Briggs & Stratton P2200 User manual

Not for
Reproduction
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC
MILWAUKEE, WISCONSIN, U.S.A. Manual No. 80012873 Revision B
Inverter Generator
Operator’s Manual
This generator is rated in accordance with CSA (Canadian Standards Association)
standard C22.2 No. 100-14 (motors and generators).

Not for
Reproduction
Thank you for purchasing this quality-built Briggs & Stratton® generator. We are pleased that you’ve placed your
confidence in the Briggs & Stratton brand. When operated and maintained according to the instructions in this
manual, your Briggs & Stratton generator will provide many years of dependable service.
This manual contains safety information to make you aware of the hazards and risks associated with generators
and how to avoid them. This generator is designed and intended only for supplying electrical power for operating
compatible electrical lighting, appliances, tools and motor loads, and is not intended for any other purpose. It is
important that you read and understand these instructions thoroughly before attempting to start or operate this
equipment. Save these original instructions for future reference.
This generator requires final assembly before use. Refer to the Assembly section of this manual for
instructions on final assembly procedures. Follow the instructions completely.
Where to Find Us
You never have to look far to find Briggs & Stratton support and service for your generator. Consult your Yellow
Pages. There are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality service.
You can also contact Briggs & Stratton Customer Service by phone at 1800 356 632(AUS) or 0800-484-282(NZ),
or on the Internet at BRIGGSandSTRATTON.com.au.
Generator
Model Number _______________________
Revision _____________________
Serial Number __________________
Date Purchased _____________________
Table of Contents
Operator Safety....................... 3
Assembly............................ 7
Features and Controls ................ 10
Operation........................... 13
Maintenance ........................ 17
Troubleshooting ..................... 22
Warranty ........................... 23
Product Specifications ................ 24
Common Service Parts ............... 24
Copyright © 2016. Briggs & Stratton Power Products Group, LLC
Milwaukee, WI, USA. All rights reserved.
BRIGGS & STRATTON POWER PRODUCTS is a registered
trademark of Briggs & Stratton Corporation
Milwaukee, WI, USA

Not for
Reproduction
3
Operator Safety
Safety Labels
The generator safety labels shown below and on the next page are placed on your portable generator to draw
attention to potential safety hazards.

Not for
Reproduction
4 BRIGGSandSTRATTON.com.au
Equipment Description
Read this manual carefully and become
familiar with your generator. Know its
applications, its limitations and any hazards
involved.
The generator is an engine–driven, revolving field,
alternating and direct current (AC & DC) generator. It
was designed to supply electrical power for operating
compatible electrical lighting, appliances, tools and motor
loads. The generator’s revolving field is driven at about

switch off) by a single-cylinder engine.
NOTICE Exceeding generators wattage/amperage
capacity can damage generator and/or electrical
devices connected to it.
• DO NOT exceed the generator’s wattage/amperage
capacity. See Generator Capacity.
Every effort has been made to ensure that the
information in this manual is both accurate and current.

change, alter or otherwise improve the generator and
this documentation at any time without prior notice.
Important Safety Information
The manufacturer cannot possibly anticipate every
possible circumstance that might involve a hazard.
The warnings in this manual, and the tags and decals
affixed to the unit are, therefore, not all-inclusive.
If you use a procedure, work method or operating
technique that the manufacturer does not specifically
recommend, you must satisfy yourself that it is safe
for you and others. You must also make sure that the
procedure, work method or operating technique that
you choose does not render the generator unsafe.
Safety Symbols and Meanings
The safety alert symbol indicates a potential
personal injury hazard. A signal word (DANGER,
WARNING, or CAUTION) is used with the alert symbol
to designate a degree or level of hazard seriousness. A
safety symbol may be used to represent the type of
hazard. The signal word NOTICE is used to address
practices not related to personal injury.
DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
WARNING indicates a hazard which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazard which, if not
avoided, could result in minor or moderate injury.
NOTICE indicates information considered important,
but not hazard-related.
Explosive Pressure Chemical Burn
Fire Explosion
Toxic Fumes

Moving Parts
Electrical Shock
Kickback
Flying Objects
Operator’s Manual
Carbon
Monoxide Alarm
On
Ground Terminal
Floating
Neutral
Off Fuel
Choke Run Suffication

Not for
Reproduction
5
WARNING Storage batteries give off explosive
hydrogen gas during recharging.

