Invacare 9700 User manual

MANUAL/ELECTRIC
PORTABLE PATIENT LIFT
and SLINGS
OWNER'S
INSTALLATION AND OPERATING INSTRUCTIONS

2
SPECIAL NOTES
SPECIAL NOTES
S
P
E
C
I
A
L
N
O
T
E
S
WARNING
DO NOT OPERATE THIS EQUIPMENT WITHOUT FIRST
READING AND UNDERSTANDING THIS MANUAL. IF YOU
ARE UNABLE TO UNDERSTAND THE WARNINGS,
CAUTIONS AND INSTRUCTIONS; CONTACT A
HEALTHCARE PROFESSIONAL (DOCTOR-THERAPIST)
BEFORE ATTEMPTING TO USE THIS EQUIPMENT -
OTHERWISE INJURY OR DAMAGE MAY RESULT.
SAVE THESE INSTRUCTIONS
AND
KEEP WITH PATIENT LIFT AT ALL TIMES.
NOTICE
The information contained in this document is subject to change without
notice.
WARNING notices as used in this manual apply to hazards or unsafe
practices which could result in serious bodily harm.
CAUTION notices as used in this manual apply to hazards or unsafe
practices which could result in minor personal injury or property damage.
NOTES highlight procedures and contain information which assist the
operator in understanding the information contained in this manual.
RADIO FREQUENCY INTERFERENCE
Most electronic equipment is influenced by Radio Frequency Interference (RFI).
CAUTION should be exercised with regard to the use of portable
communication equipment in the area around such equipment. If RFI causes
erratic behavior, PUSH the EMERGENCY STOP BUTTON DOWN (ê) IMMEDI-
ATELY. DO NOT disengage the Emergency Stop Button while transmission is in
progress.
MAINTENANCE
Maintenance MUST be performed ONLY by qualified personnel.

3
TABLE OF CONTENTS
SPECIAL NOTES ............................................. 2
SAFETY SUMMARY......................................... 4
SPECIFICATIONS ............................................ 5
FEATURES ....................................................... 6
HANDLING PROCEDURES ............................. 8
Shipping and Transportation Instructions ......... 8
Unpacking ....................................................... 8
Inspection........................................................ 8
Storage............................................................ 8
ASSEMBLY....................................................... 9
Assembly of the Patient Lift .............................. 9
Unpacking the Patient Lift ............................... 9
Assembling the Mast to the Base ................... 9
Assembling the Manual/Hydraulic Pump to
the Boom.................................................... 10
Assembling the Electric Actuator to the
Boom.......................................................... 10
Shifter Handle Installation ............................. 11
CONVERSION FROM A MANUAL TO AN
ELECTRIC LIFT......................................... 12
Disassembly/Assembly ................................... 12
Removing the Manual/Hydraulic Pump
Assembly.................................................... 12
Assembly of the Electric Actuator ................. 12
Attaching the Control Box to the Mast .......... 13
Battery Charging ........................................... 13
ONE-PIECE CONTOUR SLINGS................... 15
Model No. 9746 Hammock and Model No.
9747 Hammock w/Commode Opening ......... 15
Fabric ............................................................ 15
Body ............................................................. 15
Positioning the Model No. 9746 Hammock or
Model No. 9747 Hammock w/Commode
Opening......................................................... 16
Positioning the Patient on the Sling with or
without Commode Opening .......................... 16
MODEL NO. 9742 UNIVERSAL DELUXE
SLING ............................................................ 18
Positioning the Patient in the Model No. 9742
Universal Deluxe Sling .................................. 18
OPERATION ................................................... 20
Operating the Patient Lift ................................ 20
To Close/Open the Legs of the Base
Assembly.................................................... 20
Raising/Lowering Manual/Hydraulic Lift ........ 20
Raising the Lift ........................................... 20
Lowering the Lift......................................... 21
T
A
B
L
E
O
F
C
O
N
T
E
N
T
S
OPERATION (Cont.)
Raising/Lowering Electric Lift........................ 21
Raising the Lift ........................................... 21
Lowering the Lift......................................... 21
LIFTING THE PATIENT .................................. 22
Attaching the Slings to the Patient Lift ............ 22
Lifting/Moving the Patient................................ 23
TRANSFERRING PATIENT FOR USE OF
THE BATHROOM FACILITIES .................. 25
Transferring Patient for Use of a Commode
Chair or Standard Commode ..................... 25
Transferring to a Commode Chair ................ 25
Transferring to a Standard Commode .......... 26
Transferring to a Bathing Unit......................... 26
TRANSFERRING TO A WHEELCHAIR ......... 27
TRANSFERRING FROM A WHEELCHAIR
TO A CAR .................................................. 28
TRANSFERRING FROM A CAR TO A
WHEELCHAIR .............................................. 30
TROUBLESHOOTING.................................... 31
MAINTENANCE SAFETY INSPECTION
CHECKLIST.................................................. 32
CARE AND MAINTENANCE OF YOUR
PATIENT LIFT ............................................ 33
Lubrication..................................................... 33
Wear and Damage........................................ 33
Cleaning ........................................................ 33
Manual/Hydraulic Pump ................................ 34
Manual/Hydraulic Pump or Electric
Actuator Replacement............................. 34
Swivel Bar Replacement ............................... 35
Base Adjustment ........................................... 35
Shifter Handle Adjustment ............................ 36
Casters.......................................................... 36
Rear Caster Replacement.......................... 36
Front Caster Replacement ......................... 36
Front Caster Housing Removal.................. 36
ACCESSORIES .............................................. 37
Invacare 9833A Weight Module
(Digital Scale)............................................. 37
LIMITED WARRANTY .................................... 39
TABLE OF CONTENTS

