkage pivot points
Lifting arm center and platform pivot
points (bearings at all points)
Inspect outer barrier and lower closure
for proper operation
Inspect outer barrier seal and lower
closure gasket
Inspect outer barrier detent pin hairpin
cotter
Inspect lift for wear, damage or any
abnormal condition
Apply Light Oil - See Lubrication Diagram
Apply Light Oil - See Lubrication Diagram
Apply Light Oil - See Lubrication Diagram
Apply Light Oil - See Lubrication Diagram
Apply Light Oil - See Lubrication Diagram
Correct or replace damaged parts.
Resecure, replace or correct as needed
Ensure hairrpin cotter is present and can be removed
and inserted easily. Resecure, replace or correct as
needed.
Correct as needed.

Page 12
Maintenance and Lubrication Schedule
1500
Cycles
750
Cycles
Inspect lift for rattles
Check drive chain tension.
Inspect inner roll stop and linkage for:
• Proper operation. Roll stop should rest solidly on
ÁRRUSURYLGLQJVPRRWKWUDQVLWLRQ
• Positive securement
• Wear or damage
Check carriage ride height in housing
Check stow height/lifting arm alignment
Inspect wiring harnesses for securement, wear or
other damage
Check lower pan securement
Torque tube pivot bearings (4 places)
Correct as needed.
Pull out and lock manual release cable. Adjust
chain tension as needed. See Drive Chain
Adjustment.
Resecure, replace or correct as needed. See
Inner Roll stop Adjustment Instructions.
Adjust as needed. See Carriage Ride Height
Adjustment.
Lifting arms should be horizontal, aligned with
each other and aligned with carriage. Adjust as
needed. See Switch Adjustment (Below Stow
Switch).
Resecure, replace or correct as needed
Resecure, replace damaged parts or correct as
needed.
Apply Light Oil - See Lubrication Diagram
Apply Light Oil - See Lubrication Diagram
Apply Door-Ease - See Lubrication Diagram.
Apply to the surface area around both slots and
wipe off excess.
Apply Light Oil - See Lubrication Diagram
Apply Light Oil - See Lubrication Diagram
Apply Synthetic Grease - See Lubrication
Diagram
Use compressor and nozzle to remove all debris
from housing. Clean outboard lower pan slot
and apply Antisieze to slot before reinstalling
pan.
Use clean cloth and solvent to clean tracks.
Clean outboard lower pan slot and apply Anti-
sieze to slot before reinstalling pan.
Correct or replace damaged parts and/or relubri-
cate. See Drive Chain Adjustment.
Correct or replace damaged parts and/or relu-
bricate.
Ensure T-handle release and cable assembly
operate properly. Ensure carriage can be manu-
ally extended and retracted freely.
Carriage and eccentric shaft rollers (bearings)
Lifting arm slots in rolling horizontal carriage arm
tubes
Hydraulic cylinder pivot points (4 per cylinder)
Drive chain and chain rollers
Drive chain release latch mechanism
Deploy lift, remove inboard and outboard lower
pans and blow out housing. Blow off platform
also.
Deploy lift, remove inboard and outboard lower
pans and clean housing tracks
Check drive chain tensioner, jam nuts and con
necting link for securement and/or misalignment.
Inspect drive chain release latch mechanism for
proper operation, positive securement, wear or
other damage
Inspect platform cable-activated manual release
system (T-handle/cable assembly and carriage
movement)