a long time after battery has been
charged. Slightest spark could ignite hydrogen
causing explosion resulting in death or serious
injury.
Battery electrolyte fluid contains acid and is
extremely caustic. Contact with battery fluid could
cause chemical burns resulting in serious injury.
• DO NOT allow any open flame, spark, heat, or lit
cigarette during and for several minutes after charging a
battery.
• Wear protective goggles, rubber apron, and rubber
gloves.
• DO NOT continue to charge a battery that becomes hot
or is fully charged.
• DO NOT leave battery unattended.
WARNING Fuel and its vapors are extremely
flammable and explosive which
could cause burns, fire or explosion
resulting in death or serious injury.
WHEN ADDING OR DRAINING FUEL
• Turn generator engine OFF and let it cool at least 2
minutes before removing fuel cap. Loosen cap slowly to
relieve pressure in tank.
• Fill or drain fuel tank outdoors.
• DO NOT overfill tank. Allow space for fuel expansion.
• If fuel spills, wait until it evaporates before starting engine.
• Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
• Check fuel lines, tank, cap and fittings frequently for
cracks or leaks. Replace if necessary.
• DO NOT light a cigarette or smoke.
WHEN STARTING EQUIPMENT
• Ensure spark plug, muffler, fuel cap, and air cleaner are
in place.
• DO NOT crank engine with spark plug removed.
WHEN OPERATING EQUIPMENT
• DO NOT operate this product inside any building,
carport, porch, mobile equipment, marine applications, or
enclosure.
• DO NOT tip engine or equipment at angle which causes
fuel to spill.
• DO NOT stop engine by moving choke control to
( ) position.
WHEN TRANSPORTING, MOVING OR REPAIRING
EQUIPMENT
• Transport/move/repair with fuel tank EMPTY or with fuel
shutoff valve OFF (0).
• DO NOT tip engine or equipment at angle which causes
fuel to spill.
• Disconnect spark plug wire.
WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN
TANK
• Store away from furnaces, stoves, water heaters, clothes
dryers, or other appliances that have pilot light or other
ignition source because they could ignite fuel vapors.
WARNING Starter cord kickback (rapid
retraction) will pull hand and arm toward
engine faster than you can let go which
could cause broken bones, fractures,
bruises, or sprains resulting in serious injury.
• When starting engine, pull cord slowly until resistance is
felt and then pull rapidly to avoid kickback.
• NEVER start or stop engine with electrical devices
plugged in and turned on.
WARNING 
Engine exhaust contains carbon monoxide,
a poisonous gas that could kill you in
minutes. You CANNOT smell it, see it, or
taste it. Even if you do not smell exhaust fumes, you
could still be exposed to carbon monoxide gas.
• Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
• DO NOT run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors
and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for hours,
even after this product has shut off.
• ALWAYS place this product downwind and point the
engine exhaust away from occupied spaces.
If you start to feel sick, dizzy, or weak while using this

may have carbon monoxide poisoning.

Not for
Reproduction
6 BRIGGSandSTRATTON.com.au
NOTICE Exceeding generators wattage/amperage
capacity could damage generator and/or electrical
devices connected to it.
• DO NOT exceed the generator’s wattage/amperage
capacity. See Generator Capacity.
• Start generator and let engine stabilize before
connecting electrical loads.
• Connect electrical loads in OFF position, then turn
ON for operation.
• Turn electrical loads OFF and disconnect from
generator before stopping generator.
NOTICE Improper treatment of generator could
damage it and shorten its life.
• Use generator only for intended uses.
• If you have questions about intended use, ask dealer
or contact local service center.
• Operate generator only on level surfaces.
• DO NOT expose generator to excessive moisture,
dust, dirt, or corrosive vapors.
• DO NOT insert any objects through cooling slots.
• If connected devices overheat, turn them off and
disconnect them from generator.
• Shut off generator if:
-electrical output is lost;
-equipment sparks, smokes, or emits flames;
-unit vibrates excessively.
WARNING Starter and other rotating parts
could entangle hands, hair, clothing, or
accessories resulting in serious injury.
• NEVER operate generator without protective housing or
covers.
• DO NOT wear loose clothing, jewelry or anything that
could be caught in the starter or other rotating parts.
• Tie up long hair and remove jewelry.
CAUTION Excessively high operating speeds
could result in minor injury.
Excessively low operating speeds impose a heavy
load.
• DO NOT tamper with governor spring, links or other parts
to increase engine speed. Generator supplies correct
rated frequency and voltage when running at governed
speed.
• DO NOT modify generator in any way.
WARNING Generator voltage could cause
electrical shock or burn resulting in death or
serious injury.
• DO NOT connect generator to a building’s electrical
system.
• DO NOT touch bare wires or receptacles.
• DO NOT use generator with electrical cords which are
worn, frayed, bare or otherwise damaged.
• DO NOT operate generator in the rain or wet weather.
• DO NOT handle generator or electrical cords while
standing in water, while barefoot, or while hands or feet
are wet.
• DO NOT allow unqualified persons or children to operate
or service generator.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage
fuel tank causing a fire, resulting in
death or serious injury.
Contact with muffler area could cause burns
resulting in serious injury.
• DO NOT touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 1.5 m (5 ft.) of clearance on all sides of
generator including overhead.
• Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
• Replacement parts must be the same and installed in the
same position as the original parts.
WARNING Unintentional sparking could cause
fire or electric shock resulting in
death or serious injury.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR
GENERATOR
• Disconnect the spark plug wire from the spark plug and
place the wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
• Use approved spark plug tester.
• DO NOT check for spark with spark plug removed.

