Bristan Z2 BIB C Wiring diagram

1
IMPORTANT
Prior to drilling into
walls check there are
no hidden electrical wires,
cables or water supply
pipes
1
5
6
2
4
3
1
Pack Contents
Installation Instructions
& User Guide
Prior to Installation
Installation
Please leave these instructions
with the end user
Product Code: Z2 BIB C (D5)
All products manufactured and supplied by Bristan are safe provided
they are installed, used correctly and receive regular maintenance in
accordance with these instructions.
This product has been tested to the Water Regulations Advisory
Scheme (WRAS) and satisfies the requirements of the Water Supply
(Water Fittings) Regulations 1999 and current bylaws.
For full Installation Requirements & Notes (IRN) please visit
wras.co.uk/directory.
We recommend isolation valves to be fitted to the inlet water
supplies to ensure ease of future maintenance.
Before installing these taps the water supply must be
thoroughly flushed in order to remove any swarf, solder etc.
This product must not be modified in any way as this will
invalidate the guarantee.
If power tools are used do not forget to:
- Wear eye protection
- Unplug equipment after use
If in doubt, contact a registered plumber or your Local Water
Authority or the Secretary of the Institute of Plumbing, address
as follows:-
The Institute of Plumbing,
64 Station Lane,
Hornchurch,
Essex,
RM12 6NB, Tel: [phone]
To replace any spare parts
for your tap, why not
scan the QR Code or
visit www.bristan.com
and search for your product.
Spare Parts
Tools You’ll Need
Crosshead
Screwdriver
Adjustable
Spanner
Pipe Cutter Drill
Pressure
BAR
1.0
5.0
0.2
4.0
2.0 3.0
Maximum Static Pressure: 10.0 bar
Min: 0.5 bar Max: 5.0 bar
Dynamic Water Pressure
1.0
5.0
Pressure
BAR
4.0
2.0 3.0
0
If the supply pressure is above 3 bar, a
pressure reducing valv ed
60˚C
65˚C
60-65˚C
recommended
The Flow Valve is timed and
onds
*This will vary depending on system pressure
Maximum Operating Temperature Inlet Connections
1/2” Male BSP Tap connector
5/Ltr Flow Regulator
Pre-Fitted
x1
x1
Flow
regulator x1
Basket Filter
washer x1
Indices
x2
Red
Blue
Rear access
will be
required
Drill hole in
the wall
Place the plinth over the drilled hole
and fit taps through the wall
bask er
washer into the
tail in the order
shown
Connect
the hot or
cold water
supplies to the
threaded tails.
If the supply
pressure is above
3 bar a pressure
reducing valve
ed
Important 5
Depending on
chosen hot
or cold water
supply e
(supplied)
Please
ensure that
the correct
colour indice
ted
Turn on
water
supply
Turn
on water
supply for a
few minutes and
check all joints and
connections for any
leaks.
Operation
6
The tap will shut o up to
15 ± 5 seconds*
Push down
to get flow of
water

Please use this space for any notes you or your installer may have regarding the installation/
plumbing of this product.
At Bristan, we want to make things as easy as possible for our customers. That’s why we antees on
all our pr ective from the date of purchase, to give you peace of mind.
To start your free guarantee simply scan the QR code and register your product. Alternatively visit
www.bristan.com/register to register your product via a computer.
For full guarantee terms and conditions visit www.bristan.com/guarantees.
Troubleshooting
General Cleaning
Notes
Symptom Cause Remedy
w or
lo w
rate
Partially closed isolation valve. Open isolation valve.
Instantaneous water heater cycles on
w rate or pressure is too
low.
Increase watw rate or
pressure through system.
Head of water is below the
minimum distance required. 5 meters minimum required.
Hot or cold water being dra
elsewhere causing pressure changes
or instantaneous boiler temperature
changes.
Do not use other water outlets when using the taps.
Airlock or partial blockage in the supply
pipework.
Flush through pipework to ensure removal of debris
and any airlocks.
Water
dripping
from taps
This is normal for a short time after using
the taps.
This is caused by residual water tension, the build up
of water in the tap body.
If water continues to drip,
possibly due to the ceramic disc valves
Remove valves and clean, refer to 'Maintenance'
section before starting any maintenance.
Taps do not
turn on
Closed isolation valve. Open isolation valve.
Mains wat.Turn on mains water supply.
3
333
2
1
1
Maintenance - Cartridge Cleaning
Unscrew
the grub
screw
in the
Remove
handle.
Y eated with care to preserve the visible surfaces.
All surfaces will wear if not cleaned correctly, the only safe way to clean your mixer tap is to wipe with a
soft damp cloth. Stains can be removed using washing up liquid. All bath cleaning powders and liquids will
damage the surface of y even the non-scratch cleaners.
Note:Never use abrasive detergents or disinfectants or those containing alcohol, hydrochloric acid or
phosphoric acid.
Prior to doing any
maintenance or
servicing the isolation
valves must be turned
to the
closed/
Important
Pull out
the valve
from the
tap body
Maintenance- Flow Straightener
23
Unscrew w straightener and
soak in descaler.
Replac w straightener
into spout.
Remove
valve from
the casing
Clean the seal
around the
valve and apply
silicon grease
Check that the groove
is clear of any debris
on the inside of valve
casing.
screw driver,
remove the
spring and
spline.
Rinse and leave to
one side.
Assemble the
valve. apply
grease and
place back into
the tap body.
Replace
handle
456
w
straightener