Breville the AirDynamic 3D Connect User manual

Instruction Book - Suits all LPF308 Models
the AirDynamic 3D™Connect

2 3
BREVILLE
RECOMMENDS
SAFETY FIRST
At Breville we are very safety
conscious. We design and
manufacture consumer
products with the safety of you,
our valued customer, foremost
in mind. In addition, we ask
that you exercise a degree
of care and adhere to the
following precautions.
IMPORTANT
SAFEGUARDS
READ ALL INSTRUCTIONS
BEFORE USE AND SAVE
FOR FUTURE REFERENCE
• Carefully read all instructions
before operating the air
circulator for the first time and
save for future reference.
• Remove and safely discard
any packaging material and
promotional labels before
using the air circulator for the
first time.
• To eliminate a choking hazard
for young children, remove and
safely discard the protective
cover fitted to the power plug
of this air circulator.
• When unpacking the air
circulator, check to see you
have received all the items
listed in the parts list, before
discarding the packaging.
• Do not place the air circulator
near the edge of a bench or
table during operation. Ensure
that the surface is level, stable,
clean and free of water and
other substances.
• Always ensure the air circulator
is properly assembled before
use. Follow the instructions
provided in this book.
• This air circulator is intended
for household use only
and not for commercial or
industrial use.
• Use only the charger supplied
with this appliance to recharge
this air circulator.
2 Breville Recommends Safety First
6 Components
7 Control Panel
8 Features
9 Assembly
11 Operation
12 Functions
15 Wi-Fi Connectivity
16 Care, Cleaning & Storage
cContents
• Disconnect the power plug
before dismantling, assembling
or before cleaning and when
the air circulator is not in use.
• Avoid touching moving parts
of the air circulator.
• Never insert fingers, pencils or
any other objects through the
guards whenever the power
plug is connected, in particular
while the air circulator is
switched on.
• The air circulator must not
be used if the guards are not
fastened correctly, according
to instructions provided in
this book.
• When positioning the rear
grille on the motor shaft, always
ensure the carry handle on
the grille is positioned in the
upright position.
• Ensure the fan blade engages
fully onto the shaft. Please note
this may require some force to
ensure it is fully engaged.
• The air circulator must not
be used if the base is not
fastened correctly, according
to the instructions provided in
this book.
• Do not operate in the presence
of explosives and/or flammable
fumes or liquids.
• Do not unplug the air circulator
by pulling on the cord.
• Never carry the air circulator by
the cord or yank to disconnect
from an outlet; instead, grasp
the plug and pull to disconnect.
Do not pull the cord around
sharp edges or corners.
• Allow the fan blade to stop
completely, always switch off
at the power outlet, and then
unplug the air circulator from
the outlet:
−Before attempting to move
the air circulator
−Before cleaning and
maintenance unless
otherwise specified in
this booklet
−Immediately after use.
• To prevent damage to the air
circulator do not use alkaline
cleaning agents when cleaning,
uses a soft cloth and mild
detergent.
• Do not place anything, on
top of the air circulator when
assembled, when in use and
when stored.
• Store the unit out of reach
of children.
• Keep the air circulator
clean. Follow the cleaning
instructions provided in
this book.