Not for
Reproduction
7
Assembly
Your generator requires some assembly and is ready
for use after it has been properly serviced with the
recommended fuel and oil.
If you have any problems with the assembly of your
generator, please call the generator helpline at 1800
356 632(AUS) or 0800-484-282(NZ).If calling for
assistance, please have the model, revision, and serial
number from the identification label available. See
Features and Controls for identification label location.
Unpack Generator
1. Set the carton on a rigid, flat surface.
2. Remove everything from carton except generator.
3. Open carton completely by cutting each corner
from top to bottom.
The generator is supplied with:
• Battery charge cables
• Operator’s manual
• Engine oil bottle
• Tool kit
• Funnel
Add Engine Oil
1. Place generator on a level surface.
2. Loosen the two maintenance cover screws and
remove the side maintenance cover.
3. Clean area around oil fill and remove yellow oil fill
cap.
4. Using oil funnel, slowly pour contents of provided
oil bottle into oil fill opening to the point of
overflowing at oil fill cap.
NOTICE Improper treatment of generator could
damage it and shorten its life.
• DO NOT attempt to crank or start the engine before it has
been properly serviced with the recommended oil. This
could result in an engine failure.
5. Replace oil fill cap and fully tighten.
6. Replace the maintenance cover and hand tighten
the two maintenance cover screws.
Add Fuel
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline.
• A minimum of 87 octane/87 AKI (91 RON). For
high altitude use, see High Altitude.
• Gasoline with up to 10% ethanol (gasohol) is
acceptable.
NOTICE Use of unapproved fuels could damage
generator and voids warranty.
• DO NOT use unapproved gasoline such as E15 and E85.
• DO NOT mix oil in gasoline or modify engine to run on
alternate fuels.
To protect the fuel system from gum formation, mix in a
fuel stabilizer when adding fuel. See Storage. All fuel is
not the same. If you experience starting or performance
problems after using fuel, switch to a different fuel
provider or change brands. This engine is certified to
operate on gasoline. The emission control system for this
engine is EM (Engine Modifications).
1. Clean area around fuel fill cap, remove cap.
2. Slowly add unleaded fuel to red fuel level indicator (A)
in fuel tank. Be careful not to fill above the indicator.
This allows adequate space for fuel expansion.
3. Install fuel cap and let any spilled fuel evaporate
before starting engine.
WARNING Fuel and its vapors are extremely
flammable and explosive which could
cause burns, fire or explosion
resulting in death or serious injury.
WHEN ADDING FUEL
• Turn generator engine OFF and let it cool at least 2 minutes
before removing fuel cap. Loosen cap slowly to relieve
pressure in tank.
• Fill fuel tank outdoors.
• DO NOT overfill tank. Allow space for fuel expansion.
• If fuel spills, wait until it evaporates before starting engine.
• Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
• Check fuel lines, tank, cap and fittings frequently for
cracks or leaks. Replace if necessary.
• DO NOT light a cigarette or smoke.
A

Not for
Reproduction
8 BRIGGSandSTRATTON.com.au
High Altitude
At altitudes over 1524 m (5,000 ft.), a minimum
85 octane / 85 AKI (89 RON) gasoline is acceptable.
To remain emissions compliant, high altitude
adjustment is required. Operation without this
adjustment will cause decreased performance,
increased fuel consumption, and increased emissions.
See a Briggs & Stratton Authorized Dealer for high
altitude adjustment information. Operation of the
engine at altitudes below 762 m (2,500 ft.) with the
high altitude kit is not recommended.
Grounding Fastener
The generator neutral is floating, which means that
the AC stator winding is isolated from the grounding
fastener and the AC receptacle ground pins. On a
floating neutral generator the AC receptacle ground
pins are not functional. Electrical devices, such as a
residual current device (RCD), requiring a functioning
AC receptacle ground pin will not operate.
Special Requirements
There may be Federal, local codes, or ordinances that
apply to the intended use of the generator. Please
consult a qualified electrician, electrical inspector, or
the local agency having jurisdiction:
• This generator has a floating neutral and is not for
use on job sites requiring a bonded neutral.
Portable Generator Location
Before starting the portable generator there are two
equally important safety concerns regarding carbon
monoxide poisoning and fire that must be addressed.
Operation Location to Reduce the Risk of Carbon
Monoxide Poisoning
All fossil fuel burning equipment, such as a portable
generator, contains carbon monoxide gas in the engine
exhaust, a poisonous gas that could kill you in minutes.
You cannot smell it, see it, or taste it. Even if you do
not smell exhaust fumes, you could still be exposed to
carbon monoxide gas.
By law it is required in many states to have a carbon
monoxide alarm (A) in operating condition in your
home. A carbon monoxide alarm is an electronic
device that detects hazardous levels of carbon
monoxide. When there is a buildup of carbon
monoxide, the alarm will alert the occupants by
flashing visual indicator light and alarm. Smoke alarms
cannot detect carbon monoxide gas.
A
WARNING 
Engine exhaust contains carbon monoxide,
a poisonous gas that could kill you in
minutes. You CANNOT smell it, see it, or
taste it. Even if you do not smell exhaust fumes, you
could still be exposed to carbon monoxide gas.
• Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
• DO NOT run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors
and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for hours,
even after this product has shut off.
• ALWAYS place this product downwind and point the
engine exhaust away from occupied spaces.
If you start to feel sick, dizzy, or weak while using this

You may have carbon monoxide poisoning.
Install carbon monoxide alarms inside
your home. Without working carbon
monoxide alarms, you will not realize
you are getting sick and dying from
carbon monoxide poisoning.
CARBON MONOXIDE ALARM(S)
USE OUTDOORS - AVOID CARBON MONOXIDE POISONING
point away
from home
MUFFLER

Not for
Reproduction
9
Operation Location of Portable Generator to
REDUCE THE RISK OF FIRE
5 ft.
(1.5 m) min.
MUFFLER
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage fuel tank
causing a fire, resulting in death or serious
injury.
• Portable generator must be at least 1.5 m (5 ft.) from
any structure, overhang, trees, windows, doors, any wall
opening, shrubs, or vegetation over 30.5 cm (12 in.) in
height.
• DO NOT place portable generator under a deck or other
type of structure that may confine airflow.
• Smoke alarm(s) MUST be installed and maintained
indoors according to the manufacturer’s instructions/
recommendations. Carbon monoxide alarms cannot
detect smoke.
• DO NOT place portable generator in manner other than
shown.
5 ft. (1.5 m) min.

