Bristan IRSD1-CP Mounting instructions

Please keep this booklet for future
reference.
Installer, when you have read these
instructions please ensure you leave them
with the user.
Installation Instructions
and User Guide
Infrared Automatic Soap
Dispensor
Models covered: IRSD1-CP, IRSD1-BN,
IRSD1-BZ

2
Contents
Thank you for choosing Bristan, the UK’s leading showers and taps expert.
Your Bristan Soap Dispenser has a non-touch control which uses infrared sensing
technology to detect human presence. Once detected, the spout instantly dispenses a
small amount of liquid soap into the users hands to eliminate unnecessary wastage,
whilst creating a more hygienic washroom solution.
All products manufactured and supplied by Bristan are safe and comply to legislative
requirements. Providing they are installed correctly and receive regular maintenance in
accordance with these instructions your user experience will not be affected.
For a safe and successful installation these instructions should be used as guidance,
thereafter they should be left with the user.
Important Safety Information................................................... 3
Specifications ........................................................................... 3
Product Features...................................................................... 4
Installation Requirements ....................................................... 5
Installation................................................................................ 6-8
Commissioning......................................................................... 9
Operation .................................................................................. 10
Maintenance ............................................................................. 11
Troubleshooting........................................................................ 12-13
Guarantee ................................................................................. 14-15
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

3
Important Safety Information
•Please read these instructions thoroughly and retain for future use.
•All products manufactured and supplied by Bristan are safe provided they are installed,
used correctly and receive regular maintenance in accordance with these instructions.
• If you are in any doubt about your ability to install this product safely you must
employ the services of an experienced qualified plumber.
•Warning: Do not operate the product if you suspect it is frozen. Do not site it where
it might be subjected to freezing conditions.
•Remove all packaging and check the contents for damage before starting installation.
•Before starting any installation please consider the following: before drilling into walls,
check that there are no hidden electrical wires, cables or water supply pipes. This can
be checked with the aid of an electronic detector.
•If power tools are used do not forget to: - Wear eye protection
- Unplug equipment after use
•This product must not be modified in any way as this will invalidate the guarantee.
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.
Recommended Usage
Domestic Heavy
Commercial
Light
Commercial Health Care
Specifications
Sensing Range: 0-8 cm
Activation Time: 0.5-1s
Power Supply: AC: 230V
DC: 1.5V (4 x AA alkaline batteries - Not Supplied)
Bottle Capacity: 1.6 litres
Ambient Temperature: Normal Temperature
Viscosity of liquid soap: 100-3500cp (mpA ·s)

4
Product features
More Hygienic
The proximity sensor removes the need
to touch the spout, reducing the spread of
germs and reducing the chance of cross
infection.
Battery Override
Your infrared soap dispenser is supplied
with a back up battery pack.
In the event of a power failure, the product
will automatically switch to battery
operated mode to ensure the spout
continues to function.
Low Battery Warning
When the batteries run low and the
power falls below 3.9V the sensor light
will flicker to indicate the batteries are
running low and need replacing.
When the batteries are exhausted the
sensor light will not light up.
Sensor

5
Installation Requirements
Electrical Connections
Regulations: The electrical installation
must be carried out in accordance with
the national electrical regulations and
installed by a qualified person.
Safety: In the interests of electrical safety
a 30 mA residual current device (R.C.D not
supplied) should be installed in the supply
circuit. This may be part of a consumer
unit or a separate unit.
Before starting work on the electrical
supply ensure the power supply is
isolated.
DO NOT allow the supply cord to contact
hot surfaces. The cord should be safely
routed and secured by cable clips.
Connections: The power supply must be
permanently connected to the fixed wiring
of the mains supply using the factory fitted
supply cord, via a switched fused spur off
the ring main.
The wires in the mains lead are coloured
in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains
lead of this appliance may not correspond
with the coloured markings identifying the
terminals in your connection unit proceed
as follows;-
The wire which is coloured blue must
be connected to the terminal which is
marked with the letter ‘N’ or is coloured
black.
The wire which is coloured brown must
be connected to the terminal which is
marked with the letter ‘L’ or is coloured
red.
Fuse: This following fuse size should be
used.
Model Fuse Size (AMPS)
IRSD1-CP 3
IRSD1-BN 3
IRSD1-BZ 3
Supply Cord Replacement
If the supply cord is damaged, it must be
replaced by a genuine Bristan supply cord.
Contact Bristan Customer Services on
0844 701 6273 to request new spare parts.
N L

