Bresser MyTime 8020313CM3000 User manual

GB
INSTRUCTION MANUAL
MyTime Thermo/Hygro
8020313CM3000
8020313GYE000
8020313E8G000
8020313WXH000
8020313B4K000
Art. No.
www.bresser.de/download/8020313000000

2
ABOUT THIS INSTRUCTION MANUAL
These operating instructions are to be consid-
ered a component of the device. Please read the
safety instructions and the operating instructions care-
fully before use. Keep these instructions for renewed
use at a later date. When the device is sold or given to
someone else, the instruction manual must be provid-
ed to the new owner/user of the product.
This product is intended only for private use.
GENERAL WARNINGS
CHOKING HAZARD!
Keep packaging material, like plastic bags and rubber
bands, out of the reach of children, as these materials
pose a choking hazard.
RISK of ELECTRIC SHOCK!
This device contains electronic components that oper-
ate via a power source (batteries). Children should only
use the device under adult supervision. Only use the
device as described in the manual; otherwise, you run
the risk of an electric shock.
RISK of FIRE/EXPLOSION!
Do not expose the device to high temperatures. Use
only the recommended batteries. Do not short-circuit
the device or batteries, or throw them into a fire. Exces-
sive heat or improper handling could trigger a short-cir-
cuit, a fire or an explosion!
NOTE!
Do not immerse the unit in water.
Do not subject the unit to excessive force, shock, dust,
extreme temperature or high humidity, which may result
in malfunction, shorter electronic life span, damaged
batteries and distorted parts.
Do not disassemble the device. In the event of a defect,
please contact your dealer. The dealer will contact the
Service Centre and can send the device in to be re-
paired, if necessary.
Use only the recommended batteries. Always replace
weak or empty batteries with a new, complete set of bat-
teries at full capacity. Do not use batteries from different
brands or with different capacities. Remove the batter-
ies from the unit if it has not been used for a long time.
The manufacturer is not liable for damage related to
improperly installed batteries!
GENERAL INFORMATION
This item is available in the following variants. The func-
tions and technical data are the same. They only differ
in its design/in its colour.
8020313CM3000: MyTime Thermo-/Hygro, black
8020313GYE000: MyTime Thermo-/Hygro, white
8020313E8G000: MyTime Thermo-/Hygro, red
8020313WXH000: MyTime Thermo-/Hygro, blue
8020313B4K000: MyTime Thermo-/Hygro, green
SCOPE OF DELIVERY (Fig. 1)
Wall clock, Instruction manual
Required batteries: 1 x 1.5V battery (Size AA/LR6)
Batteries not included with purchase.
PARTS OVERVIEW
Wall clock (Fig. 2)
1. Dial plate
2. Clock hands (hours, minutes, seconds)
3. Humidity display (indoor)
4. Temperature display (indoor)
5. Wall mount
6. Battery compartment
7. M.SET button
8. RESET button
9. REC button
GETTING STARTED/POWER SUPPLY
NOTE!
Insert the batteries for the remote sensor first and then
insert the batteries for the wall clock. Make sure to
B
c
de
f
g
Batteries not included with purchase.
Fig. 2
Hj
i
Fig. 1

3
place the batteries strictly according to the right polar-
ities (+/-) as shown in the battery compartment.
1. Remove the locking pin from the clockwork.
The clock can be operated only after the pin
has been removed.
2. Insert one battery (1.5V, AA/LR6) into battery com-
partment (6).
TIME SETTING
NOTE!
After the clock received the MSF time signal the time
will be set according to the Coordinated Universal
Time (UTC). Summer and winter time change (and re-
verse) is also set automatically. Other deviating times
can be set manually only.
Automatic time setting via MSF time signal
After inserting the battery the time will be set auto-
matically via MSF signal. This process may take a few
minutes. During this process the clock hands will turn
several times with interruption until they will display the
right time.
Initiate to receive the MSF time signal manually
NOTE!
Use this function when e.g. automatic summer/winter
time change does not work or the wall clock tempo-
rarely receives no time signal.
1. Press and hold the REC button (9) for 3 seconds to
start manual search for the MSF signal.
2. The clock hands will move to their start position
(12:00 a.m.) and a the wall clock then tries to re-
ceive the signal.
3. Wait approx. 2-5 minutes until the current time will
be displayed.
Manual time setting
NOTE!
It is necessary to set the time manually in places
where no radio signal is received.
1. Press and hold the M.SET button (7) for approx. 3
seconds.
2. When the minutes hand starts moving you can the
set the time manually:
• Press the M.SET button shortly to set the time in
minutes steps.
• Press and hold the M.SET button to set the time
continously.
3. Release M.SET button to stop manual setting and
save the time automatically and exit manual time
setting mode.
TEMPERATURE AND HUMIDITY DISPLAY
Temperature and humidity measurement work manu-
ally. It may take a few minutes until the value that is
currently measured will be displayed.
MOUNTING/POSITIONING
NOTE!
Make sure you have mounted or placed the device in
a safe way. Otherwise the device may fall down and
heavy damages can occur for which the manufacturer
is not liable.
The wall clock can be mounted on walls with the wall
mount (5).
TROUBLESHOOTING
Transmission collision
Signals from other household devices, such as door
bells, home security systems and entry controls, may
interfere with those of this product and cause tempo-
rarily reception failure. This is normal and does not
affect the general performance of the product. The
transmission of the radio signal will resume once the
interference recedes.
Other malfunctions
If there is no response from the wall clock by key-
strokes or if any other malfunctions occur perform the
following steps.
NOTE!
With this procedure all received data will be deleted.
1. Press RESET button (8) with a pointed instrument
(e.g. pen).
2. The clock hands will move to their start position
(12:00 a.m.) and the wall clock then tries to receive
the signal.
3. Wait approx. 2-5 minutes until the current time will
be displayed.
CLEANING AND MAINTENANCE
Before cleaning the device, disconnect it from the
power supply (remove batteries)!
Only use a dry cloth to clean the exterior of the de-
vice. To avoid damaging the electronics, do not use
any cleaning fluid.
Protect the device from dust and moisture. The batter-
ies should be removed from the unit if it has not been
used for a long time.
DISPOSAL
Dispose of the packaging materials properly, ac-
cording to their type, such as paper or card-

Bresser GmbH
Gutenbergstr. 2 · DE-46414 Rhede
Germany
www.bresser.de · [e-mail]
Errors and technical changes reserved. Manual_8020313000000_MyTime-Thermo-Hygro-MSF_en_BRESSER_v042017a
board. Contact your local waste-disposal service or
environmental authority for information on the proper
disposal.
Do not dispose of electronic devices in the
household garbage!
As per Directive 2002/96/EC of the European Par-
liament on waste electrical and electronic equipment
and its adaptation into German law, used electronic
devices must be collected separately and recycled in
an environmentally friendly manner.
EC DECLARATION OF CONFORMITY
Bresser GmbH has issued a “Declaration of
Conformity” in accordance with applicable
guidelines and corresponding standards. This can be
viewed any time upon request.
WARRANTY & SERVICE
The regular guarantee period is 2 years and begins on
the day of purchase. To benefit from an extended volun-
tary guarantee period as stated on the gift box, registra-
tion on our website is required. You can consult the full
guarantee terms as well as information on extending the
guarantee period and details of our services at www.
bresser.de/warranty_terms.