Not for
Reproduction
10 BRIGGSandSTRATTON.com.au
Features and Controls
Read this Operator’s Manual and safety rules before operating your generator.
Compare the illustrations with your generator, to familiarize yourself with the locations of various controls
and adjustments. Save this manual for future reference.
F
E
M
K
A
G
N
P
L
J
H
C
B
D
R
A - Fuel Tank — Capacity of 5.7 L (1.5 U.S. gallons).
B - Choke Lever — Used when starting a cold engine.

— Use this switch to turn the QPT on and off.
D - Side Maintenance Cover — Remove to gain
access to the air cleaner and oil service.
E - Recoil Starter — Used to start the engine
manually.
F - 12 Volt DC Receptacle — Use this receptacle with
battery charge cables to charge a 12 Volt battery.
This receptacle is protected by a push to reset
circuit breaker.
G - Engine Switch — Set this switch to ON (I) before
using recoil starter. Set switch to OFF (0) to stop
engine. Also turns fuel valve on and off.
H - 230 Volt AC, 15 Amp Receptacles — May be
used to supply electrical power for the operation

electrical, lighting, appliance, tool, and motor loads.
J - Retractable Handle — Press button and pull
handle out to move generator. Press button to push
handle back in.
K - USB Port — Use this port to recharge any USB
powered device.
L - Parallel Operation Port — Use this port with
optional parallel operation kit to allow two
generators to run in parallel.
 — Built in LCD screen
to monitor certain features on the generator. See
STATSTATION™.
N - Grounding Fastener — Consult your local agency
having jurisdiction for grounding requirements in
your area.
P - Spark Arrester Muffler — Exhaust muffler lowers
engine noise and is equipped with a spark arrester
screen.
R - Top Maintenance Cover — Remove to gain
access to the spark plug.
Items Not Shown:
Air Cleaner (under side maintenance cover) —
Protects engine by filtering dust and debris out of
intake air.
Identification Label — Provides model, revision, and
serial number of generator. Please have these readily
available when calling for assistance.
Oil Fill Cap (under side maintenance cover) —
Check and add engine oil here.

Not for
Reproduction
11
Cord Sets and Receptacles
Use only high quality, well-insulated, grounded
extension cords with the generator’s receptacles.
Inspect extension cords before each use.
Check the ratings of all extension cords before you use
them. Extension cord sets used should be rated for AC
loads 15 Amps or greater. Check operator’s manuals
of devices to be powered for the manufacturer’s
recommendations.
Keep extension cords as short as possible to minimize
voltage drop.
230 Volt AC, 15 Amp Receptacles
These receptacles are protected against overload by
an internal overload system.
Use receptacles to operate 230 Volt AC, single–

watts (2.6 kW) at 11.3 Amps of current. Use cord sets
that are rated for 230 Volt AC loads at 15 Amps (or
greater).
NOTICE Receptacles may be marked with rating
value greater than generator output capacity.
• NEVER attempt to power a device requiring more
amperage than generator or receptacle can supply.
• DO NOT overload the generator. See Generator Capacity.
5 Volt DC USB Port
The maximum current available for the USB port is 1
Amp at 5 Volts. The USB port allows you to recharge
any USB powered device with a USB charging cable
(not included).
NOTICE For charging ITE (Information Technology
Equipment) only.
12 Volt DC Receptacle
The maximum current available for the battery charge
circuit is 5 Amps. A DC circuit breaker protects this
receptacle from overloads. If an overload occurs, the
circuit breaker will trip (push button pops out). Wait a
few minutes and push the button in to reset the circuit
breaker.
This receptacle allows you to recharge a 12 Volt
automotive or utility style storage battery with the
battery charge cable provided.
This receptacle can not be used to crank an engine
having a discharged battery. See Charging a Battery
before attempting to recharge a battery.
NOTICE When using the battery charge circuit and
USB port, turn the QPT switch to the OFF (0) position.
Parallel Operation Port
The parallel operation port allows you to connect two
model inverter generators with an Briggs & Stratton
approved parallel operation kit (optional equipment).
When running in parallel, the total output of power is up
to 4,800 watts (4.8 kW).
Models Maximum Output
P2200 & P2200 3000 Watts
P2200 & P3000 3000 Watts
P3000 & P3000 4800 Watts
WARNING Damaged or overloaded electrical
cords could overheat, arc, and burn
resulting in death or serious injury.
• ONLY use cords rated for your loads.
• Follow all safeties on electrical cords.
• Inspect cord sets before each use.