4
SAFETY SUMMARY
SAFETY SUMMARY
WARNING
Check all parts for shipping damage before using. In case of damage, DO NOT use the equipment. Contact the
Dealer for further instructions.
The Invacare patient lift is NOT a transport device. It is intended to transfer an individual from one resting
surface to another (such as a bed to a wheelchair). Moving a person suspended in a sling over ANY distance
is NOT recommended.
DO NOT attempt any transfer without approval of the patient’s physician, nurse or medical assistant.
Thoroughly read the instructions in this Owner’s Manual, observe a trained team of experts perform the lifting
procedures and then perform the entire lift procedure several times with proper supervision and a capable
individual acting as a patient.
Usecommon sense inall lifts. Special careMUST BE takenwith people withdisabilities who cannot cooperate
while being lifted. Use restraint straps if necessary.
Invacare slings and patient lift accessories are specifically designed to be used in conjunction with Invacare
patient lifts. Slings and accessories designed by other manufacturers are not to be utilized as a component of
Invacare’s patient lift system. Use of these products is prohibited and will void Invacare’s patient lift warranty.
Use only genuine Invacare slings and lift accessories to maintain patient safety and product utility.
Use a sling that is recommended by the individual’s doctor, nurse or medical assistant for the comfort and
safety of the individual being lifted.
DO NOT use any kind of plastic back incontinence pad or seating cushion between the patient and sling
material that may cause the patient to slide out of the sling during transferring.
When using an adjustable base lift, the legs MUST BE in the maximum OPENED/LOCKED position BEFORE
lifting the patient.
Before transferring a patient from a stationary object (wheelchair, commode or bed), slightly raise the patient
offthe stationary objectand check that all sling attachments aresecure. If any attachmentis not correct, lower
the patient and correct the problem, then raise the patient and check again.
Duringtransfer,withpatient suspendedin a sling attached to the lift, DO NOTroll casterbase overobjects such
as carpet, raised carpet bindings, door frames, or any uneven surfaces or obstacles that would create an
imbalanceof the patientlift and could cause the patient liftto tip over. Use steering handles on the mastat ALL
times to push or pull the patient lift.
Invacare does NOT recommend locking of the rear casters of the patient lift when lifting an individual.
Doing so could cause the lift to tip and endanger the patient and assistants. Invacare DOES recommend
that the rear casters be left UNLOCKED during lifting procedures to allow the patient lift to stabilize itself
when the patient is initially lifted from a chair, bed or any stationary object.
After the first 12 months of operation, inspect the swivel bar and the eye of the boom (to which it attaches) for
wear. If the metal is worn, the parts MUST be replaced. Make this inspection every three (3) months thereafter.
The hydraulic/electric pump is sealed at the factory and if service is required, the pump unit MUST BE returned
to the factory for repair. DO NOT attempt to open the hydraulic/electric pump or obtain local service as this will
VOID the warranty and may result in damage and a costly repair. Consult your Dealer or Invacare for further
information.
Casters and axle bolts require inspection every six (6) months to check for tightness and wear.
Regular maintenance of patient lifts and accessories is necessary to assure proper operation.
DO NOT exceed maximum weight limitation of the patient lift. The suggested weight limitation will vary from
300 lbs. for the Electric Lift to 375 lbs. for the Manual (Hydraulic) Lift depending on the type of patient lift
purchased.
S
A
F
E
T
Y
S
U
M
M
A
R
Y

