Breville Mistic 2 in 1 Connect LTF408 User manual

1
Instruction Book - Suits all LTF408 Models
the Mistic 2 in 1™Connect
Tower Fan & Humidifier
LTF408_ANZ_IB_D20.indd 1LTF408_ANZ_IB_D20.indd 1 15/7/20 2:14 pm15/7/20 2:14 pm

2
BREVILLE
RECOMMENDS
SAFETY FIRST
At Breville we are very safety
conscious. We design and
manufacture consumer
products with the safety of you,
our valued customer, foremost
in mind. In addition, we ask
that you exercise a degree
of care and adhere to the
following precautions.
IMPORTANT
SAFEGUARDS
READ ALL INSTRUCTIONS
BEFORE USE AND SAVE
FOR FUTURE REFERENCE
• Carefully read all instructions
before operating the
Mistic 2 in 1TM Connect
Tower Fan & Humidifier for
the first time and save for
future reference.
• Remove and safely discard
any packaging material and
promotional labels before
using for the first time.
• To eliminate a choking hazard
for young children, remove and
safely discard the protective
cover fitted to the power plug
of this tower fan.
• When unpacking the tower
fan, check to see you have
received all the items listed in
the parts list, before discarding
the packaging.
• Do not place the tower fan
near the edge of a bench
or table during operation.
Ensure that the surface is level,
clean and free of water and
other substances.
• Always ensure the tower fan
is properly assembled before
use. Follow the instructions
provided in this book.
• This tower fan is intended for
household use only and not for
commercial or industrial use.
• To avoid electrical circuit
overload, it is recommended
that no other appliances are
plugged into the same circuit
as your fan, when it is in use.
2 Breville Recommends Safety First
8 Components
9 Control Panel
10 Display Screen
11 Features
11 Assembly
12 Operation
13 Functions
17 Wi-Fi Connectivity
18 Care, Cleaning & Storage
Contents
LTF408_ANZ_IB_D20.indd 2LTF408_ANZ_IB_D20.indd 2 15/7/20 2:14 pm15/7/20 2:14 pm

3
• Disconnect the power plug
before assembling, dismantling
or before cleaning and when
the tower fan is not in use.
• Avoid touching mobile parts
of the tower fan.
• Never insert fingers, pencils or
any other objects through the
guards whenever the power plug
is connected, in particular while
the tower fan is switched on.
• The tower fan must not
be used if the base is not
fastened correctly, according
to the instructions provided
in this book.
• Do not operate in the presence
of explosives and/or flammable
fumes or liquids.
• Never carry the tower fan by
the cord or yank the cord to
disconnect from the power
outlet; instead, grasp the plug
and pull to disconnect.
• Do not pull the cord around
sharp edges or corners.
• Allow the fan blade to stop
completely and the fan guard
to close, then always switch off
at the power outlet and unplug
the tower fan from the outlet:
- Before leaving it unattended -
Before attempting to move the
appliance - Before cleaning and
maintenance unless otherwise
specified in this booklet -
Immediately after use.
• To prevent damage to the
tower fan, do not use alkaline
cleaning agents when
cleaning. Use a soft cloth and
a mild detergent.
• Do not place anything on top
of the tower fan when assembled,
when in use or when stored.
• The tower fan is not intended
to be operated by means of
an external timer or separate
remote-control system or any
other device that switches the
tower fan on automatically.
• Keep the tower fan &
humidifier clean. Follow the
cleaning instructions provided
in this book.
RELATIVE TO
HUMIDIFICATION
• Do not place the tower fan on a
rug, carpet, wooden flooring, or
any other surface that may be
damaged by exposure to water
or moisture.
• Do not locate the tower fan
directly below or close to a
mains electricity supply socket.
• Do not use the tower fan
without sufficient water in the
water container.
LTF408_ANZ_IB_D20.indd 3LTF408_ANZ_IB_D20.indd 3 15/7/20 2:14 pm15/7/20 2:14 pm

