Brinkmann 810-3331-F User manual

OWNER’S MANUAL / NOTICE D’UTILISATION
ASSEMBLY AND OPERATING INSTRUCTIONS
INSTRUCTIONS D’ASSEMBLAGE ET D’UTILISATION
WARNING/AVERTISSEMENT
HAZARDOUS EXPLOSION MAY RESULT IF THESE WARNINGS
AND INSTRUCTIONS ARE IGNORED. READ AND FOLLOW ALL
WARNINGS AND INSTRUCTIONS IN THIS MANUAL TO AVOID
PERSONAL INJURY, INCLUDING DEATH OR PROPERTY DAMAGE.
UNE EXPLOSION DANGEREUSE RISQUE DE SE PRODUIRE SI CES
AVERTISSEMENTS ET INSTRUCTIONS SONT IGNORÉS. LIRE ET
RESPECTER TOUS LES AVERTISSEMENTS ET INSTRUCTIONS DE
CETTE NOTICE POUR ÉVITER DES BLESSURES GRAVES, VOIRE
MORTELLES, OU DES DÉGÂTS MATÉRIELS.
NOTICE TO INSTALLER:
LEAVE THESE INSTRUCTIONS WITH
THE GRILL OWNER FOR FUTURE
REFERENCE.
AVIS À L’INSTALLATEUR:
REMETTRE CETTE NOTICE AU
PROPRIÉTAIRE POUR QU’IL PUISSE S’Y
RÉFÉRER PLUS TARD.
3 Burner Gas Grill
Grill au gaz 3 brûleurs
SAVE THIS MANUAL FOR FUTURE REFERENCE
CONSERVER CETTE NOTICE POUR RÉFÉRENCE
Model/Modèle 810-3331-F

1
WE WANT YOU TO ASSEMBLE AND USE YOUR GRILL AS SAFELY AS POSSIBLE.
THE PURPOSE OF THIS SAFETY ALERT SYMBOL IS TO ATTRACT YOUR ATTENTION TO
POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR GRILL.
WHEN YOU SEE THE SAFETY ALERT SYMBOL
PAY CLOSE ATTENTION TO THE INFORMATION WHICH FOLLOWS!
READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY
BEFORE ASSEMBLING AND OPERATING YOUR GRILL.
IF YOU SMELL GAS:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, keep away from the appliance and immediately call your gas supplier or your
fire department.
DANGER
IMPORTANT SAFETY
WARNINGS
a) Do not store a spare LP cylinder under or near this appliance.
b) Never fill the cylinder beyond 80% full.
c) If the information in (a) and (b) is not followed exactly, a fire causing death or
serious injury may occur.
DANGER
1. Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any
other appliance.
2. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other
appliance.
WARNING

TABLE OF CONTENTS:
General Warnings................................................3-4
LP Gas Cylinder (Tank) Specifications and Installation ...................4-6
Hose & Regulator Specifications and Installation .......................6-7
Leak Testing....................................................7-8
Pre-start Check List ...............................................9
Lighting Instructions.............................................9-10
Operating the Grill .............................................11-12
Using Other Features of the Grill .................................... 12
Proper Care and Maintenance....................................13-15
Transporting and Storage .........................................15
Trouble Shooting ..............................................16-17
Grill Cooking Tips................................................17
Assembly Instructions ..........................................18-30
Warranty Information ......................................Back Cover
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING: Be alert to the possibility of serious bodily injury if the instructions are not followed. Be sure
to read and carefully follow all of the messages.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury.
FOR COVERS, ACCESSORIES AND OTHER PRODUCTS, PLEASE VISIT US ONLINE AT:
2

LP GAS CYLINDER (TANK) SPECIFICATIONS AND INSTALLATION:
3
• Leaktestallconnectionsbeforefirstuse,even if grill was purchased fully assembled and after
each tank refill. Check the propane tank rubber seal for damage.
• Alwayscheckthegrillandpropanetankpriortoeachuseasindicatedinthe“Checkingfor
Leaks”&“Pre-StartCheckList”sectionsofthismanual.
• Neverusenaturalgasinaunitdesignedforliquidpropanegas.
• Neverusecharcoal,lavarocksorwoodbriquetsinagasgrill.Flavoringchipsmustbe
contained in a metal smoking box to contain ash and prevent fires.
• Ensureflamescomeoutofallburnerportsateachuse.Spidersandinsectsliketobuildnests
in burner tubes. Blocked burner tubes can prevent gas flow to the burners and could result in a
burner tube fire or fire beneath the grill.
• Nevercheckforleaksusingamatchoropenflame.
• Neveruseorstoregasoline,lighterfluid,paintthinner,orotherflammablevaporsandliquidsor
combustible materials in or near your grill.
• DONOTblockventilationareasinsides,backorcartcompartmentofgrill.
• DONOTcovercookinggratesorothercomponentswithaluminumfoil,asthisblocks
ventilation and damage to grill or personal injury may occur.
• Neverplacemorethan15poundsonthesidetables.DONOTleanonthesidetables.DONOT
lift grill using side tables.
• Keepchildrenandpetsawayfromhotgrill.DONOTallowchildrentouseorplaynearthisgrill.
• DONOTleavethegrillunattendedwhileONorinuse.
• DONOTallowthegashosetocomeincontactwithhotsurfaces.Redirectthegashoseif
necessary.
• DONOTallowgreaseorhotdrippingstofallonhoseandregulatorassembly.Ifthisoccurs,
turn gas supply OFF at once. Empty grease tray/cup and clean the hose and regulator assembly
and inspect for damage before use.
• Nevercookonthegrillwithoutthegreasecup/trayinposition.
• Keepanyelectricalsupplycordsawayfromwaterorheatedsurfaces.
• DONOTusewateronagreasefire.Closingthelidtoextinguishagreasefireisnotpossible.
Use type BC dry chemical fire extinguisher or smother with dirt, sand or baking soda.
• DONOTusewhileundertheinfluenceofdrugsoralcohol.
• FOROUTDOORUSEONLY.DONOToperateindoorsorinanenclosedareasuchasagarage,
shed or breezeway.
• Positionyourgrilloutdoorsonanon-combustiblelevelsurfaceinawellventilatedlocation,a
safe distance 10 ft. (3.1 m) from combustible materials, buildings and overhangs.
• Apartmentdwellers:Checkwithmanagementandfollowtherequirementsandfirecodesfor
using an LP gas grill in your apartment complex. Only use outside on the ground (not on a
balcony,patio,garage,etc)witha15foot(4.6m)minimumclearanceonallsidesfromanywall,
structure or combustible material.
• Maintainaminimumclearanceof36inches(91cm)betweenallsidesofgrill,deckrailings,
walls or other combustible material. Not adhering to these clearances may prevent proper
ventilation and can increase the risk of a fire and/or property damage, which could also result in
personal injury. DO NOT use grill under overhead unprotected combustible construction.
• DONOTuseorinstallthisgrillinoronarecreationalvehicleand/orboat.
• DONOTbuildthismodelgrillinanybuilt-inorslideinconstruction.
• Ifabristlebrushisusedtocleananyofthecookingsurfaces,ensurenoloosebristlesremain
on the cooking surfaces prior to grilling as loose bristles may attach to food.
• DONOTstoreitemsincartthatcancatchfireordamageyourgrill(suchasswimmingpool
supplies/chemicals, table cloth, wood chips).
WARNING
GENERAL WARNINGS:

