Bristan Claret CLR BASNW C/WHT Mounting instructions

Installation Instructions
and User Guide
Claret Tap Range
Models Covered:
CLR BASNW C/WHT
CLR 1HBF C/WHT
CLR WMBAS C
CLR WMBF C/WHT
CLR WMBSM C
Please keep this booklet for future
reference.
Installer, when you have read these
instructions please ensure you leave
them with the user.

2Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Thank you for choosing Bristan, the UK’s leading taps and showers expert.
We have designed this product with your enjoyment in mind. To ensure that it works
to its full potential, it needs to be fitted correctly. These fitting instructions have been
created to give you all of the information you need and, if you need any further help,
please do not hesitate to contact us.
Contents
• Important Safety Information 3
• Specifications 4
• Dimensions (mm) 5-6
• Installation 7-12
• Maintenance 13-14
• Troubleshooting 15
Contents

3
Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Important Safety Information
• Please read these instructions thoroughly
and retain for future use.
• All products manufactured and supplied
by Bristan are safe provided they are installed,
used correctly and receive regular maintenance
in accordance with these instructions.
• If you are in any doubt about your ability
to install this product safely you must employ
the services of an experienced qualified
plumber/electrically qualified person.
• This product has been tested to the Water
Regulations Advisory Scheme (WRAS) and
satisfies the requirements of the Water Supply
(Water Fittings) Regulations 1999 and current
bylaws. For full Installation Requirements &
Notes (IRN) please visit wras.co.uk/directory.
• Warning: Before starting
any installation please consider the
following: before drilling into walls, check that
there are no hidden electrical wires, cables or
water supply pipes. This can be checked with
the aid of an electronic detector.
• If power tools are used do not forget to:
- Wear eye protection
- Unplug equipment after use
• Important: Remember to turn o the mains
water supply before connecting to any existing
pipe work.
• Warning: Before installing
the new fitting it is essential that
you thoroughly flush through the pipework in
order to remove any remaining swarf, solder,
etc. Failure to carry out this procedure could
cause problems or damage to the workings of
the fitting.
• We recommend isolation valves to be fitted to
the inlet water supplies to ensure ease of future
maintenance.
• Full access must be made available for future
maintenance/servicing purposes.
• Take care when handling the ‘flexible
connecting pipes’, do not bend, twist or crush
them. Only tighten the pipes by hand.
• Do not crush or kink the shower hose, this
could damage the hose and cause leaks.
This product must not be modified in any way as
this will invalidate the guarantee.
If in doubt, contact a registered plumber or your
Local Water Authority or the Secretary of the
Institute of Plumbing, address as follows:-
The Institute of Plumbing,
64 Station Lane,
Hornchurch,
Essex,
RM12 6NB, Tel: [phone]

4Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Specifications
Product Code Working Pressure
Min Max
1 Hole Bath Filler 1.5 5.0
Basin Mixer (No waster) 0.2 5.0
Wall Mounted Basin Mixer 1.0 5.0
Wall Mounted Basin Filler 0.3 5.0
Wall Mounted Bath Shower
Mixer
1.0 5.0
Maximum static pressure- 10.0 bar
NOTE:- Nominally equal (balanced) inlet supply pressures are recommended for
optimum Performance of mixer taps.
Designed to comply with BS EN 200 for single taps/ combination taps for water
systems of type 1 and 2 general technical specifications; and to be used within
systems designed to BS 6700.
BS 6700 recommends the temperature of stored water should never exceed
65° C. A stored water temperature of 60° C is considered sucient to meet all
nominal requirements and will minimise the build up of lime scale in hard water
areas.