4
• Do not use the humidifier
unless it has been cleaned
according to the instructions.
• Humidifier mist may not be
visible in certain conditions
(impacted by light, background
colour etc.) or at the
lowest setting.
• Humidifier is suitable for use in
dry locations only. Do not use
outdoors or on wet surfaces.
Do not use in bathrooms,
laundry areas or similar
indoor locations.
• Do not spray any flammable
materials such as insecticides
or fragrance around
the humidifier
• Do not use this humidifier
when you have used indoor
smoke-type repellents
or in places with oily
residue, burning incense or
chemical fumes.
• Do not use in areas where
petrol, paint or flammable
liquids are used or stored
or where there are vapours
present. Do not use in
conjunction with or directly
next to an air freshener or
similar products.
• Do not pour water into any
openings except for the
water container.
• When filling or refilling, only
fill the water container with
cold tap water or distilled water.
Do not use ground water or
hot water.
• Always use clean tap or
distilled water to prevent
clogging and damage to
the transducer.
• Do not put any substance
other tap water into the water
container. Do not add fragrance
or any chemical substance
into the water. Use only water
(tap, purified, mineral, any
sort of portable water). If other
additives are used, the plastic
material and the membrane
may become discoloured and/
or damaged.
• Water in the water container
is not suitable for drinking.
Do not drink this water, and
do not use it to feed animals or
water plants. When you empty
the water container, pour the
water in the water container
down a drain.
• Do not use the humidifier
in a room with major
temperature changes as this
may cause condensation inside
the humidifier.
LTF408_ANZ_IB_D20.indd 4LTF408_ANZ_IB_D20.indd 4 15/7/20 2:14 pm15/7/20 2:14 pm

5
• Position the tower fan so that
the mist nozzle is not directed
towards objects or a wall as the
immediate vicinity of the tower
fan may become damp.
• If not using the humidifier for
a long time, clean and dry the
water container before storage.
• Clean the water container
weekly if the humidifier is
used extensively.
• A comfortable humidity level
is considered to be between
40%RH to 60%RH
• Empty any remaining water
from the water container and
water inlet basin when the
humidifier is not in use.
• The humidifier is not intended
to be operated by means of
an external timer or separate
remote-control system or any
other device that switches the
tower fan on automatically.
• Keep the tower fan &
humidifier clean. Follow the
cleaning instructions provided
in this book.
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
LTF408_ANZ_IB_D20.indd 5LTF408_ANZ_IB_D20.indd 5 15/7/20 2:14 pm15/7/20 2:14 pm

6
IMPORTANT
SAFEGUARDS
FOR ALL
ELECTRICAL
APPLIANCES
• Fully unwind the power cord
before use.
• Connect only to a 230V or
240V power outlet.
• Do not let the power cord hang
over the edge of a bench or
table, touch hot surfaces or
become knotted.
• To protect against electric
shock, do not immerse the
power cord, power plug or
appliance in water or any other
liquid or allow moisture to
come in contact with the part,
unless it is recommended in
the cleaning instructions.
• The appliance is not
intended for use by persons
(including children) with
reduced physical, sensory
or mental capabilities, or
lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning use
of the appliance by a person
responsible for their safety.
• Children should be supervised
to ensure that they do not play
with the appliance.
• It is recommended to regularly
inspect the appliance. To
avoid a hazard, do not use the
appliance if power cord, power
plug or appliance becomes
damaged in any way. Return
the entire appliance to the
nearest authorised Breville
service centre for examination
and / or repair.
• Any maintenance other than
cleaning should be performed
at an authorised Breville
Service Centre
• This appliance is for household
use only. Do not use this
appliance for anything other
than its intended use. Do not
use in moving vehicles or
boats. Do not use outdoors.
Misuse may cause injury.
• The installation of a residual
current device (safety switch)
is recommended to provide
additional safety protection
when using electrical
appliances. It is advisable
that a safety switch with a
rated residual operating
current not exceeding 30mA
be installed in the electrical
circuit supplying the appliance.
See your electrician for
professional advice.
LTF408_ANZ_IB_D20.indd 6LTF408_ANZ_IB_D20.indd 6 15/7/20 2:14 pm15/7/20 2:14 pm