6
Installation
1. Fit The Spout
Fit the spout to the sink / basin ensuring
the dispensing cable and sensor cable
are threaded through the hole in the sink
/ basin.
2. Secure Spout to Sink / Basin
Screw the metal backnut onto the thread
of the spout upto the underside of the sink
/ basin.
Tighten backnut using a suitable spanner.
2. Fit Wall Brackets
Position the brackets onto the wall
surface and mark the position of the fixing
holes.
Remove the brackets and drill suitable
holes for the wall plugs supplied.
Before drilling into walls, check
that there are no hidden electrical wires,
cables or water supply pipes. This can
be checked with the aid of an electrical
detector:
If power tools are used do not forget to:
- Wear eye protection
- Unplug equipment after use
Fit the wall plugs and position the
brackets into position and secure using
the screws provided.
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.
Dispenser &
Sensor cables
Battery
Wall
Bracket
Bottle Wall
Bracket

7
Installation - cont.
4. Attach Pump to Bottle
Ensure the dispenser tube is located
inside the bottle and push the pump down
firmly onto the bottle until a loud ‘click’ is
heard.
To remove the pump from the bottle press
the release button in on the side of the
pump and pull the pump from the bottle.
5. Connect Sensor Cable and Dispenser
Cable
Connect the sensor cable from the spout
to the sensor cable on the pump. Push
the two connections together and tighten
the connecting ring to ensure the two
connections are locked together.
Connect the dispening cable from the
spout into the top connection on the
pump.
Push the threaded connection of the
dispensing cable into the connection on
the pump and tighten the nut ensuring it
is fully tightened.
A suitable spanner may be used to tighten
the nut.
6. Place Pump into Bracket
The pump has a cut out section which the
wall bracket slots into.
Pump
Dispenser
Tube
Bottle
Power
Cables
Senser
Cables
Dispenser
Cable

8
Installation - cont.
7. Connect Power Supply Cable
Before starting any electrical work
ensure the power supply is isolated.
Wire the electrical power cable into a
switched fused spur off the ring main.
The blue wire should be wired to the
neutral connection and the brown
wire should be connected to the live
connection.
Note: For full electrical requirements see
‘Electrical Connections’ in ‘Installation
Requirements’ section on page 5.
Important: The power lead must be
permanently connected to the fixed wiring
of the mains supply using the factory
supplied power cable.
Plug the power cable into the power cable
on the pump.
8. Inserting Batteries
Remove the battery cover by loosening the
screw in the top of the cover.
Insert 4 x AA batteries into the battery
box ensuring they are inserted the correct
way.
Note: Only use 1.5V AA (LR6) Alkaline
batteries (preferably => 2000mAh for good
battery life).
Replace the battery box cover and tighten
the screw. Insert the battery box into the
holder.
Push the holder into the battery box wall
bracket.
Battery
Case