5
SPECIFICATIONS
SPECIFICATIONS
9700
Manual / Hydraulic
S
P
E
C
I
F
I
C
A
T
I
O
N
S
9701
Electric
Height at Sling Hook-up- MAX.:
Height at Sling Hook-up- MIN.:
Base Width OPEN:
Base Width CLOSED:
Base Height (Clearance):
Base Length:
Caster Size (FRONT/REAR):
Folded Height:
Sling Options:
Weight Capacity:
Weight IN Carton:
Weight OUT of Carton:
Battery:
Charger Input:
Charger Output:
Accessories:
Audible Low Battery Alarm:
Motor Safety Devices:
* Approx. Lifts per Charge:
Warranty Pump/Electronics:
67.5-inches
18.5-inches
42.0-inches
24.5-inches
3.5-inches
42.0-inches
2.0-inches/5.0-inches
16.5-inches
3-Styles
375 lbs.
96 lbs.
78 lbs.
N/A
N/A
N/A
Digital Scale, Quick Fold Kit
N/A
N/A
N/A
1 Year
66-inches
17-inches
42.0-inches
24.5-inches
3.5-inches
42.0-inches
2.0-inches/5.0-inches
16.5-inches
3-Styles
300 lbs.
92 lbs.
79 lbs.
2-12V Rechargeable Sealed
120V AC
24V DC
Digital Scale, Quick Fold Kit
When Recharging Needed
Automatic Stop Button
60 to 100
1 Year
NOTE: 9700K Electric Conversion Kit has the same specifications as 9701. Kit includes actuator, battery with
bracket, remote control unit, recharging unit and attachment hardware.
* Varies dependent upon load and stroke.
9742 9746 9747
SLINGS Universal Deluxe Hammock Hammock
Padded w/Commode
Overall Length: 25-inches Back 50-inches 50-inches
27-inches Leg
Overall Width: 41-inches 40-inches 40-inches
Commode Opening: N/A N/A 6-inches Wide x 12-inches Long
Accessories: 9732 Digital Scale Bracket ONLY.
9770 Easy-Store Kit (Pin and Ring Assembly for quickly Disassembling Lift WITHOUT Tools).

6
FEATURES
FEATURES
MANUAL / HYDRAULIC LIFT (FIGURE 1)
Manual / Hydraulic weight limitation is 375 lbs.
Mast bolts into base. Can be separated for storage.
Operation optimizes lift capabilities. Requires less
physical effort for raising patient.
Offset mast and boom style provides better lift path.
Maximizes full travel range.
Pump handle can rotate from side-to-side for
convenience of assistant.
Range: 49.0 - inches of range allows the patient to
be picked up from a lying position on floor.
ELECTRIC LIFT (FIGURE 2)
Electric lift weight limitation is 300 lbs.
Mast bolts into base. Can be separated for storage.
Operation optimizes lift capabilities. Requires less
physical effort for raising patient.
Offset mast and boom style provides better lift path.
Maximizes full travel range.
Hand control with elongated cord for convenience
of assistant.
Range: 49.0 - inches of range allows the patient to
be picked up from a lying position on floor.
F
E
A
T
U
R
E
S
Sling Sold
Separately
Castered Base
Boom
Swivel Bar
Hydraulic
Pump
Pump
Handle
FIGURE 2 - ELECTRIC LIFT
Boom
Electric Actuator
Hand
Control
Mast
FIGURE 1 - MANUAL/HYDRAULIC LIFT
Mast
Control
Valve
Shifter
Handle
Control
Box
Shifter
Handle
Castered Base
Swivel
Bar

