Breville AquaStation Chilled User manual

the AquaStation™ Chilled
Instruction Book - Suits all LWA300 Models

2
BREVILLE
RECOMMENDS
SAFETY FIRST
At Breville we are very safety
conscious. We design and
manufacture consumer
products with the safety of you,
our valued customer, foremost
in mind. In addition, we ask
that you exercise a degree of
care when using any electrical
appliance and adhere to the
following precautions. Misuse
can cause potential injuries.
IMPORTANT
Do not store the water dispens-
er on any other side other than
upright and level on its support
feet. This is important for the
compressor.
MAIN TECHNICAL SPECIFICATIONS
Product Model LWA300BSS
Filter Model LWA063WHT
Filter Life 90 days or approximately
200L, whichever comes first
Rated Voltage 220-240V
Rated Frequency 50Hz
Rated Power Consumption 100 W
Applicable Water Source Municipal tap water: 5~40°C
Product Dimensions
(LxWxH) Approx. 391 x 273 x 455
Weight (kg) Approx. 9.54
Tested against: NSF/ANSI Standard 42 for
the reduction of chlorine (taste and odour),
& NSF/ANSI 372, lead content.
Tested to remove/reduce microplastics, floating
particles/sediment, pesticides, chlorine, limescale
& heavy metals.
Testing was performed under standard laboratory
conditions. The contaminants or other substances
removed or reduced by this filter are not
necessarily in all users’ water. Filter performance
may vary based on local water conditions.
IMPORTANT
SAFEGUARDS
READ ALL INSTRUCTIONS
BEFORE USE AND SAVE
FOR FUTURE REFERENCE
• Carefully read all instructions
before operating and save for
future reference.
• Remove and safely discard
any packaging material and
promotional labels before using
the AquaStation™ Chilled for
the first time.
2 Breville Recommends Safety First
8 Components
10 Features
12 Assembly
15 Operation
17 Care, Cleaning & Storage
19 Troubleshooting
Contents

3
• Always ensure the appliance
is properly assembled before
use. Follow the instructions
provided in this book.
• The AquaStation™ Chilled
must be used only with the
Breville filter supplied or
replacement product code
LWA063.
• This appliance has been
designed specifically for the
purpose of filtering and chilling
drinking quality water only.
Under no circumstances should
this appliance be used to chill
any other liquids.
• Do not place the appliance
near the edge of a bench or
table during operation. Ensure
that the surface is level, clean
and free of water and other
substances.
• Do not operate the appliance
on a sink drain board.
• Do not operate the appliance in
an enclosed space, or within a
cupboard.
• Never immerse the appliance,
power cord or power plug in
water, or allow moisture to
come into contact with these
parts.
• Do not move the appliance
while it is switched on.
• Always ensure the appliance
returns to standby mode, then
turn the power off at the power
outlet and remove the power
plug from the power outlet
before attempting to move the
appliance, when the appliance
is not in use and before
cleaning and storing.
• Do not remove the water tank
from the power base during
operation.
• If the water tank is removed
from the power base during
water dispensing, the appliance
will automatically stop.
• Always fill the water tank with
water between the minimum
(MIN) and maximum (MAX) as
marked on the water tank.
• Too little water will result in the
appliance not operating and
Water Droplet will turn solid
red. Filling above the maximum
mark (MAX) may result in
water splashing from the water
tank.
• Ensure the water level is
always above the MIN level for
optimum dispensing flow rate.
• The lid should always be
correctly fitted on the water
tank except when refilling.
• Do not place the appliance
in direct sunlight. Colour
fading and discolouration may
occur when the appliance is
consistently exposed to sunlight

4
• Allow the appliance to cool
down before moving or
cleaning any parts.
• This appliance is intended to
filter tap water only. Do not put
water of unknow quality into
the appliance. Use only cold or
room temperature water.
Do not use for the preparation
of baby formula.
• Do not fill the water tank with
hot water. Water added to the
water tank should not be less
than 5°C or more than 40°C.
If water in the tank is outside
these temperatures, discard and
fill with cold tap water.
• Do not leave the appliance
unattended during operation.
• Do not remove filter whilst the
appliance is operating.
WARNING
• Do not operate the appliance on
an inclined plane. Do not move
appliance unless the appliance
is turned off and unplugged
from the power outlet.
• Keep the appliance and all
parts clean. Follow the cleaning
instructions provided in this
book.
• Any procedure not listed in
this instruction book should
be performed at an authorised
Breville Service Centre.
IMPORTANT SAFEGUARDS
FOR ALL ELECTRICAL
APPLIANCES
• Fully unwind the power cord
before use.
• Connect only to a 230V or
240V power outlet.
• The appliance must be used on
a properly grounded outlet. If
you are not sure, please consult
a qualified electrician.
• Do not, under any
circumstances, modify the
power plug or use a power plug
adapter.
• Do not place this appliance on
or near a heat source, such as a
hot plate, oven or heaters.
• Position the appliance at a
minimum distance of 20cm
away from walls, curtains and
other heat or steam sensitive
materials and provide adequate
space above and on all sides for
air circulation.
• Do not let the power cord
hang over the edge of a bench
or table, touch hot surfaces
or become knotted. Keep
away from hot gas or electric
burners, or where it could touch
a heated oven.
• This appliance is for household
use only. Do not use this
appliance for anything other
than its intended use. Do not