Page 13
Maintenance and Lubrication Schedule
+\GUDXOLF)OXLG3XPS&KHFNOHYHO1RWH)OXLG
should be changed if there is visible contamina-
tion. Inspect the hydraulic system (cylinder, hoses,
ÀWWLQJVVHDOVHWFIRUOHDNVLIÁXLGOHYHOLVORZ
Inspect lifting arm bushings and pivot pins for vis-
ible wear or damage
Inspect outer barrier pivot pin mounting bolts (2)
Mounting
Decals and Antiskid
8VHDYLDWLRQÁXLGRQO\SDUW5
&KHFNÁXLGOHYHOZLWKplatform lowered fully.
)LOOWRZLWKLQRIWKHERWWRPRIWKHÀOOWXEH
(neck).
Replace if needed.
Tighten or replace if needed
Check to see that the lift is securely anchored to
the vehicle and there are no loose bolts, broken
welds, or stress fractures.
Replace decals if worn, missing or illegible. Re-
place antiskid if worn or missing.
Repeat all previously listed inspection, lubrica-
tion and maintenance procedures at 750 cycle
intervals.
Consecutive
750 Cycle
Intervals
4500
Cycles
Inspect limit switches for securement and proper
adjustment
Inspect carriage, lifting arm and eccentric shaft
rollers (bearings) for wear or damage, positive
securement and proper operation
Inspect external snap rings (e-clips):
• Carriage roller bearings (4)
• Lower lifting arm pins (4)
• Eccentric shaft track roller bearing (1)
Inspect lower lifting arm pins for wear or damage,
positive securement and proper adjustment
Inspect eccentric shaft pins, bearing mounting
screw, washers and securement hardware for
wear or damage, positive securement and proper
operation
Inspect torque tube cams for securement, wear or
damage
Inspect housing cam brackets for securement,
wear or damage
,QVSHFWF\OLQGHUVKRVHVÀWWLQJVDQGK\GUDXOLF
connections for wear, damage or leaks
Inspect power cable
Resecure, replace or adjust as needed. See
Switch Adjustment. Correct, replace damaged
parts and/or relubricate.
Correct, replace damaged parts and/or relubricate.
Resecure, replace or correct as needed.
Resecure, replace damaged parts, lubricate or
correct as needed.
Resecure, replace damaged parts, lubricate or
correct as needed. See Carriage Ride Height
Adjustment.
Resecure, replace or correct as needed.
Resecure, replace or correct as needed.
Tighten, repair or replace if needed.
Resecure, repair or replace if needed.
1500
Cycles

Page 14
Troubleshooting Diagnosis Chart
1.00
NO
OPERATION
2.11 Hydraulic valve open
2.12 Pump mounted horizontal
2.13 No oil (low)
1.11 Low Battery
1.12 Bad ground
1.13 Poor plug connections
1.14 Blown fuse
1.15 Bad circuit breaker
1.16 Defective Interlock
Check vehicle battery
Check for good ground between vehicle chassis
and 3/8” bolt on back of power pack.
Check all plugs for proper contact.
Check fuses. Check for power on terminal 9 of
terminal block on P.C. board.
Check 20 amp self reset circuit breaker. Check
25 amp fuse from circuit breaker to P.C. board.
Check for voltage on red wire with gray stripes in
interlock plug connected to P.C. board.
FUNCTION POSSIBLE CAUSE REMEDY
2.00
PUMP RUNS
BUT WILL
NOT LIFT
PLATFORM
)OXVKYDOYHE\RSHUDWLQJPDQXDORYHUULGHVZLWFKHV
up and down at same time for 4 to 5 seconds
several times.
Power pack must be mounted vertically.
&KHFNÁXLGOHYHO
3.11 Up Solenoid
3.12 Bad power and ground
3.00
PUMP DOES
NOT RUN
WITH MANU-
AL OVERRIDE
OR REMOTE
Check for power on pump “T” wire going to solenoid.
See 1.00
Troubleshooting and
repair procedures
must be performed
DVVSHFLÀHGE\DX-
thorized service per-
sonnel only. Failure
to do so may result
in serious bodily
injury and/or property
damage.
If a problem occurs with your lift,
discontinue operation imme-
GLDWHO\'RQRW attempt repairs
yourself. Contact your dealer
or call The Braun Corporation at
7+(/,)7®. One of our
national service representatives
will direct you to an authorized
service repairman who will in-
spect your lift.
The cause of the problem can
be determined by locating the lift
function and related symptom in
the Troubleshooting Diagnosis
&KDUWV7KHVSHFLÀFFDXVHDQG
remedy can then be determined
by process of elimination. A Wir-
ing Diagram, Electrical Sche-
matic, Hydraulic Diagram and
Hydraulic Schematic are provided
to aid in troubleshooting.
A Repair Parts section with ex-
ploded views and corresponding
parts lists is also provided. Cor-
rect the problem if possible. If the
problem continues, contact The
Braun Corporation.
W
ARNING