LP GAS CYLINDER (TANK) SPECIFICATIONS AND INSTALLATION:
4
• DONOTstoreaspareLPgascylinder(fullorempty)underornearyourgrill.Thiscouldcause
excess pressure to be expelled through the vapor relief valve resulting in fire, explosion, or
severe personal injury, including death.
• Propanegasisheavierthanairandwillcollectinlowareas.Properventilationisextremely
important.Keeptheventilationopening(s)oftheLPgascylinderenclosurefreeandclearfrom
obstructions and debris.
• DONOTinsertanyforeignobjectsintothecylindervalveoutletasthiscoulddamagethe
rubber seal. Do not use propane tank with a damaged rubber seal. A damaged rubber seal can
cause a gas leak, possibly resulting in explosion, fire, severe bodily harm, or death. Inspect
rubber seal for cracks, wear or deterioration prior to use.
• Alwayskeepcylinder(tank)inuprightpositionduringuse,transitorstorage.
• ONLYconnectthisgrilltoaType1cylindervalve.TheType1valvecanbeidentifiedwiththe
large external threads on the valve outlet.
• DONOTconnecttoapropanecylinderexceedinga20lb.(9.1kg)capacity.
• DONOTconnecttoacylinderthatusesanyothertypeofvalveconnectiondevice.
• Inspectthepropanetankvalverubbersealforcracks,wearordeteriorationpriortouse.A
damaged rubber seal can cause a gas leak, possibly resulting in an explosion, fire or severe
bodily harm.
• Turnoffthecylindervalvewhenyourgrillisnotinuse.
• Handlethetankwithcare.
• Alwayssecurethecylinderinanuprightposition.
• NeverconnectanunregulatedLPgascylindertoyourgrill.
• DONOTexposeLPgascylinderstoexcessiveheatorignitionsources.
• DONOTstoreaspareLPgascylinderunderornearyourgrill.
• AllowonlyqualifiedLPgasdealerstofillorrepairyourLPgascylinder.
• DONOTallowthecylindertobefilledbeyond80%capacity.
• Readandfollowallwarningsandinstructionsthatareonthecylinderandthataccompanythis
product.
• Grillishotwheninuse.Toavoidburns:
 • DONOTattempttomovethegrill.
 • Blockthewheelssotheunitdoesnotaccidentallymove.
 • Wearprotectiveglovesorovenmitts.
 • DONOTtouchanyhotgrillsurfaces.
 • DONOTwearlooseclothingorallowhairtocomeincontactwithgrill.
• Notforcommercialuse.DONOTusethisgrillforanythingotherthanitsintendedpurpose.
USE CAUTION AND COMMON SENSE WHEN OPERATING YOUR GAS GRILL.
FAILURE TO ADHERE TO THE SAFETY WARNINGS AND GUIDELINES IN THIS
MANUAL COULD RESULT IN SEVERE BODILY INJURY OR PROPERTY DAMAGE.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
WARNING
DANGER

5
LPGASCYLINDER(TANK)SPECIFICATIONS:
LP gas cylinder (not supplied with this grill)
The LP (Liquid Propane) gas cylinder specifically designed to be used with this grill must be 12” (30.5
cm) diameter x 18” (45.7 cm) tall and have a 20 lb. (9.1 kg) capacity incorporating a Type 1 cylinder valve
and an over-filling protection device (OPD).
This grill is designed to fit Worthington, Manchester or SMPC brand 20 lb. (9.1 kg) cylinders. Other brand
DOT cylinders may fit this grill if the cylinder has similar dimensions of the top and bottom rings.
The installation of this appliance must be in accordance with:
All applicable local codes, or in the absence of local codes, either:
• NationalFuelGasCodeANSIZ223.1NFPA54
• NaturalGasandPropaneInstallationCode:CAN/CGAB149.1
• NaturalGasInstallationCode:CAN/CGAB149.1(Canada)
• PropaneInstallationCode:CAN/CGAB149.2(Canada)
To check your local codes, see your local LP gas dealer or natural gas company. This grill was not
intended to be connected to a natural gas supply line. If an external electrical source is utilized, it must be
electrically grounded in accordance with local codes, or in the absence of local codes, with the National
ElectricalCode,ANSI/NFPA70,ortheCanadianElectricalCode,CSA22.1.
When purchasing or exchanging a cylinder for your gas grill, it must be constructed and marked in
accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT)
ortheNationalStandardofCanada,CAN/CSA-B339Cylinders,SpheresandTubesforTransportation
of Dangerous Goods; and Commission, as applicable; and provided with a listed over-filling prevention
device (OPD), and provided with a cylinder connection device compatible with the connection for outdoor
cooking appliances.
The cylinder must also be equipped with:
 • Ashut-offvalveterminatinginaType1gascylindervalveoutlet.
 • AType1valvethatpreventsgasflowuntilapositivesealisobtained.
 • Anarrangementforvaporwithdrawal.
 • Acollartoprotectthecylindershut-offvalve.
 • Asafetyreliefdevicehavingdirectcommunicationwiththevaporspaceofthecylinder.
 • Alistedover-fillingpreventiondevice(OPD).
FILLINGTHELPGASCYLINDER(TANK):
• AllowonlyqualifiedlicensedLPgasdealerstoproperlyfillorrepairyourLPgascylinder.
• Newtanksshouldbepurgedpriortofilling;informLPgasdealerifyouareusinganewtank.
• DONOTallowthecylindertobefilledbeyond80%capacity.Over-filledtankscancreatea
dangerouscondition.Over-filledtankscanbuild-uppressureandcausethereliefvalvetoexpel
propane gas vapors. The vapor is combustible and if it comes in contact with a spark source or
flame an explosion causing severe burns, bodily harm, or death could occur.
• Alwaysuseaprotectivecylindercapwhengrillisnotconnectedtocylinder.
• Ifyouexchangeacylinderwithaqualifiedexchangeprogram,thenewcylindermusthave
aType1valveandanover-fillingpreventiondevice(OPD).
• Inspectthepropanetankvalverubbersealforcracks,wearordeteriorationpriortouse.A
damaged rubber seal can cause a gas leak, possibly resulting in an explosion, fire or severe
bodily harm.
WARNING

