BRC Alta Instruction Manual

BRC Group | 24 Armstrong Ave, Georgetown, ON L7G4R9 | 877-260-4309 | www.brc.group
1
2019R1
Step Operation Motion
1 Press and hold ▲&▼simultaneously
more than 3 seconds
Legs begin to move down at a half speed of normal operation
2 Keep pressing ▲&▼Legs move down to the lowest position and rebound 2-5 mm,
then stop
3 Release ▲&▼together Initialization is completed
The initialization procedure must be completed before the first running after table is
installed or parts replaced
Step Operation Motion
1 Press and hold ▲Legs move up
2 Release ▲Legs stop
3 Press and hold ▼Legs move down
4 Release ▼Legs stop
Step Operation Motion
1 Press and hold ▲or ▼，then
release
Run the legs to the position you want the table surface to be
2 Click button S, then click button 1 or 2
or 3 within next 3 seconds
Position 1 or 2 or 3 is saved
Step Operation Motion
1 Press and hold the button 1 or 2 or 3 Legs return to the corresponding position saved
Step Operation Motion
1 Press and hold button S, then press The height information will be changed between centimeters
1 2 3 S
29.0
Alta
Digital Handset Operation
1. Initialization procedure
2. Move table up & down
3. Set handset memory position
4. Operation of stored memory positions
5. Change handset display from centimeter to Inches
MEMORY
UP DOWN SET
MEMORYDISPLAY
Step Operation Motion
1 Press and hold ▲&▼simultaneously
more than 3 seconds
Legs begin to move down at a half speed of normal operation
2 Keep pressing ▲&▼Legs move down to the lowest position and rebound 2-5 mm,
then stop
3 Release ▲&▼together Initialization is completed
The initialization procedure must be completed before the first running after table is
installed or parts replaced
Step Operation Motion
1 Press and hold ▲Legs move up
2 Release ▲Legs stop
3 Press and hold ▼Legs move down
4 Release ▼Legs stop
Step Operation Motion
1 Press and hold ▲or ▼，then
release
Run the legs to the position you want the table surface to be
2 Click button S, then click button 1 or 2
or 3 within next 3 seconds
Position 1 or 2 or 3 is saved
Step Operation Motion
1 Press and hold the button 1 or 2 or 3 Legs return to the corresponding position saved
Step Operation Motion
1 Press and hold button S, then press The height information will be changed between centimeters
The table must be inialized when installed or when components are replaced. This must be done
prior to operang the table for normal use.

BRC Group | 24 Armstrong Ave, Georgetown, ON L7G4R9 | 877-260-4309 | www.brc.group
2
2019R1
6. Verify display switch data to table height
Alta Digital Handset Operation Continued
7. Lock the stroke
8. Unlock the stroke
and hold▼, keep about 3 seconds and inches
2 Release the buttons completed
Values in inches will be displayed in increments of 0.5" inches. Values in
centimeters will be displayed in 1.0 centimeter increments.
Step Operation Motion
1 Set the table at any height,
recommended at the bottom position
Measure the table actual height and write down the number in
inches or in centimeters
2 Press and hold button S, then press
and hold ▲, keep about 3 seconds
The first number is flashing on the screen
3 Release the buttons, then click ▲or
▼to change the first number
The first number is being increased or decreased to the first
number you measured
4 Click button S The second number is flashing on the screen
5 Click ▲or▼to change the number The second number is being increased or decreased to the
second number you measured
6 Click button S The third number is flashing on the screen
7 Click ▲or▼to change the number The third number is being increased or decreased to the third
number you measured
8 Click button S Completed
Step Operation Motion
1 Press and hold ▲or▼, then release Run the legs to the position you want the table surface to be
2 Press and hold button S, then press
and hold 1, keep about 3 seconds
Letter “L” is indicated on the screen. That means the position is
locked at the lowest position that the table can be moved to
3 Release the buttons Completed
1.Legs aren’t able to run below the locked position.
2.Any saved memory positions that are below the locked position will be lost even
after the table is unlocked.You will need to follow SET MEMORY POSITIONS to reset
them.
Step Operation Motion
1 Press and hold button S, then press
and hold 2, keep about 3 seconds
Letter “C” is indicated on the screen. That means the table’s
unlocked and can be moved in full range
2 Release the buttons Completed

BRC Group | 24 Armstrong Ave, Georgetown, ON L7G4R9 | 877-260-4309 | www.brc.group
3
2019R1
Alta
Troubleshooting
Fault Issue Corrective Action
After connecting the power, press ▼or ▲, Re-initialize the table;
the legs have no response. Check if the connection is correct or not;
Please contact your supplier.
After connecting the power, press and hold
▼and ▲, the legs have no response. Check if the connection is correct or not;
Please contact your supplier.
The legs rising slowly. Check if the input power is correct or
not; Please contact your supplier
The legs don’t move according to your
operation. Please contact your supplier.
One leg moves while the other leg does not Check if the connection is correct or not;
move. Please contact your supplier.
Legs only move down and don’t move up. Re-initialize the table;
Please contact your supplier.
Table slides down itself. Check if the weight of the load on the table exceeds 75KG or
not;
Please contact your supplier.
The table goes into initialization frequently. Check if the weight of the load on the table exceeds 75KG or
not;
Check the noise of the motor;
Please contact your supplier.