7
• During electrical storms,
the appliance should be
disconnected from the power
source at the wall socked to
prevent any electrical surges
that may arise during the storm
and which may inadvertently
cause damage to the appliance
and its electronic componentry.
• Always turn the appliance to
the OFF position, switch off at
the power outlet and unplug
at the power outlet when the
appliance is not in use.
• Before cleaning, always turn the
appliance to the OFF position,
switch off at the power outlet,
unplug at the power outlet
and remove the power cord, if
detachable, from the appliance
and allow all parts to cool.
• Do not place this appliance on
or near a heat source, such as
hot plate, oven or heaters.
• Position the appliance at a
minimum distance of 20cm
away from walls, curtains and
other heat or steam sensitive
materials and provide adequate
space above and on all sides
for air circulation.
LTF408_ANZ_IB_D20.indd 7LTF408_ANZ_IB_D20.indd 7 15/7/20 2:14 pm15/7/20 2:14 pm

8
A. Carry Handle
B. Air Outlet Grille
C. Mist Nozzle
D. Front Housing
E. Non-tilt Base
F. Rear Grille
G. Water Container Release Button
H. Water Container
I. Rear Housing
J. Water Outlet Cap
K. Control Panel
L. LED Display Screen
M. Remote Control
NOT PICTURED
Front Pivot Grille Cover
Water Inlet Basin
Water Container Cap and Seal
Power Cord and Plug
cComponents
A
B
D
C
E
F
K
L
I
H
G
J
OSC
HUMIDITY
MODE
TIMER
M
LTF408_ANZ_IB_D20.indd 8LTF408_ANZ_IB_D20.indd 8 15/7/20 2:14 pm15/7/20 2:14 pm

9
C
B
cControl Panel
CONTROL PANEL
A. HUMIDITY
B. DOWN
C. POWER ON/OFF
D. OSCILLATION ON/OFF
E. UP
REMOTE CONTROL PANEL
F. TIMER
G. OSCILLATION ON/OFF
H. POWER ON/OFF
I. UP
J. DOWN
K. HUMIDITY
L. MODE
OSC
HUMIDITY
MODE
TIMER
F K
L
G
H
I
J
AD
E
LTF408_ANZ_IB_D20.indd 9LTF408_ANZ_IB_D20.indd 9 15/7/20 2:14 pm15/7/20 2:14 pm

10
cDisplay Screen
ECO MODE
NIGHT MODE
NATURAL MODE
FAN SPEED
AMBIENT TEMPERATURE
HUMIDITY
TIMER
Wi-Fi
LTF408_ANZ_IB_D20.indd 10LTF408_ANZ_IB_D20.indd 10 15/7/20 2:14 pm15/7/20 2:14 pm

11
FFeatures
WHAT IS THE 2 IN 1
The Breville Mistic 2 in 1™ Connect Tower Fan
& Humidifier features both a cooling fan and
a humidifier. The humidification feature will
assist in keeping a comfortable environment
at home by adding water vapour (moisture)
to the surrounding atmosphere.
aAssembly
BEFORE FIRST USE
Before using your Mistic 2 in 1™ Connect
Tower Fan & Humidifier for the first
time, remove all packaging material and
promotional labels. Check for any missing or
damaged parts as per the components list.
ASSEMBLE THE BASE
To assemble the base to the body of the tower
fan, turn the body upside-down. Align mark ‘1’
on the base with mark ‘1’ on the bottom of the
body. (Fig 1)
Fig 1
Mark 1 on
the base
Mark 1
on the
unit body
To lock the base to the body, turn the base
clockwise so mark ‘1’ of the body aligns with
mark ‘2’ on the base. (Fig 2) Turn the tower
fan upright.
Fig 2
LTF408_ANZ_IB_D20.indd 11LTF408_ANZ_IB_D20.indd 11 15/7/20 2:14 pm15/7/20 2:14 pm