4 5
IMPORTANT
SAFEGUARDS
FOR ALL
ELECTRICAL
APPLIANCES
• Fully unwind the power cord
before use.
• Connect only to a 230V or
240V power outlet.
• The appliance must be used on
a properly grounded outlet. If
it is not sure, please consult a
qualified electrician.
• Do not, under any
circumstances, modify the
power plug or use a power
plug adapter.
• Do not place this appliance on
or near a heat source, such as
hot plate, oven or heaters.
• Position the appliance at a
minimum distance of 20cm
away from walls, curtains and
other heat or steam sensitive
materials and provide adequate
space above and on all sides for
air circulation.
• Do not let the power cord hang
over the edge of a bench or
table, touch hot surfaces or
become knotted.
• This appliance is for household
use only. Do not use this
appliance for anything other
than its intended use. Do not
use in moving vehicles or
boats. Do not use outdoors.
Misuse may cause injury.
• The appliance is not
intended for use by persons
(including children) with
reduced physical, sensory
or mental capabilities, or
lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning use
of the appliance by a person
responsible for their safety.
• Children should be supervised
to ensure that they do not play
with the appliance.
• Always turn the appliance to
the OFF position, switch off at
the power outlet and unplug
at the power outlet when the
appliance is not in use.
• Before cleaning, always turn the
appliance to the OFF position,
switch off at the power outlet,
unplug at the power outlet
and remove the power cord, if
detachable, from the appliance
and allow all parts to cool.
• To protect against electric
shock, do not immerse the
power cord, power plug or
appliance in water or any other
liquid or allow moisture to
come in contact with the part,
unless it is recommended in
the cleaning instructions.
• Any maintenance other than
cleaning should be performed
at an authorised Breville
Service Centre.
• It is recommended to regularly
inspect the appliance. To
avoid a hazard, do not use the
appliance if power cord, power
plug or appliance becomes
damaged in any way. Return
the entire appliance to the
nearest authorized Breville
service centre for examination
and / or repair.
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
• The installation of a residual
current device (safety switch)
is recommended to provide
additional safety protection
when using electrical
appliances. It is advisable
that a safety switch with a
rated residual operating
current not exceeding 30mA
be installed in the electrical
circuit supplying the appliance.
See a qualified electrician for
professional advice.
• During electrical storms,
the appliance should be
disconnected from the power
source at the wall socket to
prevent any electrical surges
that may arise during the storm
and which may inadvertently
cause damage to the appliance
and its electronic componentry.

6 7
A. Front grille
B. Pedestal tube
C. Control panel with LED display
D. Anti-topple base
E. Allen Key with Hex and Phillips bit
F. Remote control
G. Rear grille
H. Fan blades
I. Rear grille locking nut
J. Motor shaft
K. Blade cap
L. Motor shaft pin
M. Circulator motor head
N. Power inlet
O. Hexagon screw
P. Power adaptor
Q. Phillips screws (including 1 spare)
OSCOSC
NATURALTIMER TURBO
ECO
FRONT VIEW REAR VIEW
N
I
J
K
G
E
A
C
B
D
F
G
H
I
J
cComponents cControl Panel
A. VERTICAL OSCILLATION
B. HORIZONTAL OSCILLATION
C. TIMER
D. NATURAL MODE
E. POWER ON/OFF
F. SMART ECO MODE
G. UP / WI-FI
H. DOWN
I. TURBO SPEED
J. LED DISPLAY
H
A
C
B
D
P
O
Q
F
E
L
M

8 9
FFeatures
WHAT IS AN AIR CIRCULATOR?
Traditional fans will move air that is directly
in contact with them, pulling air from behind
to the front, with the benefit of cooling being
felt only when directly facing you. Usually
traditional fans are only used during the
warmer months.
Air circulators on the other hand, work to keep
all air in a room in motion, moving around
constantly and creating an air circulation
pattern that will make the whole room
more comfortable.
By using a 3D air circulation, your Breville air
circulator ensures constant movement of the
air in the room, reducing cold and warm spots
that are found in many rooms.
By circulating both stale indoor air and fresh
outdoor air (from open windows), Breville air
circulators also work on improving ventilation.
The Breville pedestal air circulator is perfect to
use all year round, as it regulates temperature,
clears stuffy air and creates a safe environment
for the whole family.
WHERE TO POSITION YOUR
AIR CIRCULATOR
WARMER MONTHS:
Cool air tends to sink to the floor. During
warm weather, point the air circulator
facing towards a wall on high speed, angled
halfway between the ceiling and floor. The
circulator will efficiently cool the room down
by forcing the cool air to move, creating air
circulation patterns.
When using an air conditioner, point the air
circulator from the back of the room towards
the bottom of the air conditioner at a 30° angle
to intensify the cool air and distribute the
cool air faster and more efficiently around the
room. Use the horizontal oscillation for even
better distribution.
COLD AIR
COOLER MONTHS:
Warm air naturally rises towards the ceiling.
When using a heater, the warm air produced
will move up. Point the air circulator fan up at
a 90° angle.
By pointing the air circulator upwards, the
hot air will circulate with the cooler air near
the floor, resulting in better distribution of
room temperature.
aAssembly
BEFORE FIRST USE
Before using your Breville pedestal air
circulator for the first time, remove all
packaging material and promotional labels.
Check for any missing or damaged parts as per
the components list.
wIMPORTANT:
When unpacking the air circulator, check
to see you have received all the items listed
in the components list, before discarding
the packaging.
ASSEMBLING THE PEDESTAL STAND
AND BASE
1. Align the connector on the bottom of
the pedestal tube with the connector on
the top of the anti-topple base and push
together (Fig 1).
Fig 1
2. Safely turn the assembled anti-topple
base on its side and securely tighten the
assembly using the hexagon screw and the
Allen key provided (Fig 2). Return the unit
back to an upright position.
Fig 2
ASSEMBLING THE AIR
CIRCULATOR HEAD
1. Remove the blade cap from the motor shaft
by turning clockwise. Remove the rear grille
locking nut by turning it counter-clockwise
(Fig 3).
Fig 3
2. Separate the front grille by turning the front
grille counter-clockwise (Fig 4). Remove
packaging and the fan blade and put aside.
Fig 4