Tank
Support
Bracket
Tank
Brace
LPGASCYLINDER(TANK)RUBBERSEALINSPECTION:
• Inspectthepropanetankvalverubbersealforcracks,wear
or deterioration prior to use. A damaged rubber seal can
cause a gas leak, possibly resulting in an explosion, fire or
severe bodily harm.
• Inspectionshouldbedoneeachtimethepropanetankis
connected to the grill, has been refilled, exchanged or has
not been used for more than 60 days.
• Donotuseapropanetankwithadamagedrubberseal.
Exchange the tank or have the rubber seal replaced at a
qualified propane filling station.
INSTALLINGTHELPGASCYLINDER(TANK)ONTOTHEGRILL:
1. Check that the cylinder valve is closed by turning the knob clockwise. Inspect cylinder valve rubber seal for
cracks or deterioration. Do not use propane tank with damaged seal as a gas leak may occur.
2. Place the cylinder into the tank holder in the bottom of cabinet.
3. Orient the cylinder such that the valve opening faces the right side of the grill, and the hose is not kinked or
damaged.
4. Fully tighten the tank retention screw underneath tank holder to secure tank.
6
Good
Rubber Seal
Damaged
Rubber Seal
HOSE & REGULATOR SPECIFICATION AND INSTALLATION:
• Fordualfuelgrillsthatcanbeconvertedtonaturalgas,aBrinkmannconversionkitmustbe
purchased and installed for use with natural gas. Please contact Brinkmann Customer Service
at800-527-0717toseeifyourgrillcanbeconverted.
• DONOTuseanyotherpressureregulator/hoseassemblyotherthantheonesuppliedwithyour
grill.Replacementpressureregulator/hoseassemblymustbepartNo155-3331-0,whichcanbe
obtainedbycontactingcustomerserviceat800-527-0717.
• DONOTattempttoadjustorrepairaregulator.Theregulatorisdesignedtooperateata
maximumoutputpressureof11inchesofwatercolumn(2.74kPa).
• EnsurethetankvalveisCLOSED prior to connecting the LP gas cylinder to your grill. Turn the
valve knob clockwise to properly close the valve. Read and follow all instructions and warnings
on the supply hose safety tags. Read and follow all warnings in this manual concerning the safe
use of LP gas cylinders and the hose and regulator before connecting cylinder to grill. Read and
follow all warnings on the LP cylinder.
WARNING

HOSE AND REGULATOR:
Your grill is equipped with a Type 1 connection device with the following features:
1. The system will not allow gas flow from the cylinder until a positive connection to the valve has been
made.
Note: The cylinder valve and all grill burner knobs must be turned OFF before any connection is
made or removed.
2. A regulator flow limiting device, when activated, restricts the flow of gas to 10 cubic feet per hour. If
the flow limiting device is activated, perform Regulator Resetting Procedure.
Note: If your grill will not get hot enough to cook, the flow limiting device may have been activated.
CONNECTING HOSE AND REGULATOR:
1. Inspect the propane tank valve rubber seal for cracks, wear or
deterioration prior to use. A damaged rubber seal can cause a gas
leak, possibly resulting in an explosion, fire or severe bodily harm.
Do not use a propane tank with a damaged rubber seal.
2. Attach or detach regulator to the LP gas cylinder only when
cylinder is at rest in tank holder.
3. Check that the cylinder valve is closed by turning the knob
clockwise.
4. Check that the grill’s burner control knobs are in the “OFF”
positions.
5. Visually inspect the hose assembly prior to each use for evidence of damage, excess wear, or
deterioration. If found, replace the assembly before using your grill. Only the manufacturer’s supplied
replacement should be used.
6. Remove the protective plastic cap from the cylinder valve.
7. Check that the hose does not contain kinks, does not contact sharp edges, and does not contact
surfaces that may become hot during use.
8. Hold regulator and insert the brass nipple into the LP cylinder valve outlet. Ensure that the device is
centered properly.
9. Turn the large coupling nut clockwise by hand and tighten to a full stop. Take care not to cross thread
the coupling nut onto the cylinder valve. Do not use tools to tighten connection.
Note: If you are unable to make the connection, repeat Steps 7 and 8.
10. Leak check all fittings before lighting your grill. See section on “Leak Testing” in this manual.
REGULATOR RESETTING PROCEDURE:
If your grill will not get hot enough to cook, the flow limiting device may have been activated.
Mini Reset:
Turn ALL burner control knobs to “OFF”, turn off the cylinder valve. Wait one minute. Slowly turn
cylinder valve ON and relight grill. If burner flame is higher and grill heats up properly – proceed with
cooking.
Full Reset:
Turn ALL burner control knobs to “OFF”, turn off the cylinder valve. Disconnect hose and regulator
from cylinder. Wait two minutes, reattach hose and regulator and perform leak test.
7
LEAK TESTING:
• Neveruseyourgrillwithoutleaktestingallgasconnections,hosesandpropanetank.Follow
thesectionon“LeakTesting”inthismanualforproperprocedures.
Inspect Rubber Seal
(see page 6)
WARNING