12
oOperation
OPERATING YOUR 2 IN 1 TOWER
FAN & HUMIDIFIER
1. Place the tower fan on a flat surface. Insert
the power plug into a 230V or 240V power
outlet and switch on at the outlet.
2. Touch the button on the control panel
to turn the tower fan on and the front
pivot grille cover will open softly. When
switched on for the first time, the fan will
start automatically on NORMAL mode, at
fan speed 5.
3. The LED display screen will illuminate
and alternate between the room ambient
temperature and current fan setting.
Both and . will illuminate alternately,
depending on when ambient temperature
is displayed on the LED display screen.
To turn the tower fan off at any time,
touch the button on the control
panel and the front pivot grille cover will
automatically close.
nNOTE:
• The fan will always operate when turned on.
• The fan cannot be turned off to operate on
humidification only. The humidifier however
can be turned on or off to operate on fan only.
• When the tower fan is ON, Wi-Fi will attempt
to connect automatically. If a connection
has been made, the Wi-Fi symbol will stop
flashing and illuminate. If a connection
is not made, the Wi-Fi symbol will stop
illuminating. See Wi-Fi Connectivity in this
book for more details.
• After 15 hours of non-stop operation, the
tower fan will automatically turn off.
• The tower fan is fitted with a power saving
feature. The LED display screen will dim
after 40 seconds if none of the control panel
buttons have been touched. The LED display
screen will re-illuminate if a button on the
control panel is touched.
ROOM AMBIENT TEMPERATURE
Your Breville Mistic 2 in 1™ Connect
Tower Fan & Humidifier is fitted with a
temperature sensor that detects the room
temperature (in °C) which will display
on the LED display screen. The number
displayed is only an indication of the room
temperature and will vary depending on the
location of the fan in the room.
LTF408_ANZ_IB_D20.indd 12LTF408_ANZ_IB_D20.indd 12 15/7/20 2:14 pm15/7/20 2:14 pm

13
oFunctions
COOLING MODES
Your tower fan has 4 cooling modes:
NORMAL, NATURAL, NIGHT and ECO. The
tower fan will start automatically on NORMAL
mode on speed 5 when the fan is first switched
on or after it is reconnected to a power supply.
1. To choose between these cooling modes,
press the button found on the remote
control only, until the corresponding
symbol illuminates on the LED display
screen. The LED display screen will
illuminate and alternate between the
room ambient temperature and current
fan setting.
2. To change or cancel a cooling mode, press
the button to change the mode, or the
ON/OFF button to stop operation.
nNOTE:
The tower fan has a memory function and will
return to the same fan speed and mode it was
set at when it was turned off. This will only
occur if the tower fan is not unplugged and/or
switched off at the power point.
The memory function is not available for
humidification mode.
NORMAL MODE
NORMAL mode has 12 fan speed settings;
1 being the lowest, and 12 the highest, with
the default speed at 5. To choose a fan speed
setting, touch the and buttons on either
the control panel or the remote, until the
desired number flashes on the LED display
screen 3 times, then sets.
NORMAL mode is the default mode settings
for this tower fan. In NORMAL mode, no light
illuminates on NATURAL, NIGHT or ECO
on the LED display screen.
NATURAL MODE
Continuous air flow can create a chilling
effect on the skin and a discomfort when
exposed for too long. NATURAL mode
generates a gentle breeze to maintain body
temperature by simulating wind blowing
rhythm, automatically alternating wind
speeds according to pre-programmed cycles.
NATURAL mode has 4 cycle programs.
Each cycle is made of two low speeds and
two high speeds alternating randomly
within a fluctuating time range.
To choose a cycle program, touch the and
buttons on either the control panel or the
remote until the desired number flashes
on the LED display screen for 3 seconds,
then sets.
Cycle
program
Low Speeds
(10-19 secs)
High Speeds
(5-14 secs)
11 & 2 3 & 4
25 & 6 7 & 8
37 & 8 9 & 10
49 & 10 11 & 12
LTF408_ANZ_IB_D20.indd 13LTF408_ANZ_IB_D20.indd 13 15/7/20 2:14 pm15/7/20 2:14 pm