9
Commissioning
Commissioning Sequence
Before using the soap dispenser for the
first time the following sequence must be
carried out.
Fill the bottle full of liquid soap. Refer to
specification section on page 3 for the
correct liquid soap to be used.
Locate the dispense button on the side of
the pump. Press and hold the button until
soap is dispensed from the spout. This
will ensure the dispenser tube and cable
are full of liquid soap.
Selecting Volume Adjustment
The soap dispenser has four dispense
volume adjustment settings. Each
adjustment setting dispenses a different
volume of liquid soap.
Volume Adjustment
Setting
Volume of liquid
soap (ml)
Low 0.5
Normal 1
Medium 1.5
High 2
To adjust the volume of soap dispensed
follow the steps below.
Locate the volume adjustment switches
under the rubber cover.
Set the switches to the required position
for the desired volume adjustment setting.
Refer to the switch position diagrams.
Dispense
Button
Volume
adjustment
ON
ON
ON
ON
Low: 0.5 ml
Switch 1: Off
Switch 2: Off
Normal: 1 ml
Switch 1: Off
Switch 2: On
Midium: 1.5 ml
Switch 1: On
Switch 2: Off
High: 2 ml
Switch 1: On
Switch 2: On
1 21 21 21 2
Volume Adjustment Switch Positions

10
Operation
Using the Automatic Soap Dispenser
Place the users hands under the spout
within the sensing range.
Once the users hands have been detected
a small amout of liquid soap will be
dispensed from the spout into the users
hands.
Note: The sensing range 0-8cm from the
sensor.

11
General Cleaning
Your fitting has a high quality finish and
should be treated with care to preserve
the visible surfaces. All surfaces will
wear if not cleaned correctly, the only safe
way to clean your mixer is to wipe with a
soft damp cloth. Stains can be removed
using washing up liquid. All bath cleaning
powders and liquids will damage the
surface of your fitting, even the non-
scratch cleaners.
Note: Never use abrasive detergents or
disinfectants or those containing alcohol,
hydrochloric acid or phosphoric acid.
Disposal and Recycling
End of Product Life
When this appliance has reached the end
of its serviceable life, it should be
disposed of in a safe manner, in
accordance with current local authority
recycling, or waste disposal policy.
Battery Disposal
Spent batteries should not be disposed
of with normal household waste. Contact
your local authority for information on
waste disposal and recycling.
Maintenance
This symbol on the product or packaging
indicates that this product should not be
disposed of with your other household
waste. Instead, it is your responsibility to
dispose of your waste equipment by
handing it over to a designated collection
point for the recycling of waste electrical
and electronic equipment. The separate
collection and recycling of your waste
equipment at the time of disposal will
help to conserve natural resources and
ensure that it is recycled in a manner that
protects human health and the
environment.
For more information about where you
can drop off your waste equipment for
recycling, please contact your local
council office, your household waste
disposal service or the shop where you
purchased the product.

12
Symptom Cause Remedy
Spout does not
dispense soap.
Senor cable not connected. Check that the sensor cable is
connected. If not connected,
connect sensor cable. Refer to
‘Installation’ section on pages
6-8.
Possible blockage in dispense
tube or dispense cable.
Remove pump from bottle and
clean tube.
Remove dispense cable from
pump and clean.
Low or no soap in bottle. Fill bottle with liquid soap.
When soap is at approximately
20mm from the bottom top soap
up.
No electrical power to pump. Ensure power cable is connected.
Refer to ‘Installation’ section on
pages 6-8.
No power to the
spout.
Mains power cable not
connected.
Connect mains power supply
cable. Refer to ‘Installation’
section on pages 6-8.
Mains power supply failed and
no batteries fitted or batteries
low.
Check mains power supply.
Insert / change batteries. Refer
to ‘Installation’ section on pages
6-8.
Spout dispenses
soap randomly
without a user
present.
Object in sensing range. Ensure the sensing range is
clear.
Troubleshooting

13
Symptom Cause Remedy
Sensor light not
working.
Sensor light faulty. Contact Bristan Customer
Services on 0844 701 6273.
Batteries are exhausted. Replace batteries.
Short cycles of
batteries.
Incorrect batteries fitted. Replace batteries. Ensure
batteries are 1.5V AA (LR6)
Alkaline batteries (preferably
=>2000mAh) for good battery life.
Infrared sensor
flickering.
Batteries running low. Replace batteries. Ensure
batteries are 1.5V AA (LR6)
Alkaline batteries (preferably
=>2000mAh) for good battery life.
Troubleshooting - cont.