WHENTOPERFORMALEAKTEST:
• Afterassemblingyourgrillandbeforelightingforthefirsttime,evenifpurchasedfullyassembled.
• EverytimetheLPgascylinderisrefilled,exchangedorifanyofthegascomponentsaredisconnectedor
replaced.
• Anytimeyourgrillhasbeenmoved.
• Atleastonceperyearorifyourgrillhasnotbeenusedformorethan60days.
CHECKINGFORLEAKS:
CAUTION: Strong odors, colds, sinus congestion, etc. may prevent the detection of propane by
smell. Use caution and common sense when testing for leaks.
Note: The leak test must be performed in an area that has adequate lighting in order to see if
bubbles are developing and not in a windy or noisy area so larger leaks can be detected by
smell or sound.
1. Create a mixture of 50% water and 50% liquid dishwashing soap.
2. Open the lid.
3. Ensure all control knobs are set to the “OFF” position.
4. Turn on the gas at the cylinder valve. Turn the cylinder valve knob counter-
clockwise to full open. If you hear a rushing sound or smell gas, turn the
gas off. Tighten any leaking connections. If leak is detected at connection
nut and tightening does not stop leak, reinspect propane tank rubber seal.
5. Apply the soapy water mixture to the following:
Supply tank (cylinder) weld.
Connection nut to tank valve.
Back side of connection nut to brass nipple.
Brass nipple connection into regulator.
Regulator connections to gas supply hoses.
Hose connection to gas manifold.
The full length of gas supply hose.
Tank valve to cylinder.
6. Check each place listed (A–H) for growing bubbles, which indicates a leak.
Large leaks may not be detected by bubbles but should produce a rushing
sound or gas smell.
7. Turn off gas supply at cylinder valve.
8. Turn on control knobs to release gas pressure in hose.
9. Turn control knobs to “OFF” position.
10. Tighten any leaking connections. If leak is detected at connection nut and tightening does not stop
leak, reinspect propane tank rubber seal. (see page 6)
11. Repeat soapy water test until no leaks are detected.
12. Turn off gas supply at cylinder valve until you are ready to use your grill.
13. Wash off soapy residue with cold water and towel dry.
14. Wait 5 minutes to allow all gas to evacuate the area before lighting grill.
WARNING: DO NOT use the grill if leaks cannot be stopped. Contact a qualified gas appliance repair
service.
8
To prevent fire or explosion hazard:
 • DONOTsmokeorpermitignitionsourcesintheareawhileconductingaleaktest.
 • PerformtestOUTDOORSinawellventilatedareathatisprotectedfromthewind.
 • Neverperformaleaktestwithamatchoropenflame.
 • Neverperformaleaktestwhilethegrillisinuseorwhilegrillisstillhot.
A
B
C
D
E
F
G
H
DANGER
Watch For Bubbles
F
B
C
D
E
G
H
A

9
PRE-START CHECK LIST:
• Ensurethatthegrillisproperlyassembled.
• Inspectthegassupplyhoseforburns,chaffing,kinks,andproperroutingbeforeeachuse.Ifitis
evident there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to the grill
being used. Replace with hose and regulator Model No. 155-3331-0, which can be obtained by
contacting customer service at 800-527-0717.
• Leakcheckallgasconnections,hoseandpropanetank.Seesectionon“LeakTesting”.
• Ensurethatallelectricalsupplycordsareproperlygrounded.Keepanyelectricalsupplycordandthe
fuel supply hose away from any heated surfaces. Hose should be at least 3 inches from hot surfaces.
• Positionyourgrillonanon-combustiblelevelsurfaceinawellventilatedlocation,asafedistance
10 ft. (3.1 m) from combustible materials, buildings and overhangs.
• Properlyplacetheemptygreasecupunderthegreasedrainholeinthebottomofthegrilltocatch
grease during use.
• DONOTblockventilationareasinsides,backorcartcompartmentofgrill.
Property damage, bodily harm, severe burns, and death could result from failure to follow these
safety steps. These steps should be performed after the grill has been assembled and prior to
each use. DO NOT operate this grill until you have read and understand ALL of the warnings and
instructions in this manual.
LIGHTING INSTRUCTIONS:
Read, understand and follow all warnings and instructions contained in this manual. DO NOT skip
any of the warnings and instructions contained in the preceding sections of this manual.
Follow the instructions exactly.
1. OPEN THE GRILL LID before attempting to light a burner so that fumes do not accumulate
inside the grill. An explosion could occur if grill lid is down.
2. Checkthatallburnercontrolknobsandthecylindervalveareturnedtothe“OFF”position.
3. Turnonthefuelsupplybyslowlyrotatingthecylindervalveknobcounter-clockwisetofull
open.
4. DO NOT stand with head, body, or arms over the grill when lighting.
LIGHTING THE MAIN BURNERS:
1. Open lid before lighting burner.
2. Make sure all control knobs are in the “OFF” position.
3. Push and hold down the IGNITION BURNER control knob and turn
SLOWLY (2 to 3 seconds) to “IGNITE”. You should hear the igniter click.
Note: Step 3 may need to be repeated 2-3 times to light grill.
4. If ignition does NOT occur in 5 seconds, turn control knob to “OFF”, wait
5 minutes to allow gas to dissipate and repeat lighting procedure.
5. To light other burners, push and turn control knobs to “HIGH” in sequence from right to left.
6. If burner does not ignite using the igniter, see “Match Lighting the Main Burners” section.
7. To turn off, turn each control knob clockwise until it locks in the “OFF” position. This does not turn off
the gas flow from the cylinder.
Note: If burner does not light or flame is too low, See “Trouble Shooting” section of the owners
manual.
WARNING
DANGER
IGNITION BURNER
l'ALLUMEUR DU BRÛLEUR
Read Instructions Before Lighting:
1. Open lid during lighting.
2. Push and hold down the IGNITION
BURNER control knob and turn SLOWLY
(2 to 3 seconds) to "HIGH". You should
hear the ignitor click.
3. If ignition does not occur in 5 seconds,
turn the burner control "OFF", wait
5 minutes and repeat lighting procedure.
Veuillez Lire les Instructions
Avant l'Allumage:
1. Ouvrez le couvercle pendant l'allumage.
2. Appuyez sur le bouton de commande
de l'ALLUMEUR DU BRÛLEUR et
maintenez-le enfoncé et tournez
LENTEMENT (2 à 3 secondes) pour
« ÉLEVÉ ». On devrait entendre le bruit
de l'allumeur.
3. Si rien n'arrive après 5 secondes,
placez le bouton de commande à la
position « ÉTEINT», attendez 5 minutes
pour permettre au gaz de se dissiper et
répétez la procédure d'allumage.
FOR OUTDOOR
USE ONLY
UTILISER
UNIQUEMENT
A L’EXTÉRIEUR
SIDE BURNER
LE BRÛLEUR DE CÔTÉ
WWW.BRINKMANN.NET
800-527-0717
ForAccessories, Parts or Assistance,
Callor Visit our Website
Appelez-nousou visitez notre site pour obtenir
desaccessoires, des pièces ou de l'aide
O
F
F
É
T
E
I
N
T
L
O
W
F
A
E
I
BL
H
I
G
H
É
L
E
V
É
O
F
F
É
T
E
I
N
T
L
O
W
F
A
E
I
BL
H
I
G
H
É
L
E
V
É
O
F
F
É
T
E
I
N
T
L
O
W
F
A
E
I
BL
H
I
G
H
É
L
E
V
É
O
F
F
É
T
E
I
N
T
L
O
W
F
A
E
I
BL
H
I
G
H
É
L
E
V
É
MAXIMUM SIDE BURNER
WEIGHT = 15 lbs
POIDS LATÉRALMAXIMUM DE
BRÛLEUR = 6,8 kg
SIDE BURNER
LE BRÛLEUR DE CÔTÉ