10 11
oOperation
OPERATING YOUR BREVILLE
AIR CIRCULATOR
1. Place the air circulator on a flat surface. Use
the Where to Position Your Air Circulator
section in this book for positioning
depending on requirements.
2. Insert the power plug into a 230V or 240V
power outlet and switch the power outlet on.
The LED display will illuminate to display
the current room temperature. The air
circulator is now in standby mode.
3. Touch the button to turn the air
circulator on. The air circulator will
automatically start in NORMAL mode at
fan speed 1.
nNOTE:
To return to standby mode at any time during
operation, touch the button.
wCAUTION:
Never insert fingers, pencils or any other
objects through the guards whenever the
power plug is connected, in particular while the
air circulator is switched on.
ROOM AMBIENT TEMPERATURE
Your Breville Air Circulator is fitted with a
temperature sensor that detects the room
temperature which will display through the
LED display. The figure displayed is only an
indication of the room temperature and will
vary depending on the location of the air
circulator in the room.
The LED display shows ambient temperature
only, or cycles to show the ambient
temperature and the setting depending on the
selected mode.
3. To place the rear grille onto the motor head,
align the motor head with the locating tab
on the rear grille. Ensure the upward arrow
mark on the motor head aligns with the
upward arrow mark on the rear grille.
4. Refit the rear grille locking nut and secure
the rear grille by turning the locking nut
clockwise (Fig 5). Make sure the rear grille
has not slipped off the locating pins before
tightening. This should be done by hand.
Do not use force to secure.
Fig 5
5. Align the grooves found at the back centre
of the blade with the motor shaft pin and
push all the way down.
nNOTE
The back of the blade can be distinguished
from the front by a distinctive O symbol found
on the blade fin.
6. Refit and secure the blade cap onto the
motor shaft by turning counter-clockwise
(Fig 6). This should be done by hand. Do
not use force.
Fig 6
7. Place the front grille onto the rear grille
so that the left line mark on the top of the
rear grille is aligned with the line mark
on the front grille. Turn clockwise to lock
into place.
HINT:
Once the front and rear grilles are assembled
correctly, the Breville logo will be straight.
8. Securely tighten the assembled grilles
using the Phillips screw and the Allen key
provided (Fig 7).
TIGHTEN
Fig 7
9. Connect the power adaptor into the power
inlet found on the anti-topple base. The air
circulator is now ready for use.