7
FEATURES
FEATURES (Cont.)
PATIENT SLINGS
WARNING
Use a sling that is recommended by the
individual’s doctor, nurse or medical assistant
for the comfort and safety of the individual
being lifted.
Patient slings work in conjunction with lifts to
support the patient during lifting and transferring
procedures.
Slings attach to the lift by using the sewn-in
hook-on points. Slings are adjustable.
Each sling offers reinforcing at each hook-on point
to ensure patient safety.
Eachsling isconstructed ofdurable materialswhich
resist deterioration from exposure to moisture or
laundering.
Model No. 9746 Hammock and Model No. 9747
Hammock w/Commode Opening (FIGURE 3)
NOTE: Both slings have a headrest.
The one-piece contour slings can be used on heavy
or light patients. Supports patient from head to the
knees. Used for weighing, transferring or to simplify
the use of restroom facilities.
Model No. 9742 Universal Deluxe Sling
(FIGURE 4) F
E
A
T
U
R
E
S
Model No. 9746 Model No. 9747
FIGURE 3 - MODEL NO. 9746 HAMMOCK AND
MODEL NO. 9747 HAMMOCK w/COMMODE
OPENING SLINGS
FIGURE 4 - MODEL NO. 9742 UNIVERSAL
DELUXE SLING
ACCESSORIES
Model 9833 Weight Module (Digital Scale)
and Adapter Bracket
375 lbs. Capacity
Accurate within 0.25 grams
Measures 4.5-inches (Height)
NOTE: Refer to Accessories Section in the back
of this manual for correct operation of the Model
9833 Digital Scale.
Divided leg design is best suited for high level
spinal cord injuries or patients which sling removal
ismore difficult.Support rangesfrom theupperback
to beneath the thighs. Can be positioned with
patientseated. Greatlysimplifies theuseof restroom
facilities.

8
HANDLING PROCEDURES
SHIPPING AND TRANSPORTATION
INSTRUCTIONS (FIGURE 1)
If the Patient Lift is to be reshipped by common
carrier, it should be packed in the same carton.
Extra cartons are available from Invacare.
Unpacking
1. Check for any obvious damage to the carton or
its contents. If damage is evident, notify your
Invacare Dealer/Carrier.
2. Remove all loose packing from the carton.
3. Carefully remove all the components from the
carton.
NOTE: Unless the Patient Lift is to be used
immediately, retain boxes, containers and
packing material for use in storing until use of
the patient lift is required.
Inspection
1. Examine exterior of the Patient Lift for nicks,
dents, scratches or damages. Inspect all
components.
Storage
1. Store the packaged Patient Lift in a dry area.
2. DO NOT place other objects on top of the
packaged Patient Lift.
HANDLING PROCEDURES
H
A
N
D
L
I
N
G
P
R
O
C
E
D
U
R
E
S
FIGURE 1 - SHIPPING AND TRANSPORTATION

9
ASSEMBLY
ASSEMBLY OF THE PATIENT LIFT
WARNING
Use ONLY Invacare parts in the assembly of this
patient lift. The base legs, the mast, boom, pump
assembly and the swivel bar are manufactured to
specifications that assure correct alignment of all
parts for safe functional operation.
ASSEMBLY
FIGURE 4 - SECURING MAST TO BASE
1. Unpack the components from the shipping carton.
2. Cut the tie-wraps that secure swivel bar to the base
and the pump assembly to the mast (FIGURE 1).
Unpacking the Patient Lift
A
S
S
E
M
B
L
Y
Adjustment
Knob U-shaped
cut-outs
Mast
Bushing
WARNING
The mast may be removed from the base for
storage or transporting. Each time the mast is
removed and returned to the base, the mast MUST
be properly secured to the base assembly.
3. Position the mast bushings into the U-shaped
cut-out of the base while pushing the mast into an
upright position (FIGURE 4).
4. Insert pivot bolt with washers through the base and
mast bushing. Secure with nut (FIGURE 4).
5. Align adjustment knob flush with the lip of the
U-shaped cut-out of the base (FIGURE 4).
NOTE: This will prevent the mast from
disengaging from the base.
Tie-Wrap
FIGURE 1 - UNPACKING THE PATIENT LIFT
Assembling the Mast to the Base
1. Lock casters (FIGURE 2).
FIGURE 2 - LOCKING THE CASTERS
2. Remove the covers, pivot bolt, nut and washers,
located at the base of the mast (FIGURE 3).
FIGURE 3 - REMOVING PIVOT BOLT
NOTE: The connection between the mast and the
base should be cleaned and coated with
petroleum jelly prior to assembly.
LOCK UNLOCK