MATCH LIGHTING THE MAIN BURNERS:
1. Open lid before lighting.
2. Make sure all control knobs are in the “OFF” position.
3. Place a paper match in the end of the matchlighter. Strike the match
and place through lighting hole in the left hand side of the grill to
approximately1/2”(1to2cm)fromtheburner.
4. Turn on the FAR LEFT burner control knob to the “HIGH” position. The
burner should light within 5 seconds.
5. If the burner does not light, turn the control knob to “OFF” and wait
5 minutes for gas to dissipate and repeat lighting procedure.
6. Once lit, light adjacent burners in sequence by pressing in and rotating the control knob to the “HIGH”
position.
7. If the burner does not light within the first few attempts of match lighting, there is a problem with the
gas supply. Turn off the gas at the burner and cylinder. DO NOT attempt to operate the grill until the
problem is found and corrected.
Note: If burner does not light or flame is too low, See “Trouble Shooting” section of the owners
manual.
LIGHTING THE SIDE BURNER:
1. Open lid before lighting side burner.
2. Make sure control knob is in the “OFF” position.
3. Push and hold down side burner control knob and SLOWLY (2 to 3
seconds) turn to “IGNITE”. You should hear the igniter click.
Note: Step 3 may need to be repeated 2-3 times to light side burner.
4. If ignition does NOT occur in 5 seconds, turn control knob to “OFF”, wait
5 minutes to allow gas to dissipate and repeat lighting procedure.
5. If burner does not ignite using the igniter, see “Match Lighting the Side Burner” section.
6. To turn off, turn control knob clockwise until it locks in “OFF” position.
Note: If burner does not light or flame is too low, See “Trouble Shooting” section of the owners
manual.
MATCH LIGHTING THE SIDE BURNER:
1. Open the lid to the side burner before lighting.
2. Turn the burner control knob to “OFF”.
3. Strikeandcarefullyplaceamatchapproximately1/2”(1to2cm)fromtheburner.
4. Turn the side burner control knob to the “HIGH” position. The burner should light within 5 seconds.
5. If the burner does not light, turn the control knob to “OFF” and wait 5 minutes for gas to dissipate and
repeat lighting procedure.
6. If the burner does not light within the first few attempts of match lighting, there is a problem with the
gas supply. Turn off the gas at the burner and cylinder. DO NOT attempt
to operate the grill until the problem is found and corrected.
Note: If burner does not light or flame is too low, See “Trouble Shooting”
section of the owners manual.
 Note: Observeflameheightwhenlit:FlameshouldbeaBlue/Yellow
color between 1”–2” when burner is on “HIGH”.
See section in manual on burner adjustment to adjust flame.
10
Lighting Hole
Matchlighter
IGNITION BURNER
l'ALLUMEUR DU BRÛLEUR
Read Instructions Before Lighting:
1. Open lid during lighting.
2. P
ush and hold down the IGNITION
BURNER control knob and turn SLOWLY
(2 to 3 seconds) to "HIGH". Y
ou should
hear the ignitor click.
3.
If ignition does not occur in 5 seconds,
turn the burner control "OFF",
wait
5 minutes and repeat lighting procedure.
Ve
uillez Lire les Instructions
Avant l'Allumage:
1. Ouvrez le couverc
le pendant l'allumage.
2. A
ppuyez sur le bouton de commande
de l'ALLUMEUR DU BRÛLEUR et
maintenez-le enfoncé et tournez
LENTEMENT (2 à 3 secondes) pour
« ÉLEVÉ ».
On devrait entendre le bruit
de l'allumeur.
3. S
i rien n'arrive après 5 secondes,
placez le bouton de commande à la
position « ÉTEINT»,
attendez 5 minutes
pour permettre au gaz de se dissiper et
répétez la procédure d'allumage.
FOR OUTDOOR
USE ONLY
UTILISER
UNIQUEMENT
A L’EXTÉRIEUR
SIDE BURNER
LE BRÛLEUR DE CÔTÉ
WWW.BRINKMANN.NET
800-527-0717
ForAccessories, Parts or Assistance,
Callor Visit our Website
Appelez-nousou visitez notre site pour obtenir
desaccessoires, des pièces ou de l'aide
O
F
F
É
T
E
I
N
T
L
O
W
F
A
E
I
BL
H
I
G
H
É
L
E
V
É
O
F
F
É
T
E
I
N
T
L
O
W
F
A
E
I
BL
H
I
G
H
É
L
E
V
É
O
F
F
É
T
E
I
N
T
L
O
W
F
A
E
I
BL
H
I
G
H
É
L
E
V
É
O
F
F
É
T
E
I
N
T
L
O
W
F
A
E
I
BL
H
I
G
H
É
L
E
V
É
MAXIMUM SIDE BURNER
WEIGHT = 15 lbs
POIDS LATÉRALMAXIMUM DE
BRÛLEUR = 6,8 kg
SIDE BURNER
LE BRÛLEUR DE CÔTÉ

BREAKINGINYOURGRILL:
• Inmanufacturingandpreservingthecomponentsofyourgrill,oilresiduemaybepresentonthe
burners and cooking surfaces of your grill.
• Beforecookingonyourgrillforthefirsttimeyoushouldpreheatitfor15minuteson“HIGH”toburn
off these residual oils.
PREHEATING THE GRILL:
• Priortoeachuse,itisrecommendedthatyoupreheatyourgrill.Thisensuresthatthegrillingsurfaces
are at the desired temperatures to sear the food sugars when cooking. After lighting your grill, set the
main burner control knobs to the “HIGH” position for 5 to 10 minutes. Close the lid during the preheat
period.
CONTROLLINGFLARE-UPS/GREASEFIRES:
• Flare-upsareapartofcookingmeatsonagasgrill.Thisaddstotheuniqueflavorofcookingonagas
grill. Use caution when opening the lid as sudden flare-ups may occur. Excessive flare-ups can over-
cook your food and cause a dangerous situation for you and your grill. Excessive flare-ups result from
the build-up of grease in your grill. If this should occur, DO NOT pour water onto the flames. This can
cause the grease to splatter and could result in serious burns or bodily harm.
• Ifgreasefireoccurswhilelidisopen,leavelidopen,turnburnerknobsto“OFF”,turnoffLPcylinder
valve. If possible, relocate food to a different section of cooking grate and allow grease to burn out or
smother the flames with baking soda.
• Ifgreasefireoccurswhilelidisclosed,leavelidclosed,asasuddenburstofairmayincreaseflames.
Turn burner knobs to “OFF”, turn off LP cylinder valve. Allow grease to burn out.
• Neverpourwateronagreasefireasgreasemaysplatter/spreadandcouldresultinbodilyinjuryor
property damage.
• Ifgreasefiredoesnotquicklyburnoutorthefireisgrowing/spreading,usetypeBCdrychemicalfire
extinguisher or smother with dirt, sand or baking soda. Closing the lid to extinguish a grease fire is not
possible.
TOMINIMIZEFLARE-UPS:
• Trimexcessfatfrommeatspriortocooking.
• Cookmeatswithhighfatcontents(chickenorpork)onLowsettingsorindirectly.
• Ensurethatyourgrillisonlevelgroundandthegreaseisallowedtoevacuatethegrillthroughthedrain
holeinthebottomandintogreasecup/tray.
• Cleangrillfrequentlytominimizegreasebuildup.
INDIRECTCOOKING:
• Indirectcookingistheprocessofcookingyourfoodwithouttheheatsourcebeingdirectlyunderyour
food. You can sear meats over a high flame on one side of the grill while slow cooking a roast on the other
(unlit) side of the grill.
11
OPERATING THE GRILL:
• Readandfollowallwarningsandinstructionscontainedintheprecedingsectionsofthis
manual.
• Neverusecharcoal,lavarocksorwoodbriquetsinagasgrill.Flavoringchipsmustbe
contained in a metal smoking box to contain ash and prevent fires.
• DONOTcovercookinggratesorothercomponentswithaluminumfoil,asthisblocks
ventilation and damage to grill or personal injury may occur.
• DONOTleaveyourgrillunattendedwhile“ON”orinuse.
• DONOTmovegrillwheninuse.
• DONOTusewateronagreasefire.Closingthelidtoextinguishagreasefireisnotpossible.
Use type BC dry chemical fire extinguisher or smother with dirt, sand or baking soda.
• Nevercookonthegrillwithoutthegreasecup/trayinplace.
WARNING