Not for
Reproduction
12 BRIGGSandSTRATTON.com.au

The control panel has a built in LCD display (A) to
monitor the following features:
• Load Monitor (Total Generator Load)
  
• Maintenance Reminder (Engine Maintenance)
Load Monitor
The load monitor measures the output wattage
(generator load) of all the generator receptacles and
will display the percentage of total generator load.
Hour Meter
The LCD on the control panel also has a built in hour
meter that displays and records how many hours your
generator has run (up to 999.9).
Maintenance Reminder
The LCD on the control panel also has a built in
maintenance reminder to alert you to change air filter,
change oil, and change spark plug. The LCD display
will flash both the load percentage and the hour display
every 50 hours for the different maintenance intervals.
See Maintenance Schedule for different maintenance
intervals.
Pressing the “View” button (B) will toggle between the
flashing load percentage and the flashing hour display.
Once maintenance has been performed, you must
push and hold the “View” button on the control panel
for a minimum of 3 seconds to stop the display from
flashing and return it to normal operation.
Output Indicator
The green LED output indicator light (C) comes
on when the generator is operating normally. It
indicates that the generator is producing power at the
receptacles.
Overload Alarm
The red LED overload alarm light (D) comes on and
cuts power to the receptacles if you overload the
generator. The green output indicator light will also go
off. If the generator was overloaded, you must turn off
and unplug all electrical loads, press the “Reset” button
(E) on the generator control panel and then plug in
and restart electrical loads one at a time to continue in
normal operating mode.
Low Oil Indicator
The low oil indicator system is designed to prevent
engine damage caused by not enough engine oil. If the
engine oil level drops below a preset level, the yellow
LED low oil indicator light (F) comes on and an oil level
switch will stop the engine. If the engine stops or the
yellow LED low oil indicator light comes on when you
pull the recoil handle, check the engine oil level.
D
F
A
E
C
B

Not for
Reproduction
13
Operation
Starting the Engine
Disconnect all electrical loads from the generator. Use
the following start instructions:
1. Make sure unit is on a level surface.
NOTICE Failure to start and operate the unit on a
level surface could cause the unit not to start or shut
down during operation.
2. Turn the engine switch (A) to the ON (I) position.
3. Push choke lever (B ) position.
NOTICE To help start the engine for the very first
time, after running out of fuel or after a long period of
storage, fill fuel tank as described in Add Fuel. It will
require more than several start attempts until the air in
the fuel system has been purged.
4A. Grasp recoil handle and pull slowly until slight
resistance is felt. Then pull rapidly to start engine.
• If engine starts, proceed to step 6.
• If engine fails to start, proceed to step 5.
To start engine thereafter:
4B. Grasp recoil handle and pull slowly until slight
resistance is felt. Then pull rapidly one time only to
start engine.
• If engine starts, proceed to step 6.
• If engine fails to start, proceed to step 5.
5. Move choke lever to half choke position, and pull
recoil handle twice.
• If engine fails to start, repeat steps 3 thru 4.
6. Slowly move choke lever to RUN ( ) position. If
engine falters, move choke lever to half choke
position until engine runs smoothly, and then to
RUN ( ) position.
NOTICE If engine floods, move choke lever to
RUN ( ) position and crank until engine starts.
NOTICE If engine starts after 2 pulls but fails to run,
or if unit shuts down during operation, make sure unit
is on a level surface and check for proper oil level
in crankcase. This unit is equipped with a low oil
protection device. If so, oil must be at proper level for
engine to start.
A
B
WARNING Starter cord kickback (rapid
retraction) will pull hand and arm toward
engine faster than you can let go which
could cause broken bones, fractures,
bruises, or sprains resulting in serious injury.
• When starting engine, pull cord slowly until resistance is
felt and then pull rapidly to avoid kickback.
•NEVER start or stop engine with electrical devices
plugged in and turned on.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage
fuel tank causing a fire, resulting in
death or serious injury.
Contact with muffler area could cause burns
resulting in serious injury.
• DO NOT touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 1.5 m (5 ft.) of clearance on all sides of
generator including overhead.
• Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
• Replacement parts must be the same and installed in the
same position as the original parts.

Not for
Reproduction
14 BRIGGSandSTRATTON.com.au
Connecting Electrical Loads
1. Make sure the green output indicator light comes
on (it may take up to three seconds).
2. Let engine stabilize and warm up for a few
minutes after starting.
3. Plug in and turn on the desired 230 Volt AC,

NOTICE
• DO NOT connect 115 Volt loads to the 230 Volt
receptacles.
• DO NOT connect 3-phase loads to the generator.
  
  
Generator Capacity.
NOTICE Exceeding generators wattage/amperage
capacity could damage generator and/or electrical
devices connected to it.
• DO NOT exceed the generator’s wattage/amperage
capacity. See Generator Capacity.
• Start generator and let engine stabilize before connecting
electrical loads.
• Connect electrical loads in OFF position, then turn ON for
operation.
• Turn electrical loads OFF and disconnect from generator
before stopping generator.
Parallel Operation
Two Briggs & Stratton inverter generators can be run
in parallel with a Briggs & Stratton parallel operation kit
(optional equipment) for a total output of power of up to
4,800 watts (4.8 kW).
Models Maximum Output
P2200 & P2200 3000 Watts
P2200 & P3000 3000 Watts
P3000 & P3000 4800 Watts
NOTICE Total electrical load connected to the
parallel kit must not exceed 4,800 watts (4.8 kW).
See the parallel operation kits instruction sheet for
detailed instructions on installation and operation of the
connected generators.
NOTICE
• Turn electrical loads OFF and disconnect from
both generators.
• The QPT switch must be in the same position on
both generators.
• Connect the power cables to both generators
before starting the engines. See instruction sheet
supplied with parallel kit.
• Start engine on one of the inverter generators
according to Starting the Engine.
• Once the green LED output indicator light on the
first generators is steady, start second generator.
• Connect and turn on electrical loads to the parallel
panel receptacles.
• DO NOT disconnect power cables after engines
have been started.
• Shut down engines as described in Stopping the
Engine.
Stopping the Engine
1. Turn OFF and unplug all electrical loads from
generator panel receptacles. NEVER start or stop
engine with electrical devices plugged in and
turned ON.
2. Let engine run at no-load for several minutes
to stabilize internal temperatures of engine and
generator.
3. Turn engine switch to the OFF (0) position.