10
ASSEMBLY (Cont.)
ASSEMBLY
Assembling the Manual / Hydraulic Pump
to the Boom (FIGURE 5)
1. Remove the covers, bolt, and nut from the
mounting bracket on the boom assembly.
2. Unpack the plastic bushing from the patient lift
carton.
3. Lift-up on the boom and place it on your left
shoulder.
4. Let the hydraulic pump rest on the right-side of
your chest and rotate the shaft extension of the
hydraulic pump assembly until it lines-up with
the mounting bracket holes in the boom
assembly.
5. Turn the plastic bushing 90o and place over the
shaft extension of the hydraulic pump.
Plastic Bushing
NOTE: Turn 90o.
A
S
S
E
M
B
L
Y
WARNING
There are two (2) silver plugs in the mounting
holes next to the hydraulic pump mounting
bracket on the boom. DO NOT remove these
silver plugs and use these holes at anytime or
injury to the patient and/or assistant may
occur (FIGURE 5).
6. Align the holes of the boom assembly mounting
bracket with those of the hydraulic pump and
insert the bolt. Secure with nut.
NOTE: Be sure that the bolt is completely
through the holes of the boom assembly
mounting bracket and the manual / hydraulic
pump assembly. The boom assembly will pivot
easily if the mounting hardware is aligned
properly when the boom assembly is secured
to the mast. CAUTION
DO NOT overtighten the nut and bolt and bend
the mounting bracket.
Mounting
Bracket
FIGURE 5 - ASSEMBLING THE MANUAL / HYDRAULIC PUMP TO THE BOOM
Assembling the Electric Actuator to the
Boom (FIGURE 6)
1. Remove the covers, bolt, and nut from the
mounting bracket on the boom assembly.
2. Unpack the plastic bushing from the patient lift
carton.
3. Lift-up on the boom and place it on your left
shoulder.
NOTE: The bottom of the electric actuator
assembly will already be assembled to the mast
mounting bracket.
4. Let the actuator rest on your right-side of your
chest and rotate the shaft extension of the
actuatorassemblyuntil itlines-up withthe mount-
ing holes in the boom assembly.
5. Place the plastic bushing over the shaft
extension of the actuator.
WARNING
DO NOT use for
mounting.
Mounting
Bracket

11
ASSEMBLY (Cont.)
ASSEMBLY
A
S
S
E
M
B
L
Y
WARNING
There are two (2) silver plugs in the mounting
holes next to the actuator mounting bracket on
the boom. DO NOT remove these silver plugs
and use these holes at anytime or injury to the
patient and/or assistant may occur (FIGURE 6).
6. Align the holes of the boom assembly mounting
bracket with those of the actuator and insert the
bolt. Secure with nut.
NOTE: Be sure that the bolt is completely
through the holes of the boom assembly
mounting bracket and the actuator assembly.
The boom assembly will pivot easily if the
mounting hardware is aligned properly when the
boom assembly is secured to the mast.
CAUTION
DO NOT overtighten the nut and bolt and bend
the mounting bracket.
WARNING
DO NOT use for
mounting.
Mounting
Bracket
Plastic Bushing
Actuator
Assembly
NOTE: The bottom of the actuator assembly
will already be assembled to the mast mounting
bracket.
FIGURE 6 - ASSEMBLING THE ELECTRIC ACTUATOR TO THE BOOM
Shifter Handle Installation (FIGURE 7)
1. Remove the shifter handle from the packaging
carton.
2. Press down on the release button on the shifter
handle mounting tube and insert the shifter
handle over the release button until the shifter
handlelocks inplace.(Button MUSTbe protrud-
ing from the opening in the shifter handle
(FIGURE 7).
FIGURE 7 - SHIFTER HANDLE INSTALLATION
Release Button
Shifter Handle

12
CONVERSION FROM A MANUAL TO AN ELECTRIC LIFT
CONVERSION FROM A MANUAL TO AN ELECTRIC LIFT
4. Place the plastic bushing over the shaft
extension of the electric actuator.
C
O
N
V
E
R
S
I
O
N
Assembly of the Electric Actuator (FIGURE 2)
DISASSEMBLY / ASSEMBLY
Removing the Manual / Hydraulic Pump
Assembly (FIGURE 1)
1. Raise the lift so the boom is resting on your left
shoulder.
2. Remove the covers, bolt, nut and plastic bush-
ing from the hydraulic pump mounting bracket
on the boom assembly.
3. Lower theboomand pumpassemblies untilthey
rest on the floor.
4. Remove the covers, bolt, nut, washers and
spacer from the mounting bracket on the mast
assembly.
FIGURE 1 - REMOVING THE MANUAL /
HYDRAULICPUMP ASSEMBLY
1. With the boom resting on the ground, attach the
bottompart ofthe actuatorassembly tothe mast
mounting bracket using bolt, washers, spacer,
nut and covers.
2. Lift-up on the boom and place it on your left
shoulder.
3. Let the actuator rest on the right-side of your
chest and rotate the shaft extension of the
actuator assembly until it lines-up with the
mounting bracket holes in the boom assembly.
Boom
Mast
WARNING
There are two (2) silver plugs in the mounting
holes next to the electric actuator mounting
bracket on the boom. DO NOT remove these
silver plugs and use these holes at anytime or
injury to the patient and/or assistant may
occur (FIGURE 2).
WARNING
DO NOT use for
mounting.
Boom
Mast
Plastic
Bushing
CAUTION
DO NOT overtighten the nut and bolt and bend
the mounting bracket.
5. Align the holes of the boom assembly mounting
bracket with those of the electric actuator and
insert the bolt. Secure with nut.
NOTE: Be sure that the bolt is completely
through the holes of the boom assembly
mounting bracket and the actuator assembly.
The boom assembly will pivot easily if the
mounting hardware is aligned properly when the
boom assembly is secured to the mast.
FIGURE 2 - ASSEMBLY OF THE ELECTRIC
ACTUATOR
Plastic
Bushing