12
ROTISSERIECOOKING:
• Yourgrillwaspre-drilledfromfactorytoincludemountingholesforarotisserie(soldseparately).Do
not use a rotisserie not specifically manufactured for this grill.
• Readandfollowallinstructionsprovidedwiththerotisserie.Saveinstructionsforfuturereference.
• Donotusethesideburnerwhenusingarotisserie.
• Readinstructionsonlightingyourgrilltolightthesideburner.
• Neverclosethesideburnercoverwhentheburnerislit.
• Usea10”diameterpotorsmallerthatdoesNOThaveanextendedhandlewhencookingontheside
burner. Center pot over burner.
• Neverplacemorethan15poundsonthesideburner.Thesideburnerisnotconstructedtohold
weightexceeding15pounds.
• Usecautiontoavoidbumpinggrill,sideburnerorpottopreventpotfromspillingcontentspossibly
leading to severe burns.
• DONOTusesideburnertodeepfryfoodinoiltoavoiddangersassociatedwithoilignitingcreating
a very dangerous situation.
• WhenusinganACcurrentrotisserie,itmustbeelectricallygroundedinaccordancewithlocal
codes, or in the absence of local codes:
 • IntheUS:TheNationalElectricalCode–ANSI-NFPANo.70–LatestEdition
 • InCanada:theCanadianElectricalCode–CSAC22.1
• TheRotisserieisequippedwithathreeprongedplugforyourprotectionagainstelectricalshock.
This plug should be plugged directly into a properly grounded 3 prong receptacle. Never cut or
remove the grounding plug. Any extension cord must also have a 3 prong receptacle.
• Allelectricalsupplycordsshouldbekeptawayfromwaterandanyhotsurfacesofthegrill.
TURNING OFF THE GRILL:
1. Turn off the cylinder valve.
2. Turn all burner control knobs to the “OFF” position.
Note: Turn off LP cylinder first to prevent gas from being left in the system
under pressure.
CAUTION: The cylinder valve should always be in the off, or closed, position
when the grill is not in use.
THE SIDE BURNER:
• Thesideburnercanbeusedtopreparesidedishessuchasbeans,potatoes,corn,ortowarm
sauces.
• Theburnervalvecanbeadjustedfromhightolowdependinguponyourcookingdemands.
To turn off the cylinder valve, turn
knob clockwise until it stops.
USING OTHER FEATURES OF THE GRILL:
WARNING
WARNING

PROPER CARE & MAINTENANCE:
WARNING: If a bristle brush is used to clean any of the cooking surfaces, ensure no loose bristles
remain on the cooking surfaces prior to grilling as loose bristles may attach to food.
CLEANING INTERIOR OF GRILL:
• Werecommendcleaningofffoodresidueimmediatelyaftercookingbygentlyscrubbinggrateswith
wire bristle brush and then turning burners to HIGH for approximately 5 minutes.
WARNING: DO NOT leave grill unattended when grill is on. Wear oven mitts to protect from burns.
• Theheatfromtheburnerswillburnoffmostfood/greaseresiduefromgrates&heattentsandturnit
to an ash like substance which will fall to the bottom of the firebox or grease tray. After the grill cools
(approximately 30 minutes) remove grates and heat tents and brush the ash and any grease out of
the firebox. Clean and replace grease cup. Inspect the heat tents for damage or deterioration before
reinstalling in the grill. (Replacements can be ordered by calling 800-527-0717.)
• Washthegratesandheattentswithamilddetergentandrinsewithhotwaterperiodicallyifdesired.
CAUTION: DO NOT allow ash residue to remain on the grease tray or firebox as it could block proper
grease drainage of the grill.
INTERIOR OF GRILL LID:
• Smokewillaccumulateinsidegrilllidandmayflakeontoyourfood.Cleantheinsideofthegrilllidwith
scrubbrushandbakingsoda/watersolution.Drythoroughly.Donotmistakethisforpaint.Theinterior
of gas grill lids are not painted.
MAINTAINING EXTERIOR OF GRILL:
• Toprotectyourgrillfromexcessiverust,theunitmustbekeptcleanandcoveredatalltimeswhennot
in use.
• Paintedsurfaces.Washwithmilddetergentornon-abrasivecleanerandwarmsoapywater.
• Stainlesssteelsurfaces.Tomaintainyourgrill’sappearance,washwithmilddetergentandwarm
soapy water and wipe dry with a soft cloth after each use. Baked-on grease deposits may require the
use of an abrasive plastic cleaning pad. Use only in direction of brushed finish to avoid damage. Do
not use abrasive pad on areas with graphics. Car wax may help protect the exterior finish of your grill.
• Porcelainsurfaces.Becauseofglass-likecomposition,mostresiduecanbewipedawaywitha
solution of baking soda and water or specially formulated cleaner. Use non-abrasive scouring powder
such as baking soda for stubborn stains.
• Plasticandrubberparts.Washwithwarmsoapywaterandwipedry.Donotusecitrisol,abrasive
cleaners, degreasers or a concentrated grill cleaner on plastic parts. Damage to and failure of parts
can result.
RUST:
• Discoloration,rustandrustpitscanoccurasaresultofhighcookingtemperatures,acidicmarinades,
grease fires and exposure to coastal climates or other natural elements.
• Rustspotsontheinteriorsurfacecanbebuffed,cleaned,thenlightlycoatedwithvegetableoilor
vegetable oil spray to minimize rusting.
• Neverusecleanerscontainingchlorineorstoreswimmingpoolsuppliesorchemicalsincart
compartment as chlorine promotes rust.
13