This feature is designed to greatly improve fuel
economy. When this switch is turned ON, the
engine speed will increase as electrical loads are
connected, and decreased as electrical loads are
removed.
With the switch off, the engine will run at a higher
speed.
NOTICE Always have the switch OFF when using the
DC receptacle.
WARNING Fuel and its vapors are extremely
flammable and explosive which could
cause burns, fire or explosion
resulting in death or serious injury.
• DO NOT stop engine by moving choke lever to
( ) position.

Not for
Reproduction
15
Charging a Battery
Your generator has the capability of recharging a
discharged 12 Volt automotive or utility style storage
battery.
NOTICE
• Not for use with any other type of battery.
• DO NOT use the unit to charge any 6 Volt
batteries.
• DO NOT use the unit to crank an engine having a
discharged battery.
To recharge 12 Volt batteries, proceed as follows:
1. Make sure QPT switch is in OFF (0) position.
2. If necessary, clean battery posts or terminals.
3. Check fluid level in all battery cells. If necessary,
add ONLY distilled water to cover separators in
battery cells. DO NOT use tap water.
4. If the battery is equipped with vent caps, make
sure they are installed and are tight.
5. Connect battery charge cable clamp with red
handle to battery post or terminal indicated by
Positive,POS or (+).
6. Connect battery charge cable clamp with black
handle to battery post or terminal indicated by
Negative, NEG, or (–).
7. Connect battery charge cable connector plug to
the 12 Volt DC panel receptacle.
8. Start generator as described in Starting The
Engine. Let the engine run while battery
recharges.
NOTICE Normally a period of 30 to 120 minutes is
sufficient to recharge a weak battery.
9. When battery has charged, shut down engine as
described in Stopping The Engine.
10. Remove the battery charging cable from the
generator and then disconnect from the battery
posts.
NOTICE Use an automotive hydrometer to test battery
state of charge and condition. Follow the hydrometer
manufacturer’s instructions carefully. Generally, a battery
is considered to be at 100% state of charge when
specific gravity of its fluid (as measured by hydrometer)
is 1.260 or higher.
WARNING Storage batteries give off explosive
hydrogen gas during recharging.

a long time after battery has been
charged. Slightest spark could ignite hydrogen
causing explosion resulting in death or serious
injury.
Battery electrolyte fluid contains acid and is
extremely caustic. Contact with battery fluid could
cause chemical burns resulting in serious injury.
• DO NOT allow any open flame, spark, heat, or lit
cigarette during and for several minutes after charging a
battery.
• Wear protective goggles, rubber apron, and rubber
gloves.
• DO NOT continue to charge a battery that becomes hot
or is fully charged.
• DO NOT leave battery unattended.

Not for
Reproduction
16 BRIGGSandSTRATTON.com.au
Generator Capacity
To make sure your generator can supply enough
running watts and starting watts for the items you will
power at the same time, follow these simple steps:
1. Select the items you will power at the same time.
See following list for typical wattages.
* Typical wattages listed are approximate only. Check
tool or appliance for actual wattage.
** Per Briggs & Stratton 628K, Starting Watts represents
the momentary electrical current the generator can
provide to start electric motors. Starting Watts does
not represent the power required to continuously run
electrical loads. Starting Watts is the maximum current
that can momentarily be supplied when starting a
motor, multiplied by the generator’s rated voltage.
2. Total the running watts. This is the amount of
power your generator must produce to keep your
items running. See following example:
Example:
Total Running Watts = 2355
 