12 13
oFunctions
MODE
This Breville AirDynamic 3D™ Connect air
circulator has 4 modes: NORMAL, TURBO,
NATURAL and SMART ECO. The air
circulator will start automatically on NORMAL
mode on speed 1 once it is switched on.
NORMAL MODE
NORMAL mode has 8 fan speed settings;
setting 1 for lowest fan speed up to setting 8 for
the highest fan speed. To choose a fan speed,
touch the or buttons until the desired
speed number is reached and the speed will
adjust automatically.
NORMAL mode is the default mode settings
for this air circulator. In NORMAL mode, none
of the buttons NATURAL, SMART ECO or
TURBO illuminate on the control panel.
TURBO MODE
TURBO mode creates extra comfort on a hot
day. On TURBO mode, the air circulator will
run at the highest speed (8) automatically.
Touch the button and the light will
illuminate to indicate it is activated.
NATURAL MODE
Continuous air flow can create a chilling
effect on the skin and a discomfort when
exposed for too long. NATURAL mode
generates a gentle breeze to maintain body
temperature, by simulating a wind blowing
rhythm, automatically alternating wind speeds
according to pre-programed cycles. NATURAL
mode has 3 variations.
When the unit is on, to activate NATURAL
mode, touch the button. The light will
illuminate on the NATURAL button on the
control panel and the default NATURAL cycle
program 1 (n1) will display on the LED display.
The fan speed will operate automatically
according to the natural cycle 1 (n1) program.
To select NATURAL cycle program 2 (n2) and
NATURAL cycle program 3 (n3), touch the
button and ‘n2’ and ‘n3’ will display respectively.
To stop NATURAL mode and return to
NORMAL mode, touch the button until no
lights illuminate on the NATURAL button on
the control panel.
Diagram showing NATURAL cycle programs:
Program 1 (n1)
4
7
1
OFF
Program 2 (n2)
OFF
4
7
1
Program 3 (n3)
OFF
4
7
1
1 = Low speed, 4 = Medium speed, 7 = High speed
SMART ECO MODE
SMART ECO mode will automatically adjust
the fan speed depending on the ambient room
temperature. This program delivers the optimal
cycle to save energy and operate quietly and
efficiently, when possible. SMART ECO mode
is ideal to use during sleep or when left on for a
long period of time.
When the unit is on, to activate SMART ECO
mode, touch the button and the light will
illuminate on the button.
The air circulator will automatically adjust
the fan speed based on the following
programmed rules.
Ambient T (°C) Air circulator speed
< 26 Speed 1
26 – 28 Cycle between speed 2,
speed 3 and speed 4.
Operation for 5 secs
on each speed.
29 – 34 Cycle between speed 5,
speed 6 and speed 7.
Operating for 5 secs on
each speed.
> 35 Speed 8
nNOTE:
Fan speed in this mode cannot be manually
adjusted.
To stop SMART ECO mode and return to
NORMAL mode, touch the button until no
light illuminates on the button.
AUTO-OFF TIMER
The Breville Air Circulator comes with a
12-hour auto-off timer that can be set in one-
hour intervals. To set the timer, press the
button until the desired hour is displayed on
the display screen. Once the timer icon stops
flashing, the timer will be set. The timer will
start on the selected mode, and the selected
speed and will stop automatically once the
time has elapsed.
To set the timer, press the button repeatedly
until the desired number of hours is displayed
on the LED display. Light flashes on the
TIMER button on the control panel during
setting and the light flashing will stop when
timer is set.
The auto-off timer will start on the selected
mode and will stop automatically once the
time has elapsed. The LED display will display
the set circulator mode once the auto-off timer
begins. To check the pre-set time left on the
LED display, touch the button once.
nNOTE:
The display will revert back to the current room
temperature. To display the remaining time,
press the TIMER button once.
To cancel the auto off time anytime, press
the button until ‘0’ is displayed on the
LED display and the green light above the
TIMER button no longer illuminates within a
few seconds.
nNOTE
• To run the air circulator continuously, do not
set the timer or set the timer to ‘0’.
• All modes can be adjusted at any time after
the timer is set.
• The air circulator will stop and switch to
standby mode once the set time has elapsed.
OSCILLATION AND
3D AIR CIRCULATION
The Breville Air Circulator can oscillate left to
right and up and down. The oscillations can be
set on any MODE.
To activate the left to right oscillation, touch
the button once. The air circulator will move
left to right continuously.
To activate the up and down oscillation, touch
the button once. The air circulator will start
to move up and down continuously.
To achieve 3D air circulation, activate both
horizontal and vertical oscillations. This will set
a unique air circulation pattern.
When the air circulator is turned off, it returns
to its initial position automatically.
To set the orientation of your air circulator,
touch the respective oscillation button
again. The oscillator will stay at your
preferred position.