BURNER CLEANING AND MAINTENANCE:
• Keeptheappliancefreeandclearofcombustiblematerials,gasolineandotherflammablevaporsand
liquids.
• Keeptheventilationopeningsofthecylinderenclosurefreeandclearofdebris.
• Visuallycheckburnerflamesforproperoperation(seepictorialin“BurnerAssembly/Maintenance”
under Proper Care and Maintenance). Spiders or other insects can nest in the burner causing gas
blockage.
• Forsafegrillingandpeakperformanceofyourgrill,performthesechecksatleasttwiceperyearor
after extended periods of storage.
• Besuretotightenupallhardware(nuts,bolts,screws,etc.)atleasttwiceperyear.
CAUTION: Some parts may contain sharp edges. Wear protective gloves if necessary.
• Removethecookinggrills,heatdistributionplates,andburnersfrominsideyourgrill.Useabrush
with hot water and detergent to remove excess residue. NEVER use a commercial oven cleaner.
Rinse completely with water. Towel dry and replace all components as described in the assembly
instructions.
BURNER ASSEMBLY/MAINTENANCE:
• Althoughyourburnersareconstructedofstainlesssteel,
they may corrode as a result of the extreme heat and acids
from cooking foods. Regularly inspect the burners for cracks,
abnormal holes, and other signs of corrosion damage. If found,
replace the burner.
• DONOTblockventilationareasinsides,backorcart
compartment of grill. Burner tubes can become blocked by
spiders and other insects building their nests. Blocked burner
tubes can prevent gas flow to the burners and could result in
a burner tube fire or fire beneath the grill. To clean the Burner
Assemblyfollowtheseinstructionstocleanand/orreplaceparts
of burner assembly or if you have trouble igniting the grill.
1. Turn gas off at control knobs and LP cylinder tank valve.
2. Remove cooking grills and heat distribution plates.
3. Remove bolt and nut from each burner “foot” using a
screwdriver.
4. Carefully lift each crossover channel up and away from burners.
5. Carefully lift each burner up and away from valve openings.
6. Use a narrow bottle brush or a stiff wire bent into a small hook
to run through each burner tube or use compressed air to blow
into burner tube and out the flame ports. Check each port to
make sure air comes out each hole.
CAUTION: Wear eye protection when using compressed air.
7. Use a wire brush to clean the entire outer surface of burner to
remove food residue and dirt.
8. Check burner for damage, if any cracks or holes are
found replace burner.
9. Install burner in grill and carefully align crossover channels
between burners and orient burners CORRECTLY.
IMPORTANT: Burner opening must slide over valve nozzle.
10. Replace bolt and nut in each burner and crossover channel.
Note: Follow the “Gas Leak Testing” section of this manual.
Relight burners to verify proper operation.
11. Replace heat distribution plates and cooking grills.
14
Debris
PROPER VALVE TO BURNER ALIGNMENT
Valve Nozzle
Burner Opening
Bolt
Crossover Channel
Nut

BEFORE STORING YOUR GRILL:
• Ensurethatthecylindervalveisfullyclosed.
• Cleanallsurfaces.Lightlycoattheburnerswithcookingoiltopreventexcessrusting.
• Ifstoringthegrillindoors,disconnecttheLPtankandleavetheLPtankOUTDOORS.
• Placedustcaponcylindervalveoutletwheneverthecylinderisnotinuse.Onlyinstallthetypeofdust
cap on the cylinder valve outlet that is provided with the cylinder valve. Other types of caps or plugs
may result in leakage of propane.
• Checkandcleanburnerpriortouseafterstoring,atthebeginningofgrillingseasonorafteraperiod
of not being used. Spiders and insects like to build nests in burner tubes (especially during colder
months). Blocked burner tubes can prevent gas flow to the burners and could result in a burner tube
fireorfirebeneaththegrill.See“BurnerAssembly/Maintenance”underProperCareandMaintenance.
• Ifstoringthegrilloutdoors,coverthegrillwithagrillcoverforprotectionfromtheweather.
• Normalflameshouldbesoftbluewithyellowtipsbetween1in.-2in.whenburnerison“HIGH”.
Depending on elevation, burner air shutter may need to be adjusted to obtain correct air to fuel ratio.
• Toadjustairshutter,loosensetscrewandrotateairshuttertodesiredpositiontoachievenormal
flame. Tighten set screw after adjustment is made. Relight the grill to observe flame. Incremental
adjustments may be needed to achieve a good flame.
BURNER ADJUSTMENT
15
• Nevermoveagrillwhenhotorinuse.
• Makesurethatcylindervalveisclosedandburnerknobsareintheoffposition.
• DONOTstoreaspareLPgascylinder(filledorempty)underornearthegrill.
• Neverstoreflammableliquidsorspraycanistersunderornearthegrill.
• Iftheoutdoorcookinggasapplianceisnotinuse,thegasmustbeturnedoffattheLPgas
supply cylinder.
• Storageofanoutdoorcookinggasapplianceindoorsispermissibleonlyifthecylinderis
disconnected and removed from the outdoor cooking gas appliance.
• Cylindersmustnotbestoredinabuildingorenclosure,includinggaragesandsheds.
• Cylindersmustbekeptoutofreachofchildren.
TRANSPORTING AND STORAGE:
• DONOTattempttoadjustburnerairshutteruntilgrillhascooleddownforapproximately
30 minutes. Failure to do so could cause severe burns.
Soft blue flame with yellow tips
INCORRECTCORRECT
Wavy with yellow flames
Set Screw
WARNING
WARNING