13
Attaching the Control Box to the Mast
(FIGURE 3)
NOTE:Whenpositioningthecontrolboxonthemast,
make sure there is enough clearance between the
Emergency Stop Button and the bottom of the
steering handle to be able toengage and disengage
the Emergency Stop Button.
CONVERSION FROM A MANUAL TO AN ELECTRIC LIFT
CONVERSION FROM A MANUAL TO AN ELECTRIC LIFT
FIGURE 3 - ATTACHING THE CONTROL BOX
TO THE MAST
Emergency
Stop Button
Steering
Handle
C
O
N
V
E
R
S
I
O
N
CAUTION
It is important to ensure that both input and
output plugs are correctly inserted before
connection of power. If the patient lift is
charged with any other type of charger, it is
possible to irreparably damage the batteries.
FIGURE 4 - DISENGAGING THE EMERGENCY
STOP BUTTON
Disengage
(Rotate
Clockwise)
Engage
(Push Down)
Emergency
Stop Button
The charger automatically stops charging when the
batteries are fully charged; therefore, it is perfectly
safe to leave the patient lift on charge whenever it
is not being used to ensure peak performance.
Battery Charging
WARNING
NEVER use or move the patient lift while
battery is being charged.
NOTE: Ensure batteries are regularly charged,
preferably EVERY NIGHT. This will prolong their
life and maintain peak performance.
The battery charger is fully automatic and can be
connected to the lift at any time, OTHER THAN WHEN
LIFT IS IN USE. It is recommended that the lift charging
take place in a well ventilated dry room. This should be
EVERY NIGHT and/or when the audible alarm sounds
duringoperation.Thebatterychargerhasaroundoutput
plug which is plugged into the patient lift hand-control.
TheRED emergencystop button,mounted onthe topof
control box MUST be DISENGAGED (rotated
CLOCKWISE until fully out) during charging (FIGURE
4).
From Electric Actuator
From Hand
Control
1. Standing behind the lift, hold the control box
against the right-side of the mast.
2. Place theU-boltsaround theleft-sideof themast
and through the control box mounting holes.
3. Secure with washers and nuts.
4. Plugthecables fromthe actuatorassemblyand
hand control into the control box.

14
NOTES
NOTES
N
O
T
E
S

15
ONE- PIECE CONTOUR SLINGS
MODEL NO. 9746 - HAMMOCK AND
MODEL NO. 9747 - HAMMOCK W/COMMODE
OPENING (FIGURE 1)
Invacareslings aredesignedspecifically forusewith
Invacare Patient Lifts and made to support the
patient during lift and transfer procedures. Slings
attach to the lift with color coded straps for easy
positioning. The slings are reinforced at all points
of attachment for safety. The fabrics used in these
slings are of very durable materials that resist
deterioration from exposure to moisture and
laundering. This design will accommodate patients
of heavy or light weight with full support from the
head to the knees. It is particularly good for users
with only moderate upper body strength, for
bathing or for those remaining in the sling for
extended periods of time.
Fabric
The outer side has a reinforced "grab handle" for
assistancein positioningthe patientin awheelchair,
commode, etc. The edging is soft yet durable with
extra reinforced stitching for safety.
ONE-PIECE CONTOUR SLINGS
C
O
N
T
O
U
R
S
L
I
N
G
S
Model No. 9746 Model No. 9747
Body
Slings may be ordered at the time of purchase with
a commode opening in the seat section for use over
a toilet or a commode chair. Slings are constructed
with a high back section that provides additional
support for the head and neck.
FIGURE 1 - MODEL NO. 9746 HAMMOCK AND
MODEL NO. 9747 HAMMOCK w/COMMODE
OPENING SLINGS
NOTE: Always place the sling under the patient
with the handle away from the patient.
NOTE: Laundering should always be done with
dark colors. Refer to tagged washing
instructions on the sling.
Open mesh polyester fabric is an exceptional
material that provides safety and comfort for the
patient. The open mesh weave of the fabric is dyed
blue or teal, preshrunk, and durable for use and
laundering. It provides considerable traction to
resist slipping and sliding during use.