14
NIGHT MODE
NIGHT mode ensures the tower fan remains
quiet, dimming the lights on the control panel
and LED display screen, allowing for a more
comfortable night’s rest.
To choose a fan speed setting, touch the
and buttons on either the control panel or
the remote until the desired number flashes
3 times on the LED display screen, then sets.
Depending on the set fan speed, the fan
speed will reduce by 1 every hour until the
lowest speed is reached (speed 1).
ECO MODE
ECO mode will save energy and operate
quietly on fan speed 1 and is ideal to be
used during sleep or when left on for a long
period of time.
nNOTE:
Fan speed in ECO mode cannot be
manually adjusted.
AUTO-OFF AND AUTO-ON TIMER
The tower fan comes with a 12-hour auto-
off timer to turn the tower fan off after a
set number of hours. It also comes with a
12-hour auto-on timer that will turn on after
a set number of hours. Both can be set in 30
minute (0.5) increments up until 10 hours.
After 10 hours, both can be set in 1 hour
(1) increments and will switch the tower
fan into standby mode after the selected
number of hours have elapsed. The auto-off
timer and auto-on timer can be set on any
MODE, including humidification mode.
Either timer may be set by using the remote
control only.
AUTO-OFF TIMER Example: Set the
auto-off timer to 6 hours, and the tower fan
will stop operating after 6 hours.
AUTO-ON TIMER Example: Set the
auto-on timer to 6 hours, and the tower fan
will start operating after 6 hours.
To confirm the setting, press the timer
button again.
AUTO-OFF TIMER
Touch the button on the remote and
will flash along with “0.5” on the LED
display screen. Touch the and buttons
on either the control panel or the remote
control, until the desired number of hours
flashes on the LED display screen. Press
the button on the remote control to
start the timer. The time will display on
the LED display screen, and the symbol
will illuminate. The timer will start on the
selected mode, and the mode will stop
automatically once the timer has expired.
nNOTE:
If TIMER is touched on the remote but
no action is taken, the tower fan will exit
TIMER. Touch the button on the remote
to return to TIMER.
The LED display screen will not indicate
the remaining auto-off time, instead the
LED display screen will return to the set fan
setting. Press the button on the remote,
and the remaining time will display on the
LED display screen.
To cancel the pre-set auto-off time anytime
once the timer is set, press and hold the
button on the remote for 2 seconds and the
symbol will no longer illuminate.
nNOTE
• The timer can be set on all modes and all
modes can be adjusted at any time once the
timer is set.
• The tower fan will switch to standby mode
once the set time has elapsed.
• To check the pre-set time left on the LED
display screen, press the button on the
remote once.
LTF408_ANZ_IB_D20.indd 14LTF408_ANZ_IB_D20.indd 14 15/7/20 2:14 pm15/7/20 2:14 pm