16
TROUBLE SHOOTING:
Problem Possible Cause Prevention/Cure
Burner will not light LP gas tank valve is closed Make sure regulator is securely attached to the LP gas tank, turn LP
gas tank valve to “OPEN”
LP gas tank is low or empty Check if LP gas tank is empty. If empty, replace or rell
LP gas leak 1. Turn LP gas tank valve to “CLOSED”
2. Wait 5 minutes for gas to clear
3. Follow “Leak Testing” in the owner’s manual
Coupling nut and regulator not fully connected See section on “Connecting Hose and Regulator”
Obstruction of gas ow 1. Clear burner tubes
2. Check for bent or kinked hose
Burner may not be properly seated Reseatburnerandvalve.Referto“BurnerAssembly/Maintenance”
instructions
Spider webs or insect nest in venturi Clean venturi and burner tube
Burner ports clogged or blocked Clean burner ports
Battery needs to be changed Replace the battery (follow assembly step for inserting battery)
Wires or electrode covered with cooking residue Cleanwireand/orelectrodewithrubbingalcohol
Electrode and burners are wet Wipe dry with cloth
Electrode cracked or broken - sparks at crack Replace electrode
Wire loose or disconnected Reconnectwireorreplaceelectrode/wireassembly
Wire is shorting (sparking) between ignitor and
electrode
Replaceignitorwire/electrodeassembly
Bad ignitor Replace ignitor
Grill does not get hot
enough
Out of gas Replace or rell LP gas tank
Flow limiting device may have been activated 1. Mini Reset:
a. Turn control knobs and LP gas tank valve to “OFF”
b. Wait one minute and relight grill per “Lighting Instructions”
2. If ames are still too low, perform a Full Reset
Full Reset:
a. Turn control knobs and LP gas tank valve to “OFF”
b. Disconnect regulator from propane tank
c. Inspect LP cylinder rubber seal
d. Wait 1 minute
e. Reconnect regulator and perform “Leak Testing” on all
connections.
f. Light grill per “Lighting Instructions”
Irregular flame pattern.
Flame does not run full
length of burner
Burner ports are clogged or bocked Clean burner ports
Flame is yellow or orange New burner may have residual manufacturing
oils
Burn grill for 15 minutes on “HIGH” with the lid closed
Spider webs or insect nest in venturi Clean venturi and burner tube
Food residue, grease, etc. Clean burner
Poor alignment of valve to burner venturi Assure burner venturi is properly engaged with valve
Air shutter on burner needs adjustment See section on “Burner Adjustment”
To see trouble shooting or assembly videos, visit us at

17
Problem Possible Cause Prevention/Cure
Flame blow out High or gusting winds Do not use grill in high winds
Low on LP gas Replace or rell LP gas tank
Burner holes may be obstructed Referto“BurnerAssembly/Maintenance”instructions
Flow limiting device tripped Refer to “Regulator Resetting Procedure”
Flare-up Grease buildup Clean all grill parts per “Proper Care and Maintenance” instructions
Excess fat in meat Trim fat from meat before grilling
Excessive cooking temperature Adjust (lower) cooking temperature
Grease fire Grease trapped by food buildup around burner
system
1. Turn control knobs and LP gas tank valve to “OFF”
2. Leave lid in closed position and let re burn out
3. After grill cools, remove and clean all parts per “Proper Care and
Maintenance” instructions
Flashback (fire in burner
tubes) / knobs melting
Burnerand/orburnertubesareblocked Cleanburnersand/orburnertubes
Inside of lid is peeling
(like paint peeling)
Baked on grease buildup has turned into car-
bon and is aking off
Clean thoroughly per “Proper Care and Maintenance” instructions
GRILL COOKING TIPS:
CLEANLINESS:
• Alwayswashhandsthoroughlywithsoapandhotwaterpriortohandlingfoodandafterhandlingraw
meat, uncooked poultry or seafood.
• Whenusingaplattertocarryrawmeat,uncookedpoultryorseafoodtothegrill,makesuretowash
the platter thoroughly with soap and hot water before placing cooked foods back on the platter or use
different platters for raw and cooked foods.
• Neverusethesameutensilswhenhandlingrawmeat,uncookedpoultryorseafoodunlessyouwash
the utensils thoroughly with soap and hot water.
• Neverre-usemarinadefromrawmeatoruncookedpoultryonfoodsthathavebeencookedandare
ready to be served.
GRILLING TO PROPER TEMPERATURE:
• Useameatthermometertobesurefoodhasreachedasafeinternaltemperature.
• TheUSDArecommendstheminimumtemperaturebereachedforthefollowingfooditems:
HELPFUL HINTS:
• Ifyoupre-cookmeatorpoultry,dosoimmediatelybeforegrilling.
• Neverdefrostmeatatroomtemperatureoronacountertop.
• Refrigerateleftoverswithin2hoursoftakingfoodoffthegrill.
• Foradditionalinformation,pleasephonetheUSDA’stollfreeMeat&PoultryHotlineat800-535-4555.
Chops ................... 145°F(62.8°C)
Ground Meat .............. 160°F(71°C)
Pork ..................... 145°F(62.8°C)
Poultry ................... 165°F(73.9°C)
Roasts ................... 145°F(62.8°C)
Seafood .................. 145°F(62.8°C)
Vegetables................ 145°F(62.8°C)

18
Make sure you have all items listed under PARTS LIST and PARTS BAG CONTENTS before
you begin the installation process.
PARTS BAG CONTAINS:
ASSEMBLY INSTRUCTIONS:
22 M6 X 12 mm Bolts (Black)
20 M6 Star Washers
2 M6 X 12 mm Bolts (Silver)
2 M4 X 10 mm Bolts
8 #10 Self-Tapping Screws
2 M6 Washers
1 M4 Washer
1 M4 Nut
2 Wheel Washers
Qty. Qty.
M6 X 12 mm Bolts (Black)
Wheel Washers
M6 Star Washers
M6 X 12 mm
Bolts (Silver)
M6 Washers
M4 X 10 mm
Bolts
M4 Washer
#10 Self-Tapping Screws
M4 Nut

1 Front Right Cart Leg
2 Left Cart Braces
1 Right Cart Brace
1 Rear Cart Brace
1 Tank Support Bracket
1 Tank Retention Bracket
1 Carriage Bolt
1 Wing Nut
1 Tank Brace
2 Wheel Axle Bolts
2 Cotter Pins
2 Wheels
1 Side Burner
1 Grease Cup
PARTS LIST:
1 Grill Body Assembly
1 Left Side Table Assembly
1 Right Side Table Assembly
1 Side Burner Grate
1 Bottle Opener
1 Hood Handle
1 Grease Tray
1 Warming Rack
2 Cooking Grills
3 Heat Distribution Plates
1 Upper Cart Front Panel
1 Lower Cart Front Panel
1 Rear Left Cart Leg
1 Front Left Cart Leg
1 Rear Right Cart Leg
1
2
3
4
5
6
7
8
9
10
11
16
17
18
19
21
22
23
20
24
12
13
14
15
25
26
27
28
29
WERECOMMENDTWOPEOPLEWORKTOGETHERWHENASSEMBLINGTHISUNIT.
The following tools are required to assemble this Brinkmann Heavy-Duty Gas Grill:
• PhillipsHeadScrewdriver
READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY
BEFORE ASSEMBLING OR OPERATING YOUR GRILL.
To see trouble shooting or assembly videos, visit us at
19