16
ONE-PIECE CONTOUR SLINGS (Cont.)
3. The topedgeof theslingfabricshouldbe slightly
above the patient's head.
4. The bottom edge of the sling fabric should then
be a few inches above the back of the patient’s
knees.
NOTE: Invacare recommends that two (2)
assistants (One [1] on each side of the bed) be
used when positioning the patient on a sling.
The bed rails may also be raised to minimize
patient movement.
5. With one (1) assistant holding the patient, the
second assistant pushes the folded sling under
the patient without rolling him/her over.
Positioning the Patient on the Sling with or
without Commode Opening
NOTE: Use the following method to easily move
the patient and avoid strain to yourself.
1. If the patient is to roll to their LEFT-SIDE, then
elevatethe patient’sRIGHT KNEEuntil theright
foot is flat on the bed (FIGURE 3).
FIGURE 3 - ROLLING PATIENT ONTO
HIS/HER SIDE
Positioning the Model No. 9746 Hammock
or Model No. 9747 Hammock w/Commode
Opening (FIGURE 2)
ONE-PIECE CONTOUR SLINGS
C
O
N
T
O
U
R
S
L
I
N
G
S
FIGURE 2 - POSITIONING THE SLING
1. Position the patient in the center of the bed and
laying flat on his/her back.
2. Fold the sling in half (length-wise) and place the
sling beside the patient.
NOTE: The closed-end or commode opening of
the sling with positioning handle should be
facing the patient when folded.
Top Edge of
Sling
Commode
Opening
Positioning
Handle
Bottom Edge
of Sling
Sling
Hooks
Sling
Hooks

17
FIGURE 4 - ROLLING PATIENT ONTO HIS/HER
OPPOSITE SIDE AND BACK
ONE-PIECE CONTOUR SLINGS (Cont.)
NOTE: Invacare recommends that two (2)
assistants (One [1] on each side of the bed) be
used when positioning the patient onto a sling.
2. With an assistant on each side of the bed and up
againstthemattress,theassistantontheleft-hand
side of the bed will position his/her RIGHT-HAND
on the elevated KNEE and his/her LEFT-HAND
under the patient’s RIGHT SHOULDER, slowly
push on the knee and assist with a slight lift of the
shoulder. The patient will easily roll onto their side
(FIGURE 3).
3. With the patient on their side, push the fabrics
of the seat and back gently under them
(FIGURE 3).
NOTE: The patient’s head should be positioned
in the headrest just below the top edge for
maximum comfort and the lower edge of the seat
section positioned a few inches above the back
of the patient’s knees (FIGURE 2).
4. Roll the patient on to his/her back (FIGURE 4).
NOTE: Assistants will reverse roles.
5. After thepatienthas beenpositioned onceagain
on his/her back, you now need to roll the patient
totheir RIGHT-SIDE(facing theassistant onthe
LEFT).
6. With an assistant on each side of the bed and
up against the mattress, the assistant on the
right-hand side of the bed will elevate the LEFT
KNEE and position his/her LEFT-HAND on the
elevated KNEE and his/her RIGHT-HAND
under the patient’s LEFT SHOULDER, slowly
push on the knee and assist with a slight lift of
the shoulder and the patient will easily roll onto
their side (FIGURE 4).
7. Pull the fabrics of the seat and back across the
mattress until they are smooth (FIGURE 4).
8. Roll the patient onto their back and they should
be approximately centered on the sling section
(FIGURE 4).
9. Attach the sling to the hooks of the swivel bar.
Refer to Attaching the Slings to the Patient
Lift in LIFTING THE PATIENT Section of this
manual.
ONE-PIECE CONTOUR SLINGS
C
O
N
T
O
U
R
S
L
I
N
G
S