5
use in moving vehicles or boats.
Do not use outdoors. Misuse
may cause injury
• This appliance can be used
by children aged from 8 years
and above and persons with
reduced physical, sensory or
mental capabilities or lack of
experience and knowledge
if they have been given
supervision or instruction
concerning use of the appliance
in a safe way and understand
the hazards involved.
• Children should be supervised
to ensure that they do not play
with the appliance.
• Always turn the appliance to
the OFF position, switch off at
the power outlet and unplug
at the power outlet when the
appliance is not in use.
• Before cleaning, always turn the
appliance to the OFF position,
switch off at the power outlet,
unplug at the power outlet
and remove the power cord, if
detachable, from the appliance
and allow all parts to cool.
• To protect against electric
shock, do not immerse the
power cord, power plug or
appliance in water or any other
liquid or allow moisture to
come in contact with the parts,
unless it is recommended in the
cleaning instructions.
• Any maintenance other than
cleaning should be performed
at an authorised Breville
Service Centre
• It is recommended to regularly
inspect the appliance. To
avoid a hazard, do not use the
appliance if power cord, power
plug or appliance becomes
damaged in any way. Return
the entire appliance to the
nearest authorized Breville
Service Centre for examination
and/or repair.
• The installation of a residual
current device (safety switch)
is recommended to provide
additional safety protection
when using electrical
appliances. It is advisable
that a safety switch with a
rated residual operating
current not exceeding 30mA
be installed in the electrical
circuit supplying the appliance.
See a qualified electrician for
professional advice.
• During electrical storms,
the appliance should be
disconnected from the power
source at the wall socket to
prevent any electrical surges
that may arise during the storm
and which may inadvertently
cause damage to the appliance
and its electronic componentry.

6
• Cleaning and user maintenance
shall not be made by children
without supervision.
SPECIFIC INSTRUCTIONS
FOR WATER FILTER
• Filter cartridge should be kept
out of reach of children.
• Store any unused filter
cartridges in a dry place sealed
in the original packaging.
• Protect filter cartridges from
heat and direct sunlight. Only
remove from packaging before
using.
• Do not use a filter cartridge that
is damaged.
• Do not open filter cartridge
housing to access the material
inside.
• If you are absent for a prolonged
period of time, empty and clean
the water tank and replace the
filter cartridge before next use.
• Refer to the filter installation
instructions found in the
'Assembly' section of these
instructions.
BREVILLE ASSIST™ PLUG
• Your Breville appliance comes
with a unique Assist™ Plug,
conveniently designed with a
finger hole in the power plug
for easy and safe removal from
the power outlet. For safety
reasons, it is recommended
you plug your Breville
appliance directly into its own
electrical outlet on a dedicated
circuit separate from other
appliances. If the electric
circuit is overloaded with other
appliances, your appliance
may not function properly. Use
in conjunction with a power
strip or extension cord is not
recommended.
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS

7
Components
A
C
D
F
E
H
I
J
K
G
B
A. Water tank lid
with easy-grip handle
B. The Activ360™ 4-Stage
Filter
with pull ring for
easy removal
C. Filter holder
D. Water tanks
Including a removable,
external 6L water tank
plus an internal 2L chilling
chamber (not shown)
NOTE - Total external tank
capacity is 6L, however, it is
recommended to always fill the
external water tank with water
between the minimum (MIN- 2L)
and maximum (MAX- 5L) as
marked on the water tank.
Filling above the maximum mark
(MAX-5L) may result in water
splashing from the water tank.
E. Function Dial &
Start/Stop Button
F. Control Panel
Indicator lights START/
STOP,
5°C, 10°C, 15°C, Ambient,
Filter Reset, Cooling, Ready
G. Dispensing spout
H. Dispensing area
20cm cup clearance height
with tray in place, 23cm
height if drip tray removed
I. Detachable magnetic drip
tray
J. Removable tray grill
for cleaning
K. Non-marking,
non-slip feet
Not Shown
• Breville Assist™ Plug
• Drain Plug & Cap
(Located underneath unit)

