BRIGHTLIGHT BL-DMX-104 User manual
DIMENSIONSDETAIL DIAGRAM
123 4567 8 91 0
ON DIP
RUN TX/RX
RUNNING LIGHT
Turns on when connected
to power supply
DIP SWITCH
TX/RX LED
Indicator light ashes in
data transmission SENDER / RECEIVER UINIT
BL-DMX-104
SIGNAL INPUT/
OUTPUT SOCKET
DC5V~24V
Power Input Socket
INSTALLATION GUIDE
Actual product characteristics may vary. Bright Light reserves the right to improve, modify or update the product designs without prior notice.
4-CHANNEL DMX TRANSCEIVER
CODE
BL-DMX-104
INPUT/ OUTPUT DMX 512 signal
VOLTS 5–24V DC
DIMENSIONS W44 × L175 × H30mm
HOUSING PVC casing
MOUNTING 2 × mounting tabs
WARRANTY 5 years
COMPLIANCE
OPERATING TEMP. -30°C ~ +55°C
INGRESS
PROTECTION
Indoor use only
CONNECTION
METHOD
Concealed screw terminals
CONTROL DMX 512 signal
MAX. DISTANCE
FROM POWER
SUPPLY
Recommended under 10 metres
For specic projects contact Bright
Light
FUNCTION
– Frequency of 2.4GHz ISM 64 channels
– DMX control for single colour, Tuneable white, RGB, and RGBW LED ribbon strip or other constant voltage luminaires
– Send DMX signal from a single unit and have multiple units receiving with instant, seamless results.
– Ideal for retro t applications where cable installation is a challenge
175mm
44mm
170mm
30mm
DIP SWITCH OPERATION
The 10th Dip Switch:
When set to OFF unit will be congured as sender.
When set to ON unit will be congured as receiver.
The 9th Dip Switch The 7-8 Dip Switch:
4 levels of transmission power
The 1-6 Dip Switch
64 frequencies to select (2401~2464MHz), the interval of
frequency is 1Mhz
DIP 1 2 3 4 5 6
VALUE 001 002 004 008 016 032
Frequency value = the total place value amount of 1-6 dip switch + 2400,
put the dip switch to ON position, user can get its place value, put dip
switch to OFF position, its place value is 0.
dBm 7 8
20 OFF OFF
10 OFF ON
5 ON OFF
1 ON ON
Figure 2 shows the normal mode when OFF, sending out the data
from the DMX console.
Figure 3 shows the self-testing mode when on, sending out the auto-
generated DMX console data (full colour smooth changing effect)
Example: Figure 5 - the repeater frequency is 2437m
Set the 1st, 3rd and 6th dip dwitch to “1”, the rest to “0”.
The value summation from 1-6 is 1+4+32 = 37,
So the repeater frequency is 37+2400 = 2437m
Valid when it is
congured as
sending end.
0800 952 000 | www.brightlight.co.nz | BRIGHTLIGHT
ATTENTION:
– The product shall be installed and serviced by a professional electrician.
– This product is not waterproof & cannot be installed outdoors, use IP65 box if required for outside use.
– Good heat dissipation on will prolong the working life of the repeater, please ensure good ventilation.
– Please check the output voltage of any power supply used complies with the working voltage of the LED
product used.
– Ensure an adequate sized cable is used from the controller to the LED lights to carry the current, please also
ensure the cable is secured tightly in the connector.
– Ensure all wire connections and polarities are correct before applying power to avoid any damages to the
LED lights.
– If a fault occurs please return product to your supplier. Do not attempt to x this product yourself.
WIRELESS DIAGRAM RELAY WAY TO EXTEND THE COMMUNICATION DISTANCE
TRANSMITTING
TERMINAL
RECEIVING
TERMINAL
RELAY STATION
INSTALLATION GUIDE
Actual product characteristics may vary. Bright Light reserves the right to improve, modify or update the product designs without prior notice. 0800 952 000 | www.brightlight.co.nz | BRIGHTLIGHT
