Braun Group XTR202-SFP User manual

XTR202-SFP
1. 100M Multi-Port Media Converter
1.1. Brief Introduction
Thanks for purchasing Multi-Port 100M optical transceiver! This product
supports IEEE802. Z/AB 100Base-SX/LX protocol, the working mode of
duplex full mode and half mode. The electric interface is the rate of 10M and
100M as well as the through line and cross wire. This manual is for various
models of optical transceivers.
1.2. Packing list
Please check the following items in the package before installing the
converter.
Media converter 1piece
AC/DC adapter (external) 1piece
User manual 1copy
Please contact the dealer immediately for any missing or damaged items.
1.3. Installation
（1）. Interface
RJ-4 interface
The transmission media is CAT5 twisted-pair with a maximum length of 100
meters. It features auto -negotiation of straight through line and crossover
cables.
Fiber interface
The SC or LC fiber interface is of duplex type, namely TX and RX. When
the two sets of optical transceiver are interfaced or connected to switch with
fiber interface, the fiber is in cross connection, namely "TX-RX", "RX-TX"
(direct butting for single optical fiber).

XTR202-SFP
（2）. Connection
Connect the network device (work station, hub or switch) to the RJ-45
jack of the optical transceiver through twisted-pair CAT5. Connect the multi-
mode /single mode fiber to SC/LC fiber interface of the optical transceiver.
Turn the power on. The corresponding LED is on for a correct connection.
(See the table below for the LED indicator lamp)
1.4. LED indicators
The LED indicator lamps serve as device monitoring and error display.
The following explains each LED indicator.
LED Status Function
SFP1
/SFP2
On “Connection status display for fiber link.
“ON” indicates that Fiber link is in correct connection.
Blink Active status display of fiber link
“Blink” indicates packet goes through Fx end.
TP Link/Act On Connection status display for electric link.
“ON” indicates that electric link is in correct connection.
Blink Active status display of electric link
“Blink” indicates packet goes through Tx end.
100 On Transfer rate of electric interface is 1000Mbps.
Off Transfer rate of electric interface is 10Mbps.
PWR On Power is on and normal.

XTR202-SFP
1. . Main features
1. Conforms to IEEE802. Z/AB 100 Base-T/SX/LX standard
2. Back pressure flow control for full duplex IEEE802. X and half duplex.
. Automatic identification of MDI/MDI-X cross line.
4. Conforms to safety code of FCC and 15 CLASS A, CE.
1.6. Technical parameters
(1) Standard Protocol: IEEE802. Z/AB 1000Base-T/SX/LX standard
(2) Transfer rate: electric interface: 10/100Mbps
Optical interface: 125 Mbps
( ) Connectors: TX: UTP RJ-45 connector
FX: SFP Slot
(4) Operation mode: full duplex mode or half duplex mode
(5) Power supply parameter:
External: 110-265V AC 48VDC
Internal: 5V DC 2A
(6) Operating temperature: -10~55 ℃
(7) Relative humidity: 5%-90%
(8) Twisted Pair cable: Cat5 UTP cable
(9) Fiber cable:
Multi-mode: 50/125, 62.5/125
Single mode: 8. /125, 8.7/125, 9/125 or 10/125μm
(10) Outside dimensions:
125mm (W) * 8 mm (D) * 26 mm (H) (Internal power supply)
2. Warning
1. This product is suitable for indoor application.
2. Place the dust cover on the fiber interface when not in use.
. It is dangerous to stare at the fiber transmitter with the naked eye.
4. Optical fiber transceivers must be used in pair.
5. Single optical fiber transceiver must be used in pair(A,B)
A: TX1 10RX1550nm B: TX1550/RX1 10nm.
3. Trouble shooting
1. Device is not connecting. Please check that the corresponding network
device is using the same transfer rate as the media converter (10Mbps,
100Mbps or 1000Mbps).

XTR202-SFP
2. If power loss is excessive in the fiber, please check and clean the fiber
patch cord connectors.
4. Responsibility Note
(1) The user should cover the damage during transport to equipment resend
for maintained at the user’s own expense
(2) Please contact your authorized reseller immediately, if there is any
damage to the equipment during transport
( ) If you want to prepare power supply by yourself, please make sure the
power supply you select meet the requirement given by this manual. We
will not cover the damage caused by your using unqualified power supply.
(4) Do please follow this manual when using the power supply.
(5) All rights reserved. No part of this manual can be reproduced, or
transmitted in any form or by any means, without authorization form us.
(6) We will not cover the damage to the equipment or any person caused by
your changing the equipment or this manual in any form without
authorization from us.
(7) We will change the equipment for new ones if it can not work normally
because of the quality itself within the warranty time. We will keep the old
ones.
(8) The packages of the equipment meet the requests of environmental
protection, should be recycled.
Attention: If there are any printing mistakes in this manual, the right to explain
is reserved. And the pictures of equipment appearance in this manual are just
for user’s information, the final equipment appearance depends on reality
products, if there are any improvements on technology, we will be sorry for
won’t inform you again.