8
Control Panel
READY
FILTER
RESET
AMBIENT
5ºC
10ºC
15ºC
START | STOP
START/STOP
Water droplet light flashes 3 times then
illuminates white when ready or when
dispensing water. The light extinguishes when
in standby mode.
5°C, 10°C & 15°C
Light illuminates against the selected cold
temperature.
CHILLING
Illuminates blue when compressor is on.
Flashes on and off to indicate that the
compressor is turning on and off to maintain
the set temperature (ambient, 5°C, 10°C &15°C).
READY
Light illuminates white when set temperature
has been reached
AMBIENT
Light illuminates white when selected.
FILTER RESET
Light illuminates as a reminder to change the
filter cartridge once the filter life timer has
counted down.
FILL TANK
The water droplet light on the START/STOP
button will illuminate solid red to alert the user
that the water tank needs to be filled. The unit
will not dispense water until the tank is refilled.
Once the tank has been filled, The water
droplet light on the START/STOP button will
no longer illuminate.
NOTE
Take care when removing the water tank from
the base after use as residual water may drip.
NOTE
• The unit will not dispense any water while the
tank is below the minimum water level.
• Ensure the water level is always above the
MIN level for optimum flow rate.
PROGRAM TABLE
Function Water Dispensing
Flow Rate
^Preset Temp °C ^Temp Range °C Temp +/-
Increments
Preset Volume
MLS
Cold 1L/min 55 to 15 5Stops dispensing
after 1 minute.
Ambient 1L/min Temp of Water
inside Water Tank# N/A N/A Stops dispensing after 1 minute.
^Temperature is measured in the chilling chamber not from the spout.
#Dispensed Ambient water temperature will vary.

9
NOTES
• Cold water temperature settings are measured
in the chilling chamber not the dispensed
temperature at the spout or in the cup.
• When dispensing ambient water, if START/
STOP is not pressed to stop water flow,
dispensing will automatically stop after 60
seconds.
• Ambient water temperature will vary. The
temperature dispensed will be influenced by
the external factors surrounding the unit itself.
An increase in the air temperature will cause
water tank temperature to increase as well.
• If the water temperature in the tank becomes
too warm, discard and replace with cold tap
water. Water temperature in the tank should
not be dispensed if above 40°C.

10
WHAT IS THE AQUASTATION™
CHILLED?
The Breville AquaStation™ Chilled when used
with the Activ360™ 4-stage fast flow water
filtration system, provides cleaner, great-
tasting ambient or cold filtered water.
The Activ360TM Filter, with 4 distinct levels
of filtration, removes contaminants from water
that can cause bad taste and odour, which may
potentially be harmful to your health.
1. Stage 1- Pre-Sediment Filter
Filters microplastics and floating particles
2. Stage 2- Ion-Exchange Resin Filter
Filters limescale and metals
3. Stage 3- Activated Carbon Filter
Filters Pesticides and Chlorine
4. Stage 4- Post Filter
Filters fine particles
* 4-stage fast flow filtration tested and/or
certified to remove/reduce microplastics,
floating particles/sediment, pesticides, chlorine,
limescale & heavy metals.
For more information, visit Breville.com
No Plumber Required
The benchtop unit will start to work as soon as
assembled, water is added and the power cord
is connected to a power source; then simply
press to dispense filtered water. No need to
plumb into mains water.
Filter Life Counter
The AquaStation™ unit reminds you to replace
the filter every 90 days or approximately 200L
of water*, whichever comes first, to ensure the
best filtration performance.
You may choose to change your filter more
frequently in areas with poor water quality.
*The filter change alert is set at 90 days or
approximately 200L of water, whichever
comes first, with performance based on typical
municipal drinking water quality, however,
water quality may vary considerably from one
area to the next which may affect the life of the
water filter and more frequent replacement may
be required.
Filter Reset Replacement Alert
START/STOP button continuously flashes in
red as a reminder to change the filter cartridge
once the filter timer has counted down.
Removable, Magnetic Drip Tray
The drip tray can easily be removed to
accommodate different sizes of cups, glasses
or reusable bottles. The magnetic edge helps
to keep the tray in place when attached at the
base. Empty regularly to avoid overspill.
Water Level Sensor
The water tank is equipped with a floating
sensor to detect water levels and will
automatically stop dispensing when the water
level becomes too low. The water droplet light
on the START/STOP button will illuminate
solid red.
One-way Tank Valve
The water tank has been designed with a
one-way valve so that it can be removed from
the unit even if water is still in the tank. This
prevents the water from leaking when removed
from the dispensing unit. Be mindful however
that there may be some residual water droplets
when removed.
Features