Total Generator Watts Required = 4355
3. Estimate the Starting Watts you will need. Because
not all motors start at the same time, total Starting
Watts can be estimated by adding only the
item with the highest additional Starting Watts
requirements to the total running watts from step 2.
Power Management
To manage generator power, sequentially add loads as
follows:
1. With nothing connected to generator, start the
engine outdoors.
2. Plug in and turn on the first load, preferably the
largest load you have.
3. Permit the generator output to stabilize (engine runs
smoothly and attached device operates properly).
4. Plug in and turn on the next load.
5. Again, permit the generator to stabilize.
6. Repeat steps 4 and 5 for each additional load.
NEVER add more loads than the generator capacity.
Take special care to consider surge loads in generator
capacity.
Maintenance
Maintenance Schedule
Follow the hourly or calendar intervals, whichever
occurs first. More frequent service is required when
operating in adverse conditions noted below.
1Service more often under dirty or dusty conditions.
General Recommendations
Regular maintenance will improve the performance
and extend the life of the generator. See any
authorized dealer for service.
The generator’s warranty does not cover items that have
been subjected to operator abuse or negligence. To
receive full value from the warranty, the operator must
maintain the generator as instructed in this manual.
NOTICE Improper treatment of generator could
damage it and shorten its life.
• NEVER operate generator without protective housing or
covers to assure proper cooling.
Some adjustments will need to be made periodically to
properly maintain your generator.
All service and adjustments should be made at least
once each season. A new spark plug and clean
air filter assure proper fuel-air mixture and help
your engine run better and last longer. Follow the
requirements in the Maintenance Schedule.
Every 8 Hours or Daily
• Clean debris
• Check engine oil level
First 10 Hours
• Change engine oil
Every 50 Hours
• Service engine air cleaner and breather filter1
• Change engine oil1
Every 100 Hours
• Clean fuel strainer
• Service spark plug
• Inspect muffler and spark arrester
Every 250 Hours or Yearly
• Check valve clearance
Tool or Appliance Running
Watts*
Starting
Watts**
Light Bulb - 75 Watt 75 -
Pump 800 1200
Refrigerator/Freezer 800 2000
 1000 2000
Air Conditioner- 13,500 BTU 1200 1800
 800 1300
Microwave Oven - 1000 Watt 1000 -
Color Television - 42” 280 -
Personal Computer w/17” monitor 800 -

Not for
Reproduction
17
Generator Maintenance
Generator maintenance consists of keeping the unit
clean and dry. Operate and store the unit in a clean dry
environment where it will not be exposed to excessive
dust, dirt, moisture, or any corrosive vapors. Cooling
air slots in the generator must not become clogged
with snow, leaves, or any other foreign material.
NOTICE DO NOT use water or other liquids to clean
generator. Liquids can enter engine fuel system,
causing poor performance and/or failure to occur. In
addition, if liquid enters generator through cooling air
slots, some of the liquid will be retained in voids and
cracks of the rotor and stator winding insulation. Liquid
and dirt buildup on the generator internal windings will
eventually decrease the insulation resistance of these
windings.
Cleaning
Daily or before use, look around and underneath
the generator for signs of oil or fuel leaks. Clean
accumulated debris from inside and outside the
generator. Keep the linkage, spring and other engine
controls clean. Keep the area around and behind
the muffler free from any combustible debris. Inspect
cooling air slots and openings on generator. These
openings must be kept clean and unobstructed.
Engine parts should be kept clean to reduce the risk of
overheating and ignition of accumulated debris:
• Use a damp cloth to wipe exterior surfaces clean.
NOTICE Improper treatment of generator could
damage it and shorten its life.
• DO NOT expose generator to excessive moisture, dust,
dirt, or corrosive vapors.
• DO NOT insert any objects through cooling slots.
• Use a soft bristle brush to loosen caked on dirt or
oil.
• Use a vacuum cleaner to pick up loose dirt and
debris.
Cleaning Fuel Strainer
The fuel strainer helps prevent debris from entering the
fuel system.
Clean the fuel strainer as follows:
1. Make sure generator is on a level surface.
2. Remove the fuel cap (A) and fuel strainer (B).
3. Wash fuel strainer in liquid detergent and water.
4. Wipe fuel strainer clean with a clean, dry cloth.
5. Carefully reinstall the fuel strainer and fuel cap.
Engine Maintenance
Oil
Oil Recommendations
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF,

Outdoor temperatures determine the proper oil viscosity
for the engine. Use the chart to select the best viscosity
for the outdoor temperature range expected.
* Below 40°F (4°C) the use of SAE 30 will result in hard starting.
** Above 80°F (27°C) the use of 10W30 may cause
increased oil consumption. Check oil level more frequently.
B
A
WARNING Unintentional sparking could cause
fire or electric shock resulting in
death or serious injury.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR
GENERATOR
• Disconnect the spark plug wire from the spark plug and
place the wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
• Use approved spark plug tester.
• DO NOT check for spark with spark plug removed.

Not for
Reproduction
18 BRIGGSandSTRATTON.com.au
Checking Oil Level
Oil level should be checked prior to each use or
at least every 8 hours of operation. Keep oil level
maintained.
1. Make sure generator is on a level surface.
2. Loosen the side maintenance cover screws and
remove the side maintenance cover.
3. Clean area around oil fill and remove oil fill cap.
4. Verify oil is at the point of overflowing at oil fill
opening.
5. Replace and tighten oil fill cap.
6. Reinstall the side maintenance cover and hand
tighten the cover screws.
Adding Engine Oil
1. Make sure generator is on a level surface.
2. Repeat steps 2 through 4 to check oil level as
described in Checking Oil Level.
3. If needed, slowly pour oil into oil fill opening to the
point of overflowing at oil fill.
4. Replace and tighten oil fill cap.
5. Reinstall the side maintenance cover and hand
tighten the cover screws.
Changing Engine Oil
If you are using your generator under extremely dirty or
dusty conditions, or in extremely hot weather, change
the oil more often.