14 15
Wi-Fi
Connectivity
SET UP YOUR AIR CIRCULATOR
1. Ensure the mobile device is connected to a
home Wi-Fi network.
2. The air circulator must be on standby mode.
Once on standby, the symbol will flash
fast on the display panel. The air circulator
is now ready to connect.
3. Log into your Breville Home Connect™ app
account and stay on the “Home” page. To
add the air circulator to the list, touch ‘Add
Device’ or the symbol found in the top
right-hand corner of the screen. Follow the
prompts in the app.
4. If the connection is successful, the air
circulator will appear in the main page of
the app and the symbol light on the air
circulator will illuminate.
5. If connection is unsuccessful, touch and
hold the button for 5 seconds until the
symbol is flashing slowly. Follow the
prompts in the app to connect in a different
mode.
The AirDynamic 3D™ Connect air circulator
can offer remote operation by using a home
Wi-Fi connection and the Breville Home
Connect™ app downloaded to a compatible
mobile phone through the Google Play store or
Apple App store.
To go straight to the appropriate app store,
Scan the QR code below.
For instructions on how to use the app, scan
the QR code below, refer to the Quick Start
Guide that can be found in the box or go to:
tinyurl.com/HomeConnectQuickStart
nNOTE
The Breville Home Connect™ app is compatible
with mobile phones running Android® 5.0 or
later and iOS devices 9.0 or later.
nNOTE
To control the air circulator using the app, the
air circulator must be plugged in to an active
power outlet.
REMOTE CONTROL
The Breville air circulator comes with a remote
control. This remote control features the same
buttons as the control panel (except the Wi-Fi
function) on the air circulator and can be used
the same way.
The remote control includes 1 x CR2032
3V Lithium battery. This Lithium battery is
protected by an isolating slip. Before first
using the remote control, remove the battery
isolating slip by pulling the slip outwards away
from the remote control.
To check and/or to replace the battery, open
up the battery compartment at the back of the
remote by forming a good grip of the remote,
pushing the small arched groove to the right
and simultaneously pushing out the battery
compartment cover by pushing the rectangular
groove outwards (Fig 1a). Insert the battery
paying attention to the polarity (+ and -).
Fig 1a
Reinsert the battery compartment into the
remote control ensuring that the + symbol
is facing upwards when inserted (Fig 1b).
Make sure the battery compartment is
correctly secured.
Fig 1b
nNOTE:
To use the remote control, it must be pointed at
the control panel and must be used within five
meters of the unit.
wWARNING
KEEP BATTERIES OUT OF REACH
OF CHILDREN
Swallowing may lead to serious injury in as
little as 2 hours or death, due to chemical burns
and potential perforation of the oesophagus.
If you suspect your child has swallowed or
inserted a button battery immediately call the
24-hour Poisons Information Centre on 13 11
26 for fast, expert advice. Examine devices
and make sure the battery compartment is
correctly secured, e.g. that the screw or other
mechanical fastener is tightened. Do not use if
compartment is not secure.
Dispose of used button batteries immediately
and safely. Flat batteries can still be dangerous.
Tell others about the risk associated with
button batteries and how to keep their
children safe.

16 17
fNotes C
Care, Cleaning
& Storage
CARE AND CLEANING
Always switch the Breville air circulator off.
Switch off at the power outlet and unplug from
the power outlet prior to cleaning the motor
head, pedestal tube, anti-topple base, grilles
and fan blades.
To clean the outside of the air circulator, wipe
the exterior with a soft, damp cloth. Never use
an abrasive cleaner. To clean the fan blades and
remove dust that may have accumulated, use a
soft, damp cloth or a vacuum cleaner with the
brush attachment.
If access to the fan blades is required, loosen
the front and rear grilles screw then unlock
the front grille from the rear grille. Always
reassemble correctly before using.
STORAGE
When not in use, store the air circulator
upright in a cool, clean and dry location.

18 19
fNotes fNotes

Australian Customers
Phone: [phone]
Web: www.breville.com
New Zealand Customers
Phone: [phone]
Web: www.breville.com
Breville Customer Service Centre
Breville, the Breville logo, AirDynamic 3D and Breville Home Connect are trademarks of Breville Pty. Ltd.
Android is a trademark of Google LLC. All other brands may be trademarks of their respective owners.
Breville’s products are distributed in New Zealand under license. A.B.N. 98 000 092 928.
Due to continued product improvement, the products illustrated/photographed in this booklet
may vary slightly from the actual product.
LPF308 ANZ – C20