15
AUTO-ON TIMER
Auto-on can only be set when the tower fan
is on standby mode.
Press the button on the remote. The
symbol will begin to flash and “0.5” will
display on the LED display screen. Press the
and buttons on either the control panel or
the remote until the desired number flashes
on the LED display screen.
Press the button again on the remote to
set the auto-on timer. The time will display
on the LED screen and the symbol
will illuminate. The timer will start on the
last selected mode, and the fan will start
automatically once the time has elapsed.
nNOTE:
If TIMER is pressed on the remote but
no action is taken, the tower fan will exit
TIMER. Press the button on the remote
to return to TIMER.
The LED display screen will not display the
remaining auto-off time, instead the display
will return to the set fan setting. Press the
button on the remote and the remaining
time will display on the display screen.
To cancel the auto-on time anytime once the
timer is set, touch and hold the button for
2 seconds and the symbol will no longer
illuminate.
nNOTE
• The auto-on timer can only be set when the
fan is on standby mode.
• The tower fan will turn on once the auto-on
timer has elapsed.
• The tower fan will operate on the last
selected mode.
• To check the pre-set time left on the LED
display screen, press the button on
the remote.
OSCILLATION
The tower fan has horizontal oscillation.
The oscillation can be set on any MODE,
including humidification mode.
To activate oscillation, touch the button
once. The tower fan will move left to
right continuously.
To stop and direct the orientation of your
tower fan during oscillation, touch the
oscillation symbol again when the airflow
has reached your preferred position.
HUMIDIFICATION
The Breville Mistic 2 in 1TM Connect Tower
Fan & Humidifier comes with the added
benefit of humidification. The humidifier
can be set on any MODE and emits a mist at
the same time that the fan is operating.
To fill the water container before use, press
the water container release button found
on the outside of the water container on the
back of the tower fan and it will disengage
for easy removal. Turn the water container
upside-down and remove the water
container cap. Fill the water container with
fresh water and replace the water container
cap before reassembling the water container
(upright) back into the tower fan.
To activate the humidifier function, touch
the button once. The tower fan will
automatically release mist on low from the mist
nozzle. The symbol will illuminate on the
LED display screen before setting.
To increase the mist output from LOW to
HIGH, touch the button again. To turn
the humidification off, touch the button
again, and the mist output will automatically
stop.
Once the water container is empty, or the
water level is too low, the symbol will
begin to flash. Refill the water in the water
container and replace the water container
into the tower fan. The symbol will stop
flashing and stay off. Humidification will
need to be re-activated.
LTF408_ANZ_IB_D20.indd 15LTF408_ANZ_IB_D20.indd 15 15/7/20 2:14 pm15/7/20 2:14 pm

16
nNOTE
Keep the tower fan straight when moving
if there is water in either the water tank or
water inlet basin as water may spill out.
Some water may remain in the basin of the
water inlet basin at the back of the tower
fan, separate to the water container. This
is normal. To drain excess water after use,
position the tower fan above a drainage
source and remove the water outlet cap from
the back of the tower fan. Tilt the tower fan
backwards towards the drainage source.
REMOTE CONTROL
The tower fan comes with a remote control.
This remote control features the same
icons as the control panel on the tower
fan and can be used the same way. The
remote control has two additional controls
not found on the control panel. The two
functions MODE and TIMER can be set
using the remote control only. Refer to the
MODE and TIMER sections of this book for
more details.
To avoid misplacing your remote control,
place the remote control between the
carry handle, and the controls of the tower
fan frame.
USING THE REMOTE CONTROL
Your remote control requires 2 x AAA
batteries (NOT INCLUDED).
To insert the batteries, open the battery
compartment at the back of the remote
by forming a good grip of the remote and
pressing then sliding the battery cover
towards the bottom of the remote. The
battery cover should slide off.
Insert the 2 batteries paying attention to the
polarity (+ and -).
Slide the back battery cover back onto the
remote by lining the 2 tabs on the battery
cover with the 2 grooves on the back
of the remote body. Ensure the battery
compartment is correctly secured so
batteries remain in place.
nNOTE
To use the remote control, it must be
pointed at the LED display screen and used
within five meters of the tower fan.
LTF408_ANZ_IB_D20.indd 16LTF408_ANZ_IB_D20.indd 16 15/7/20 2:14 pm15/7/20 2:14 pm

17
Wi-Fi
Connectivity nNOTE
To control the tower fan using the app,
the tower fan must be plugged in to an
active power outlet and turned on. If the
tower fan is turned off or disconnected from
the power, then the app cannot connect via
the network.
CONNECT YOUR 2 IN 1 TOWER FAN &
HUMIDIFIER TO WI-FI
1. Ensure the mobile device is connected to
a home Wi-Fi network.
2. To set up the tower fan, turn it on at the
power outlet. Once on, the symbol will
flash fast on the display panel. The tower
fan is now ready to connect.
3. Log into your Breville Home Connect™
app account and stay on the “Home” page.
To add the tower fan to the list. Touch ‘Add
Device’ or the symbol found in the top
right-hand corner of the screen. Follow the
prompts in the app.
4. If the connection is successful, the tower
fan will appear in the main page of the app
and the Wi-Fi symbol light on the purifier
will illuminate.
The Breville Mistic 2 in 1™ Connect Tower
Fan & Humidifier can offer remote operation
by using a home Wi-Fi connection and the
Breville Home Connect™ app downloaded
to a compatible mobile phone through the
Google Play store or Apple App store.
To go straight to the appropriate app store,
scan the QR code below.
For instructions on how to use the app, scan
the QR code below, refer to the Quick Start
Guide that can be found in the box or go to:
tinyurl.com/HomeConnectQuickStart
nNOTE
The Breville Home Connect™ app is
compatible with mobile phones running
Android®5.0 or later and iOS devices 9.0
or later.
LTF408_ANZ_IB_D20.indd 17LTF408_ANZ_IB_D20.indd 17 15/7/20 2:14 pm15/7/20 2:14 pm