14
Guarantee
At Bristan, we want to make things as
easy as possible for our customers.
That’s why we design products that are
easy to fit and use, and that are quality
tested to make sure they won’t let you
down. It’s also why we offer solid
guarantees on all products, effective from
the date of purchase, to give you peace of
mind.
All Bristan Commercial products are
covered by a 1 year guarantee. This also
includes 1 year labour cover which means
that, in the unlikely event that there is a
problem in the first year after purchase,
we’ll send one of our expert engineers to
fix it.
*Labour is provided by an approved
Bristan Care engineer or appointed
representative. The guarantee only applies
to products with a manufacturing fault.
There will be a call out charge for any
incidents where no fault has been found
with the product, or if the issue is due to
poor installation or maintenance.
Guarantee Terms and Conditions
This guarantee is in addition to your
statutory and other legal rights and is
subject to the following conditions:
• The product was purchased within the
United Kingdom or Republic of Ireland.
• The guarantee applies solely to the
original purchaser with proof of purchase.
• The installation must allow ready access
to all products for the purpose of
inspection, maintenance or replacement.
• Repair under this guarantee does not
extend the original expiry date. The
guarantee on any replacement parts or
product ends at the original expiry date
• Any part found to be defective during the
guarantee period will be replaced without
charge, providing that the product has
been installed in accordance with the
instructions given in this guide and used
as the manufacturer intended.
The guarantee does not cover
• Damage or defects caused by:
- General wear and tear (including special
non-chrome finishes;
- Components such as filters, seals, ‘O’
rings and washers)
- Incorrect installation
- Repair using non-Bristan part
- Accidental or wilful misuse
- Corrosion and the use of inappropriate
cleaning products.
- System debris including the build up of
limescale (which can be controlled
through regular servicing and
maintenance)
• Compensation for loss of use of the
product or consequential loss of any kind.
In the interests of continuous product
improvement, Bristan reserves the right
to alter product specifications without
notice.
The Bristan Product Guarantee does not
affect your statutory rights as a consumer.

15
Guarantee & Service Policy
Need help?
If this product does not function correctly
when first used, contact Bristan Care
Customer Service on 0844 701 6273
where our expert team of advisors will be
able to offer you help and advice.
Problems during the guarantee period
In the unlikely event that you encounter
any problems with the product during the
guarantee period, contact Bristan Care
Customer Service on 0844 701 6273 with
your proof of purchase and we will work to
resolve the problem quickly.
Bristan Care Customer Support
Bristan customers also benefit from the
support of Bristan Care, our
comprehensive customer support
package which offers:
Technical support hotline
(Tel: [phone]) with access to fully
trained advisors who can offer installation
advice, talk you through quick
maintenance checks, or recommend the
best course of action to fix any problems
with a product
Expert advice
Find easy to follow ‘how to’ video guides
and technical FAQs online at
www.bristan.com. Our guides take you
step-by-step through many product
installations and you can find plenty of
easy guides to quick product fixes and
servicing.
Spare parts
We hold thousands of spares and we keep
them for discontinued products for over
seven years. Spares can easily be ordered
online at www.bristan.com and are
dispatched the same day.
Expert plumbing engineers
If we can’t solve the problem over the
‘phone or with a spare part, then we’ll
send out one of our Bristan Care
engineers to take a look. Bristan Care
engineers provide free support for
products that are within guarantee, but
are also available to service products that
are out of guarantee for a small charge.
For details, please call customer services
on 0844 701 6273.

16
Bristan Group Ltd.
Birch Coppice Business Park
Dordon
Tamworth
Staffordshire
B78 1SG
Web: www.bristan.com
Email: enquir[email protected]om
A Masco Company
Part Number: FI Infrared Soap
Issue: D2
Useful contact details:
Customer Service:
0844 7016273
Customer Service Email:
[e-mail]
Customer Service Fax:
0844 7016275
Reception:
0844 7016274
Join us on...