Page 15
FUNCTION POSSIBLE CAUSE REMEDY
4.11 Barrier down LED (D29) illuminated
)XOORXW/(''QRWLOOXPLQDWHG
4.13 Remote not working properly
4.00
LIFT WILL
GO UP WITH
OVERRIDE
SWITCH BUT
NOT WITH
REMOTE
Barrier is down, barrier release pin partially out
or barrier switch out of adjustment. Make adjust-
ments as necessary.
Check full out switch for proper operation/adjust-
ment. Replace or adjust as necessary.
Check for Up LED D20 when hitting Up button on
remote. Check battery in remote. Replace bat-
tery/remote as necessary.
5.11 Hydraulic down valve bad
5.12 Dirty down valve (clogged)
5.00
LIFT WILL
NOT GO
DOWN WITH
MANUAL
OVERRIDE
OR WITH
REMOTE OR
GOES DOWN
SLOWLY
OR DRIFTS
DOWN BY
ITSELF
Check for power on valve ”T” wire going to so-
lenoid when pushing manual override or remote
button. Replace if necessary.
)OXVKYDOYHE\SXVKLQJPDQXDORYHUULGHXSDQG
down buttons at same time for 4 to 5 seconds
several times.
Troubleshooting Diagnosis Chart
6.00
LIFT WILL GO
DOWN WITH
OVERRIDE
BUT NOT WITH
REMOTE
)XOORXW/(''QRWLOOXPLQDWHG Check for proper operation of full out switch with
LED on P.C. board. Replace or adjust switch as
necessary.
7.00
LIFT WILL NOT
GO OUT WITH
OVERRIDE OR
REMOTE
7.11 Defective self-reset breaker
7.12 No power on terminal 9
7.13 Interlock circuit incomplete
7.14 Poor plug connections
7.15 Bad in/out motor
7.16 Bad power and ground
Check for power through 20 amp self-reset breaker.
Replace if necessary.
Check vehicle door full open switch and wiring.
9HULI\LQWHUORFNLQVWDOODWLRQ
Check harness connections A1, A2, B1 and B2
Check power at motor. Replace motor if necessary.
See 1.00
8.00
LIFT WILL NOT
STOW WITH
REMOTE
)DXOW\EHORZVWRZVZLWFK%HORZ
Stow LED (D24) not illuminated
8.12 Pressure LED (D18) illuminated
Check for proper operation of below stow switch.
Remove weight from platform. See Platform
Sense Calibration on page 5.

Page 16
FUNCTION POSSIBLE CAUSE REMEDY
9.00
BARRIER WILL
NOT OPERATE
UP OR DOWN
WITH REMOTE
OR OVERRIDES
9.11 Bad circuit breaker
9.12 Poor plug connections
)DXOW\EDUULHUDFWXDWRUPRWRURU
actuator out of adjustment
9.14 Bad power and ground
Check for proper operation of below stow switch.
Remove weight from platform.
Check harness connectors A1 and A2, E1, N1,
1()DQG)&KHFNSRZHUDWPRWRU$G-
just or replace actuator if necessary.
See 1.00
10.00
BARRIER
OPERATES WITH
OVERRIDES BUT
WILL NOT GO UP
WITH REMOTE
10.11 Barrier down LED (D29)
not illuminated
Check barrier down switch for proper operation
with LED on P.C. board. Replace or adjust as
necessary.
11.00
BARRIER
OPERATES WITH
OVERRIDES BUT
WILL NOT GO
DOWN WITH
REMOTE
11.11 Ground sensor LED (D23)
not illuminated
11.12 Below stow LED (D24)
not illuminated
)LOORXW/(''
not illuminated
Check ground sensor pressure transducer. Re-
place or adjust as necessary. See Ground Sense
Calibration on page 5.
Check below stow switch for proper operation.
Replace or adjust as necessary.
Check full out switch for proper operation. Re-
place or adjust as needed.
Troubleshooting Diagnosis Chart
12.00
SWITCHES
DO NOT
ACTIVATE
LED(S)
12.11 Improper terminal block wiring
12.12 No power going to switches
)DXOW\ZLULQJ
)DXOW\FRQQHFWLRQV
&KHFNWHUPLQDOEORFNIRUFRUUHFWZLULQJFRQÀJXUD-
tion.
Check power on connector A1, pins 1 and 2.
Check continuity of wires from switches to con-
nector A2.
Check for proper connections on each switch and
on each connector on the harnesses. Replace
contact if necessary. See diagram below.
13.00
DOORS
DO NOT
OPEN
)DXOW\ZLULQJ Check for proper wiring to door openers.
14.00
DOORS
DO NOT
CLOSE
)XOORXW/(''LOOXPLQDWHG
and below stow LED (D24)
not illuminated
14.12 Lift out LED (D25) illuminated
Lift is out but not below stow level.
Lift not stowed fully. Adjust lift out switch.

Page 17
CONTACT REMOVAL
1. Remove orange wedge using
needle nose pliers or a hook shaped
wire to pull wedge straight out.
2. To remove the contacts, gently pull
wire backwards, while at the same
WLPH UHOHDVLQJ WKH ORFNLQJ ÀQJHU E\
moving it away from the contact with
a screwdriver.
3. Hold the rear seal in place, as
removing the contact will displace
the seal
Troubleshooting Diagnosis Chart

Page 18
NOTES
This page intentionally left blank.