5
Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Dimensions (mm)
50
95
170
50
90
105
60
175
125
60 55
Basin Mixer
1 Hole Bath Filler

6Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Dimensions (mm)
50 60
190
127
122
180
330
120
50
58
197
145
100 100
220
58
147
50
185
50 62
182
100
128
122
120
100
210
110
100
5040
20150
140
118
115 40
Wall Mounted Basin Mixer
Wall Mounted Bath Filler
Wall Mounted Bath Shower Mixer

7
Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Installation
1. Identify all components are present
prior to starting installation.
2. Ensure that the washer (9) is fitted
to the underside of the tap body
(7) before fitting to the basin/bath.
Secure the ‘C’ shaped rubber washer
(10) and metal plate (11) into position
on the underside of the basin/bath,
using the threaded rods and nuts
(12).
3. Fit the inlet connection pipes (13) by
hand only (DO NOT OVERTIGHTEN)
to the fitting and connect the hot
and cold supplies.
4. Connect the hot and cold water
supplies to the connecting pipes.
5. Turn on the water and fully open
the mixer, allowing it to run for a
few minutes and check all joints and
connections for any leaks.
Basin Mixer (No Waste) & 1 Hole
Bath Filler
1. Grub Screw x1
2. Lever Handle x1
3. Lever Handle Spacer x1
4. Shroud x1
5. Cartridge Retaining Nut x1
6. Cartridge x1
7. Tap Body x1
8. Anti-Splash Assembly x1
9. Washer x1
10. ‘C’ Shaped Rubber Washer x1
11. ‘C’ Shaped Metal Plate x1
12. Fixing Rods x2
13. Connecting Pipes x2

8Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Installation Cont.
Wall Mounted Basin Mixer/ Bath
Filler
1. Handle x1
2. Cartridge Retaining Nut x1
3. Shroud x1
4. Cartridge x1
5. Mixer Body Sleeve x1
6. O-Ring x1
7. Mixer Body x1
8. Concealing Plate x1
9. Concealing Plate x1
10. O-Ring x1
11. O-Ring x1
12. Screw & Wall Plug Pack x1
13. Nut & Olive x1
14. Spout Connection Kit x1
15. Locking Grub Screws x2
16. Spout Grub Screw x1
17. Spout x1
18. Anti-Splash x1
19. Handle Grub Screw x1

9
Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Installation Cont.
1. Identify all components are present
prior to starting installation using
the diagram overleaf, and be sure to
refer to the dimensions on pages 4
& 5 for minimum and maximum wall
cavity depths.
2. Oer the mixer body (7) up to the
wall and once in the desired position,
mark and drill holes for the fixings
(12)
IMPORTANT: Before drilling into walls,
check that there are no hidden electrical
wires, cables or water supply pipes.
This can be checked with the aid of
an electronic detector. If power tools
are used do not forget to wear eye
protection & unplug equipment after
use.
3. Fit the mixer body (7) to the wall
and connect water supplies using the
nut and olive (13). Any further tiling
required, should be completed at this
stage.
NOTE: The tiles should not restrict
access to the valve in order to allow for
servicing of the product if necessary.
4. Push concealing plate (8). complete
with seal (9), over the valve body and
push towards the tiled surface.
TIP: Use a thin line of silicone based
sealant around the back edge of the
concealing plate to create a tight water
seal.
5. Push the spout (17) on to the pre-
fitted spout connection kit (14);
ensuring that both O-rings locate
within the spout, and both of the
locking grub screws (15) fit into
place, via the 2 small holes in the
concealing plate (8). Tighten grub
screw on the underside of spout to
secure into place.
6. Turn on the water and fully open
the mixer, allowing it to run for a
few minutes and check all joints and
connections for any leaks
Wall Mounted Basin Mixer/ Bath Filler

10 Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Installation Cont.
Wall Mounted Bath Shower Mixer
1. Handle x1
2. Shroud x1
3. Retaining Nut x1
4. Cartridge x1
5. Sleeve x1
6. 0-Ring x1
7. Mixer Body x1
8. Concealing Plate x1
9. Plate Seal x1
10. 0-Ring x1
11. O-Ring x1
12. Handset Holder x1
13. Hose x1
14. Handset x1
15. Spout Connections x1
16. Spout Locking Pins x1
17. Spout x1
18. Grub Screw x1
19. Anti-Splash x1
20. Diverter Assembly x1
21. Diverter Knob x1
22.Grub Screw x1
23.Screw & Wall Plug Pack x1
24.Nut & Olive x3