DON’T POLLUTE. CONSERVE
RESOURCES. RETURN USED OIL TO
COLLECTION CENTERS.
Change the oil while the engine is still warm from
running, as follows:
1. Make sure generator is on a level surface.
2. Loosen the side maintenance cover screws and
remove the side maintenance cover.
3. Clean area around oil fill and remove oil fill cap.
4. Tip your generator to drain oil from oil fill into a
suitable container making sure you tip your unit
toward the oil filler neck. When crankcase is
empty, return generator to upright position.
5. Slowly pour oil (about 20 oz.) into oil fill opening
to the point of overflowing at oil fill cap. DO NOT
overfill.
6. Reinstall oil fill cap. Finger tighten cap securely.
7. Wipe up any spilled oil.
8. Reinstall the side maintenance cover and hand
tighten the cover screws.
CAUTION Avoid prolonged or repeated skin
contact with used motor oil.
• Used motor oil has been shown to cause skin cancer in
certain laboratory animals.
• Thoroughly wash exposed areas with soap and water.

Not for
Reproduction
19
Service Air Cleaner
Your engine will not run properly and may be damaged
if you run it with a dirty air cleaner. Service more often
if operating under dirty or dusty conditions.
To service the air cleaner, follow these steps:
1. Loosen the side maintenance cover screws and
remove the side maintenance cover.
2. Loosen air cleaner cover screw (A) and remove
air cleaner cover (B).
3. Carefully remove foam air cleaner (C) by pulling it
out towards you.
4. Carefully remove pre-filter (D) by pulling it out
towards you.
5. Wash foam air cleaner and breather filter in liquid
detergent and water only. Squeeze dry in a clean cloth.
6. SATURATE foam air cleaner in clean engine oil
and squeeze in a clean cloth to remove excess oil.
7. Reinstall clean or new foam air cleaner inside base.
8. Reinstall clean or new breather filter inside base.
9. Reinstall the air cleaner cover and tighten screw.
10. Reinstall the side maintenance cover and hand
tighten the cover screws.
Service Spark Plug
Changing the spark plug will help your engine to start
easier and run better.
1. Push in on tab with srewdriver and remove top
maintenance cover.
2. Clean area around spark plug and remove spark
plug boot.
3. Remove spark plug and inspect spark plug.
4. Replace spark plug if electrodes are pitted,
burned or porcelain is cracked. Use the
recommended replacement plug. See
Specifications.
5. Check electrode gap with wire feeler gauge and
reset spark plug gap to recommended gap if
necessary (see Specifications).
6. Install spark plug and tighten firmly. Reinstall
spark plug boot.
7. Reinstall top maintenance cover.
Inspect Muffler and Spark Arrester
Inspect the muffler for cracks, corrosion, or other
damage. Remove the spark arrester, if equipped, and
inspect for damage or carbon blockage. If replacement
parts are required, make sure to use only original
equipment replacement parts.
C
B
D
A

Not for
Reproduction
20 BRIGGSandSTRATTON.com.au
Clean and inspect the spark arrester as follows:
1. Remove two screws that attaches back bumper to
muffler guard. Remove back bumper.
2. To remove muffler guard, remove two top screws
that connects guard to generator.
3. Remove screw that attaches spark arrester screen
to muffler. Remove spark arrester screen.
4. Inspect screen and obtain a replacement if torn,
perforated or otherwise damaged. DO NOT use a
defective screen. If screen is not damaged, clean
it with a brush.
5. Reattach screen to muffler. Reattach muffler guard.
Storage
The generator should be started at least once every
seven days and allowed to run at least 30 minutes. If
this cannot be done and you must store the unit for
more than 30 days, use the following guidelines to
prepare it for storage.
Generator Storage
• Clean the generator as outlined in Cleaning.
• Check that cooling air slots and openings on
generator are open and unobstructed.
Long Term Storage Instructions
Fuel can become stale when stored over 30 days.
Stale fuel causes acid and gum deposits to form in the
fuel system or on essential carburetor parts. To keep
fuel fresh, use Briggs & Stratton® Advanced Formula
Fuel Treatment & Stabilizer, available wherever Briggs
& Stratton genuine service parts are sold.
There is no need to drain gasoline from the engine
if a fuel stabilizer is added according to instructions.
Run the engine for 2 minutes to circulate the stabilizer
throughout the fuel system before storage.
If gasoline in the engine has not been treated with a
fuel stabilizer, it must be drained into an approved
container. Run the engine until it stops from lack
of fuel. The use of a fuel stabilizer in the storage
container is recommended to maintain freshness.
WARNING Exhaust heat/ gases could ignite
combustibles, structures or damage
fuel tank causing a fire, resulting in
death or serious injury.
Contact with muffler area could cause burns
resulting in serious injury.
• DO NOT touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 1.5 m (5 ft) of clearance on all sides of
generator including overhead.
• Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
• Replacement parts must be the same and installed in the
same position as the original parts.
WARNING Fuel and its vapors are extremely
flammable and explosive which could
cause burns, fire or explosion
resulting in death or serious injury.
WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN
TANK
• Store away from furnaces, stoves, water heaters, clothes
dryers or other appliances that have pilot light or other
ignition source because they could ignite fuel vapors.
WHEN DRAINING FUEL
• Turn generator engine OFF and let it cool at least 2
minutes before removing fuel cap. Loosen cap slowly to
relieve pressure in tank.
• Drain fuel tank outdoors.
• Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
• Check fuel lines, tank, cap and fittings frequently for
cracks or leaks. Replace if necessary.
• DO NOT light a cigarette or smoke.