18
UNIVERSAL DELUXE SLING
MODEL NO. 9742 -UNIVERSAL DELUXE
SLING (FIGURES 1A and 1B)
FIGURE 1A - POSITIONING THE PATIENT IN
THE MODEL NO. 9742 - UNIVERSAL DELUXE
SLING
UNIVERSAL DELUXE SLING
U
N
I
V
E
R
S
A
L
D
E
L
U
X
E
S
L
I
N
G
Positioning the Patient in the
Model No. 9742 Universal Deluxe Sling
NOTE: Headrest is not available on the Model
No. 9742 Universal Deluxe Sling.
NOTE: Invacare recommends that two (2)
assistants (one [1] in front and one [1] in back
of the wheelchair) be used when positioning the
patient in the universal deluxe sling.
NOTE: Use the following method to easily move
the patient and avoid strain to yourself.
WARNING
If the patient is in a wheelchair, secure the wheel
locks in place to prevent the chair from moving
forward or backwards.
1. The rear wheel locks of the wheelchair are locked
to prevent movement of the chair.
2. With the patient sitting in a chair one (1)
assistant in the front and the other assistant in
the back, lean the patient forward.
NOTE: The front assistant will be supporting the
weight of the patient.
3. Place the universal deluxe sling behind the
patient (with "grab handle" on the outside) and
bring the flaps out alongside the patient’s legs.
NOTE: The back of the universal deluxe sling
should be parallel to the patient’s upper arms
and be positioned between the top of the
patient’s back and the top of the chair back.
4. With the back of the sling positioned properly,
push the edges of the commode opening under
the patient’s buttocks.
5. Lean the patient back into the chair with the
assistant in the rear supporting his/her weight.
6. Lift the patient’s legs (one at a time) and reach
under the patient’s leg and pull until the front of
the sling is behind the patient’s knees (about
three [3] inches) and the back of the sling
remains in position.
NOTE: The straps may be crossed BETWEEN
or UNDERNEATH the patient's legs.
7. Attach the sling to the swivel bar. Refer to
Attaching the Slings to the Patient Lift in
LIFTING THE PATIENT Section of this manual.

19
UNIVERSAL DELUXE SLING (Cont.)
FIGURE 1B - POSITIONING THE PATIENT IN THE MODEL NO. 9742 - UNIVERSAL DELUXE SLING
U
N
I
V
E
R
S
A
L
D
E
L
U
X
E
S
L
I
N
G
UNIVERSAL DELUXE SLING
Between Underneath

20
OPERATION
OPERATING THE PATIENT LIFT (FIGURE 1)
OPERATION
O
P
E
R
A
T
I
O
N
To Close/Open the Legs of the Base Assembly
Theshifterhandleisusedtoopenorclosethe legsofthe
base for stability when lifting a patient.
WARNING
The operation of the patient lift is an easy and safe
procedure. DO NOT attempt any transfer without
approval of the patient’s physician, nurse or
medicalassistant.Thoroughlyreadtheinstructions
in this Owner’s Manual, observe a trained team of
experts performing the lifting procedures and then
perform the entire lift procedure several times with
proper supervision and a capable individual acting
as a patient.
ONLY operate this lift with the legs in MAXIMUM
OPEN POSITION and LOCKED in place. The base
legsMUSTbelockedintheopenpositionatalltimes
for stability and patient safety when lifting and
transferring a patient.
1. Standattherearofthepatientliftandgraspthe shifter
handlewithone(1)handandplacetheoppositehand
on the steering handle of the mast for balance.
There are two (2) controls on the pump
assembly:
a. The control valve
b. The pump handle
RAISING THE LIFT (FIGURE 2). The controlvalve
MUST be in the closed position (turn control valve
clockwise until tight) to move the pump handle up
and down and elevate the boom and the patient.
Raising/Lowering Manual/Hydraulic Lift
WARNING
Invacare does NOT recommend locking of the
rear casters of the patient lift when lifting an
individual. Doing so could cause the lift to tip
and endanger the patient and assistants.
Invacare DOES recommend that the rear
casters be left UNLOCKED during lifting
procedures to allow the patient lift to stabilize
itself when the patient is initially lifted from a
chair, bed or any stationary object.
FIGURE 1- TO CLOSE/OPEN THE LEGS OF THE
BASEASSEMBLY
NOTE: The shifter handle MUST lock into its
mounting slot to lock the legs in the full open
or closes position.
WARNING
If the shifter handle is NOT positioned
completely into its mounting slot, DO NOT use
the patient lift until shifter handle is properly
seated and the legs of the patient lift LOCKED
in place or injury and/or damage may occur.
TO CLOSE.
2. Push the shifter handle OUT and away from the
patientliftandthentoyourLEFTuntilitLOCKSinthe
notch of the bracket.
TO OPEN.
3. Push the shifter handle OUT and away from the
patient lift and then to your RIGHT until it LOCKS in
the notch of the bracket.
TO OPEN
TO CLOSE