18
CARE AND CLEANING
When switching off the tower fan, the front
pivot grille cover will rotate automatically
to protect the air outlet grille. This will
help to keep the air outlet grille clean. Wait
until the front pivot grille cover is fully
closed before switching off at the power
outlet. Unplug from the power outlet prior
to cleaning the base, grilles, housing, water
container and water inlet basin.
CLEANING EXTERNAL PARTS
To clean the outside of the tower fan, wipe
the exterior with a soft, damp cloth. Never
use an abrasive cleaner.
Ensure all parts of the tower fan are clean
and dry before storing.
CLEANING THE HUMIDIFIER
INTERNAL PARTS
WATER CONTAINER, WATER
CONTAINER CAP & SEAL
• Remove the water container and unscrew
the water container cap with seal.
• It is important to clean the water
container regularly and ensure it is
dry before reassembling and using the
humidifier function.
• To clean, create a vinegar and water solution
of 1-part vinegar to 1-part water, enough to fill
the container about halfway.
• Making sure the water container cap is
replaced on the container, swish the solution
around for a minute, then fill the rest of the
container up with tap water. Leave to sit for
1–2 hours, or even overnight.
• Empty and rinse well with clean water.
WATER INLET BASIN
Build-up of calcification may occur in the
water inlet basin and should be removed and
cleaned to ensure optimum performance.
Remove the water container to clean the
water inlet basin.
• Ensure the water outlet cap remains in place.
If build-up of calcification is present in the
water inlet basin, rinse with a vinegar and
water solution and let soak for 10 minutes.
Remove the water outlet cap and drain the
vinegar water into a drain source. Replace
the water outlet cap. Rinse with clean water
and drain once more.
• With a damp cloth, wipe the tube, mist cover
and water inlet basin (Fig. 3).
• If there is calcification on the surface, soak
a clean cloth with 1:1 parts vinegar and
water solution and repeat the process until
removed. Wipe with a clean, damp cloth.
Fig 3 Tube
Mist Cover
Water inlet
basin
Ensure all parts of the tower fan are dry
before storing.
LTF408_ANZ_IB_D20.indd 18LTF408_ANZ_IB_D20.indd 18 15/7/20 2:14 pm15/7/20 2:14 pm

19
nNOTE:
Do not wash the water inlet basin under a water
faucet to avoid water flowing or splashing into
the internals of the unit, possibly damaging
the internal electrical parts.
STORAGE
When not in use, store the tower fan upright,
in a cool, clean and dry location.
LTF408_ANZ_IB_D20.indd 19LTF408_ANZ_IB_D20.indd 19 15/7/20 2:14 pm15/7/20 2:14 pm

20
Australian Customers
Phone: [phone]
Web: www.breville.com
New Zealand Customers
Phone: [phone]
Web: www.breville.com
Breville Customer Service Centre
Breville, the Breville logo, Breville Home Connect and Mistic 2 in 1
are trademarks of Breville Pty. Ltd. Android is a trademark of Google LLC.
All other brands may be trademarks of their respective owners. Breville’s
products are distributed in New Zealand under license. A.B.N. 98 000 092 928.
Due to continued product improvement, the products illustrated/photographed in this booklet
may vary slightly from the actual product.
LTF408 ANZ – D20
LTF408_ANZ_IB_D20.indd 20LTF408_ANZ_IB_D20.indd 20 15/7/20 2:14 pm15/7/20 2:14 pm